DLA DSCC-VID-V62 06654 REV A-2011 MICROCIRCUIT DIGITAL ADVANCED BIPOLAR CMOS 3 3-V ABT 16-BIT TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Correct pin name 24 in terminal connection table, figure 4. - PHN 11-09-12 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawi

2、ng REV PAGE REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL, ADVANCED BIPOLAR CMOS, 3.

3、3-V ABT 16-BIT TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS, MONOLITHIC SILICON YY MM DD 06-08-16 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06654 REV A PAGE 1 OF 1 AMSC N/A 5962-V082-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

4、om IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 3.3-V ABT 16-bit transparent D-type latch with 3-state outputs microcircuit, with an operatin

5、g temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/06654 - 01 X E Drawing

6、 Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 SN74LVTH162373-EP 3.3-V ABT 16-bit transparent D-type latch with 3-state outputs 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline

7、letter Number of pins JEDEC PUB 95 Package style X 48 JEDEC MO-118 Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium

8、E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.

9、5 V to 4.6 V Input voltage range (VI) . -0.5 V to 7 V 2/ Voltage range applied to any output in the high-impedance or power-off state (VO) . -0.5 V to 7 V 2/ Voltage range applied to any output in the high state (VO) -0.5 V to VCC+ 0.5 V 2/ Current into any output in the low state (IO) . 30 mA Curre

10、nt into any output in the high state (IO) . 30 mA 3/ Input clamp current (IIK) (VIVCC. 4/ The package thermal impedance is calculated in accordance with JESD 51-7. 5/ Long-term high temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overa

11、ll device life. 6/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/066

12、54 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th St

13、reet, Suite 240S, Arlington, VA 22201.) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit contai

14、ner. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 D

15、esign, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline(s) shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diag

16、ram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Timing waveforms and test circuit. The timing waveforms and test circuit shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or netw

17、orking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VCCTemperature, TADevice type Limits Unit Min Max Input clamp voltage VIK

18、II= -18 Ma 2.7 V 25C, -55C to +125C All -1.2 V High level output voltage VOHIOH= -12 Ma 3 V 2 V Low level output voltage VOLIOL= 12 Ma 3 V 0.8 V Input current IIControl inputs VI= 5.5 V 0 V or 3.6 V 10 A Control inputs VI= VCCor GND 3.6 V 1 Data inputs, VI= VCC3.6 V 1 Data inputs, VI= 0 V 3.6 V -5 I

19、nput current (hold) II(hold)Data inputs, VI= 0.8 V 3 V 75 A Data inputs, VI= 2.0 V 3 V -75 3-state output current, high IOZHVO= 3 V 3.6 V 5 A 3-state output current, low IOZLVO= 0.5 V 3.6 V -5 A 3-state output current, power-up IOZPU2/ VO= 0.5 V to 3 V, OE= dont care 0 V to 1.5 V 100 A 3-state outpu

20、t current, power-down IOZPD2/ VO= 0.5 V to 3 V, OE= dont care 1.5 V to 0 V 100 A Quiescent supply current ICCOutputs high IO= 0, VI= VCCor GND 3.6 V 0.19 mA Outputs low IO= 0, VI= VCCor GND 3.6 V 5 Outputs disabled IO= 0, VI= VCCor GND 3.6 V 0.19 Quiescent supply current delta ICC3/ One input at VCC

21、 0.6 V, Other inputs at VCCor GND 3 V to 3.6 V 0.2 mA Input capacitance CiVI= 3 V or 0 V 3.3 V 25C 3 TYP pF Output capacitance CoVO= 3 V or 0 V 3.3 V 9 TYP See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY

22、CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions VCCTemperature, TADevice type Limits Unit Min Max Pulse duration, LE high twSee figure 5. 2.7 V 25C, -55C to +125C All 3 n

