DLA DSCC-VID-V62 08607 REV A-2008 MICROCIRCUIT DIGITAL-LINEAR PROGRAMMABLE DELAY SUPERVISORY CIRCUIT MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device type 01. Make changes to VILand VIH. Update unreleased vendor part numbers from “REP” to “TEP”. - ro 08-11-20 R. HEBER Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV A A A A A A A A A A A REV STATUS OF PAGES PAG

2、E 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, DIGITAL-LINEAR, PROGRAMMABLE DELAY SUPERVISORY CIRCUIT, MONOLITHIC SILICON

3、 SIZE A CODE IDENT. NO. 16236 DWG NO. V62/08607 08-08-07 REV A PAGE 1 OF 11 AMSC N/A 5962-V004-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08607 REV A PAGE

4、2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance programmable delay supervisory circuit microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identific

5、ation. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/08607 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Nominal Threshold (VIT) Device type

6、Generic supply voltage voltage Circuit function 01 TPS3808G01 Adjustable 0.405 V Programmable delay supervisory circuit 02 TPS3808G09 0.9 V 0.84 V Programmable delay supervisory circuit 03 TPS3808G12 1.2 V 1.12 V Programmable delay supervisory circuit 04 TPS3808G125 1.25 V 1.16 V Programmable delay

7、supervisory circuit 05 TPS3808G15 1.5 V 1.40 V Programmable delay supervisory circuit 06 TPS3808G18 1.8 V 1.67 V Programmable delay supervisory circuit 07 TPS3808G25 2.5 V 2.33 V Programmable delay supervisory circuit 08 TPS3808G30 3.0 V 2.79 V Programmable delay supervisory circuit 09 TPS3808G33 3.

8、3 V 3.07 V Programmable delay supervisory circuit 10 TPS3808G50 5.0 V 4.65 V Programmable delay supervisory circuit 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 6 MO-178-AB Plastic surface mount 1.2.3 Lead finishes. Th

9、e lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

10、se from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08607 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Input voltage range (VDD) . -0.3 V to 7.0 V CTvoltage range (VCT) -0.3 V to VDD+ 0.3 V Other voltage ranges: VRESET, VMR, VSENSE-0.3 V to 7 V RES

11、ET pin current 5 mA Operating junction temperature (TJ) . +150C 2/ Storage temperature range (Tstg) -65C to +150C Electrostatic discharge (ESD) rating: Human body model (HDM) . 2 kV Charge device model (CDM) 500 V Thermal resistance, junction to case (JC) . 55C/W Thermal resistance, junction to ambi

12、ent (JA) 290C/W typical 1.4 Recommended operating conditions. 3/ Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device a

13、t these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ As a result of the low dissipated power in this device, it is assumed that TJ= TA. 3/ U

14、se of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without

15、 license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08607 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Al

16、liance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier

17、 C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are a

18、s specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The termin

19、al connections shall be as shown in figure 2. 3.5.3 Truth table. The truth table shall be as shown in figure 3. 3.5.4 Timing waveforms. The timing waveforms shall be as shown in figure 4. 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspectio

20、n and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. Provided by IHSNot for ResaleNo reproduction or networking pe

21、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08607 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions 2/Temperature, TA Device type Min Max Unit Input supply range VDD-55C to +1

22、25C All 1.7 6.5 V Supply current (current into VDDpin) IDDVDD= 3.3 V, RESET not asserted MR , RESET , CTopen -55C to +125C All 5.0 A VDD= 6.5 V, RESET not asserted MR , RESET , CTopen 6.0 Low level output voltage VOL1.3 V VDDVIT RESET L 0 L L 1 L H 0 L H 1 H FIGURE 3. Truth table. MR and SENSE reset

23、 timing FIGURE 4. Timing diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08607 REV A PAGE 11 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, pack

24、aging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data con

25、tained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s)

26、of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ 2/ 3/ Device manufacturer CAGE code Nominal 4/ supply voltage Vendor part number V62/08607-01XE 01295 Adjustable TPS380

27、8G01MDBVTEP V62/08607-02XE 5/ 0.9 V TPS3808G09MDBVTEP V62/08607-03XE 5/ 1.2 V TPS3808G12MDBVTEP V62/08607-04XE 5/ 1.25 V TPS3808G125MDBVTEP V62/08607-05XE 5/ 1.5 V TPS3808G15MDBVTEP V62/08607-06XE 5/ 1.8 V TPS3808G18MDBVTEP V62/08607-07XE 5/ 2.5 V TPS3808G25MDBVTEP V62/08607-08XE 5/ 3.0 V TPS3808G30

28、MDBVTEP V62/08607-09XE 01295 3.3 V TPS3808G33MDBVREP V62/08607-10XE 5/ 5.0 V TPS3808G50MDBVTEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and ordering information, see the package

29、option addendum at the end of the manufacturers data sheet , or use website . 3/ Package drawings, thermal data, and symbolization are available at 4/ Customer threshold voltages from 0.82 V to 3.3 V, 4.4 V to 5.0 V are available through the use of factory EEPROM programming. Minimum order quantiti

30、es apply. Contact factory for details and availability. 5/ Product preview. Contact the manufacturer sales representative for availability. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-