DLA DSCC-VID-V62 07646-2008 MICROCIRCUIT LINEAR DUAL DIFFERENTIAL COMPARATOR MONOLITHIC SILICON《单片硅双路差动比较器线性微电路》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKE

2、D BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, LINEAR, DUAL, DIFFERENTIAL COMPARATOR, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/07646 08-03-25 REV PAGE 1 OF 10 AMSC N/A 5962-V036-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

3、icense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance dual differential comparator microcircuit, with an operating temperature range of -55C

4、 to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/07646 - 01 X E Drawing Device type Case outline L

5、ead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 LM293-EP Dual differential comparator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 8 MS-012-AA Plastic

6、 surface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction

7、 or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . 36 V maximum 2/ Differential input voltage (VID) 36 V maximum 3/ Input voltage range (

8、either input) . -0.3 V to 36 V Output voltage (VO) 36 V maximum Output current (IO) . 20 mA maximum Duration of output short circuit to ground . Unlimited 4/ Package thermal impedance 97C/W 5/ 6/ Operating virtual junction temperature (TJ) +150C Storage temperature range -65C to +150C 1.4 Recommende

9、d operating conditions. 7/ Supply voltage (VCC) . 5 V Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or

10、any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage values, except differential voltages, are with respect to GND. 3/ Differential voltage

11、s are at +INPUT terminal with respect to INPUT terminal. 4/ Short circuits from outputs to VCCcan cause excessive heating and eventual destruction. 5/ Maximum power dissipation is a function of TJ(max), JAand TA. The maximum allowable power dissipation at any allowable ambient temperature is PD= (TJ

12、(max) TA) / JA. Operating at the absolute maximum junction temperature (TJ) of +150C can affect reliability. 6/ The package thermal impedance is calculated in accordance with JESD 51-7. 7/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The m

13、anufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/0

14、7646 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Ma

15、rking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers

16、 part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, const

17、ruction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitt

18、ed without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions 2/ VCC= 5 V unless otherwise specifiedTemperature, TADevice type Min Max Unit Inpu

19、t offset voltage VIOVCC= 5 V to 30 V, +25C 01 5 mV VO= 1.4 V, VIC= VIC(min) -55C to +125C 9 Input offset current IIOVO= 1.4 V +25C 01 50 nA -55C to +125C 250 Input bias current IIBVO= 1.4 V +25C 01 -250 nA -55C to +125C -400 Common mode 3/ input voltage range VICR+25C 01 0 to VCC- 1.5 V -55C to +125

20、C 0 to VCC- 2 Large signal differential voltage amplification AVDVCC= 15. V, VO= 1.4 V to 11.4 V, RL 15 k to VCC+25C 01 50 V/mV High level output current IOHVOH= 5 V, VID= 1 V +25C 01 50 nA VOH= 30 V, VID= 1 V -55C to +125C 1 A Low level output voltage VOLIOL= 4 mA, VID= -1 V +25C 01 400 mV -55C to

21、+125C 700 Low level output current IOLVOL = 1.5 V, VID= -1 V +25C 01 6 mA Supply current ICCVCC= 5 V, RL= +25C 01 1 mA VCC= 30 V, RL= -55C to +125C 2.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENT

22、ER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions 2/ VCC= 5 V unless otherwise specifiedTemperature, TADevice type Min Max Unit Response time 100 mV input step with 4/ 5/ 5

23、mV overdrive, RLconnected to 5 V through 5.2 k, CL= 15 pF +25C 01 1.3 typical s TTL level input step, 4/ 5/ RLconnected to 5 V through 5.2 k, CL= 15 pF 0.3 typical 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified

24、 temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, all characteri

25、stics are measured with zero common mode input voltage. 3/ The voltage at either input or common mode should not be allowed to go negative by more than 0.3 V. The upper end of the common mode voltage range is +VCC 1.5 V for the INPUT terminal and the +INPUT terminal can exceed the VCClevel; the comp

26、arator provides a proper output state. Either or both inputs can go to 30 V without damage. 4/ CLincludes probe and jig capacitance. 5/ The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V. Provided by IHSNot for ResaleNo reproduct

27、ion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 7 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU

28、PPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 8 Case X continued. Dimensions Inches Millimeters Symbol Min Max Min Max A - 0.069 - 1.75 A1 0.004 0.010 0.10 0.25 b 0.012 0.020 0.31 0.51 c 0.007 0.010 0.17 0.25 D 0.189 0.197 4.80 5.00 E 0.150 0.157 3.80 4.

29、00 E1 0.228 0.244 5.80 6.20 e 0.050 BSC 1.27 BSC L 0.016 0.050 0.40 1.27 n 8 8 NOTES: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. Body length does not include mold flash, protrusion, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed

30、 0.006 inch (0.15 mm) per end. 3. Body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm) per side. 4. Falls within JEDEC MS-012-AA. FIGURE 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

31、m IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol 1 OUTPUT 1 2 -INPUT 1 3 +INPUT 1 4 GND 5 +INPUT 2 6 -INPUT 2 7 OUTPUT 2 8 VCCFIGURE 2. Terminal connections. Provided by IHS

32、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07646 REV PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspectio

33、n and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, pack

34、aging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data con

35、tained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s)

36、of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Package Topside marking Vendor part number V62/07646-01XE 01295 Reel of 2500 LM293E LM293

37、MDREP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-