23、s 3.3 V 0.3 V 3 Setup time, data before LE tsuSee figure 5. 2.7 V 0.6 ns 3.3 V 0.3 V 1.3 Hold time, data after LE thSee figure 5. 2.7 V 1.1 ns 3.3 V 0.3 V 1 Propagation delay time, D to Q tPLHCL= 50 pF See figure 5. 2.7 V 5.7 ns 3.3 V 0.3 V 1.8 5 tPHL2.7 V 4.8 3.3 V 0.3 V 1.8 4.4 Propagation delay t

24、ime, LE to Q tPLHCL= 50 pF See figure 5. 2.7 V 6.2 ns 3.3 V 0.3 V 2.1 5.4 tPHL2.7 V 4.7 3.3 V 0.3 V 2.1 4.9 Propagation delay time, output enable, OEto Q tPZHCL= 50 pF See figure 5. 2.7 V 7 ns 3.3 V 0.3 V 1.7 5.6 tPZL2.7 V 5.9 3.3 V 0.3 V 1.7 5.3 Propagation delay time, output disable, OEto Q tPHZCL

25、= 50 pF See figure 5. 2.7 V 6.6 ns 3.3 V 0.3 V 2.3 6.3 tPLZ2.7 V 6.4 3.3 V 0.3 V 1 7.4 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full tem

26、perature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ On products compliant to MIL-PRF-38535, this parameter is not production tested. 3/ This is the increase in supply curr

27、ent for each input that is at the specified TTL voltage level, rather than VCCor GND. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 7 Case X Dim

28、ensions Symbol Inches Millimeters Symbol Inches Millimeters Min Max Min Max Min Max Min Max A - 0.110 - 2.79 E 0.395 0.420 10.03 10.67 A1 0.008 - 0.20 - E1 0.291 0.299 7.39 7.59 b 0.008 0.014 0.20 0.34 e 0.025 BSC 0.635 BSC c 0.005 0.010 0.13 0.25 L 0.020 0.040 0.51 1.02 D 0.620 0.630 15.75 16.00 NO

29、TES: 1. This drawing is subject to change without notice. 2. Falls within JEDEC MO-118. 3. All linear dimensions are in inches (millimeters). Millimeters equivalents are shown for general information only. 4. Body dimensions do not include mold flash or protrusion not to exceed 0.006 inches (0.15 mi

30、llimeters). FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 8 Inputs Output OELE D Q L H H H L H L L L L X Q0H X X Z H =

31、High voltage level X = Irrelevant L = Low voltage level Z = High Impedance state Q0= Level of Q before the indicated steady-state input conditions were established. FIGURE 2. Truth table. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

32、om IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol Terminal number Terminal symbol 1 1OE25 2LE 2 1Q1 26 2D8 3 1Q2 27 2D7 4 GND 28 GND 5 1Q3 29 2D6 6 1Q4 30 2D5 7 VCC31 VCC8

33、 1Q5 32 2D4 9 1Q6 33 2D3 10 GND 34 GND 11 1Q7 35 2D2 12 1Q8 36 2D1 13 2Q1 37 1D8 14 2Q2 38 1D7 15 GND 39 GND 16 2Q3 40 1D6 17 2Q4 41 1D5 18 VCC42 VCC19 2Q5 43 1D4 20 2Q6 44 1D3 21 GND 45 GND 22 2Q7 46 1D2 23 2Q8 47 1D1 24 2OE48 1LE FIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo repr

34、oduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06654 REV A PAGE 10 NOTES: 1. CLincludes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is low

35、, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. 3. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO= 50 , tr 2.5 ns, tf 2.5 ns.

36、 4. The outputs are measured one at a time, with one transition per measurement. FIGURE 5. Timing waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 D

37、WG NO. V62/06654 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, clas

38、sification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NO

39、TES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes witho

40、ut notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administr

41、ative control number 1/ Device manufacturer CAGE code Vendor part number Top-side marking V62/06654-01XE 01295 CLVTH162373MDLREP LVTH162373EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-