DLA DSCC-VID-V62 08618-2008 MICROCIRCUIT LINEAR CMOS SINGLE SUPPLY RAIL TO RAIL OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing

2、YY-MM-DD CHECKED BY RAJESH PITHADIA APPROVED BY ROBERT M. HEBER TITLE MICROCIRCUIT, LINEAR, CMOS SINGLE SUPPLY, RAIL TO RAIL OPERATIONAL AMPLIFIER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/08618 08-10-07 REV PAGE 1 OF 15 AMSC N/A 5962-V062-08 Provided by IHSNot for ResaleNo reprod

3、uction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance single supply rail to rail operational amplifi

4、er microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering document

5、ation: V62/08618 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 OPA340-EP Single supply, rail to rail single operational amplifier 02 OPA2340-EP Single supply, rail to rail dual operationa

6、l amplifier 03 OPA4340-EP Single supply, rail to rail quad operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 MO-178-AA Plastic surface mount Y 8 MS-012-AA Plastic surface mount Z 14 MS-012-AB Plastic

7、 surface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction

8、 or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) 5.5 V Signal input voltage (VI) . -VS 0.5 V to +VS+ 0.5 V 2/ Signal input current (VO) 10

9、 mA 2/ Power dissipation (PD) at TA= +125C: Case X . 125 mW Case Y . 166 mW Case Z . 250 mW Output short circuit . Continuous 3/ Storage temperature range (TSTG) -55C to +125C Operating virtual junction temperature (TJ) +150C Thermal resistance, junction to ambient (JA): X package 200C/W Y package 1

10、50C/W Z package . 100C/W 1.4 Recommended operating conditions. 4/ Supply voltage range (VS) 2.7 V to 5 V Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only,

11、 and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Input terminals are diode clamped to the power

12、 supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should be current limited to 10 mA or less. 3/ Short circuit to ground, one amplifier per package. 4/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manu

13、facturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/0861

14、8 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marki

15、ng. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers pa

16、rt number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construc

17、tion, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitte

18、d without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions 2/ VS= 2.7 V to 5 V unless otherwise specifiedTemperature, TADevice type Min Max Un

19、it Offset voltage section Input offset voltage VOSVS= 5 V +25C 01 500 V -55C to +125C 1600 Input offset voltage versus temperature VOS/ T +25C 01 2.5 typical V/C Input offset voltage versus power supply PSRR VS= 2.7 V to 5.5 V, VCM= 0 V -55C to +125C 01 150 V/V Channel separation, dc +25C 01 0.2 typ

20、ical V/V Input bias current section Input bias current IB-55C to +125C 01 500 pA Input offset current IOS-55C to +125C 01 600 pA Noise section Input voltage noise f = 0.1 kHz to 50 kHz +25C 01 8 typical Vrms Input voltage noise density enf = 1 kHz +25C 01 25 typical nV / Hz Current noise density inf

21、 = 1 kHz +25C 01 3 typical fA / Hz Input voltage range section Common mode voltage range VCM-55C to +125C 01 -0.3 +VS+ 0.3 V Common mode rejection ratio CMRR -0.3 V VCM ( +VS) 1.8 V +25C 01 78 dB -55C to +125C 75 -0.3 V VCM 5.3 V, +25C 70 VS= 5 V -55C to +125C 64 -0.3 V VCM 3 V, VS= 2.7 V +25C 66 Se

22、e footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits

23、Test Symbol Conditions 2/ VS= 2.7 V to 5 V unless otherwise specifiedTemperature, TADevice type Min Max Unit Input impedance section Differential input 3/ impedance +25C 01 1013| 3 typical | pF Common mode 3/ input impedance +25C 01 1013| 6 typical | pF Open loop gain section Open loop voltage gain

24、AOL10 mV VO (+VS) 10 mV, RL= 100 k -55C to +125C 01 103 dB 70 mV VO (+VS) 70 mV, RL= 10 k 98 250 mV VO (+VS) 250 mV, RL= 2 k 92 Frequency response section Gain bandwidth product GBW G = 1 +25C 01 5.5 typical MHz Slew rate SR VS= 5 V, G = 1, CL= 100 pF +25C 01 6 typical V/s Settling time, 0.1 % tSVS=

25、 5 V, 2 V step, CL= 100 pF +25C 01 1 typical s Settling time, 0.01 % tSVS= 5 V, 2 V step, CL= 100 pF +25C 01 1.6 typical s Overload recovery time VIN G = VS+25C 01 0.2 typical s Total harmonic distortion + noise THD + N VS= 5 V, VO= 3 VPP, 4/ G = 1, f = 1 kHz +25C 01 0.0007 typical % See footnotes a

26、t end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 7 TABLE I. Electrical performance characteristics - Continued. 1/ Limits Test Symbol

27、 Conditions 2/ VS= 2.7 V to 5 V unless otherwise specifiedTemperature, TADevice type Min Max Unit Output section RL= 100 k, AOL 104 dB -55C to +125C 01 10 mV Voltage output 5/ swing from rail RL= 10 k, AOL 98 dB 70 RL= 2 k, AOL 92 dB 250 Short circuit current ISC+25C 01 50 typical mA Power supply se

28、ction Specified voltage range VS-55C to +125C 01 2.7 5 V Operating voltage range +25C 01 2.5 to 5.5 typical V IQIO= 0, VS= 5 V +25C 01 950 A Quiescent current (per amplifier) -55C to +125C 1300 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product

29、performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless other

30、wise specified, VS= 5 V, RL= 10 k connected to VS/ 2, VOUT= VS/ 2. 3/ The | symbols represent that the values and symbols are in parallel to each other. 4/ VOUT= 0.25 V to 3.25 V. 5/ Output voltage swings are measured between the output and power supply rails. Provided by IHSNot for ResaleNo reprodu

31、ction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 8 Case X FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

32、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 9 Case X Dimensions Symbol Inch Millimeters Min Max Min Max A - .057 - 1.45 A1 .000 .005 0.00 0.15 b .011 .019 0.30 0.50 c .003 .008 0.08 0.22 D .108 .120 2.75 3.05 E .057 .068 1.45 1.75 E1 .102 .118 2.60

33、3.00 e .037 BSC 0.95 BSC L .011 .021 0.30 0.55 L1 .009 BSC 0.25 BSC n 5 leads 5 leads NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 mm ( .005 i

34、nch ) per side. 3. Falls within JEDEC MO-178-AA. FIGURE 1. Case outlines Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 10 Case Y FIGURE

35、 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 11 Case Y Dimensions Inches Millimeters Symbol Min Max Min Max A - 0.

36、069 - 1.75 A1 0.004 0.010 0.10 0.25 b 0.012 0.020 0.31 0.51 c 0.007 0.010 0.17 0.25 D 0.189 0.197 4.80 5.00 E 0.150 0.157 3.80 4.00 E1 0.228 0.244 5.80 6.20 e 0.050 BSC 1.27 BSC L 0.016 0.050 0.40 1.27 n 8 8 NOTES: 1. Controlling dimensions are inch, millimeter dimensions are given for reference onl

37、y. 2. Body length does not include mold flash, protrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall not exceed 0.006 inch (0.15 mm) per end. 3. Body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm) per side. 4. Falls within JEDEC MS-012-

38、AA. FIGURE 1. Case outlines Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 12 Case Z FIGURE 1. Case outlines Continued. Provided by IHSN

39、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 13 Case Z Dimensions Inches Millimeters Symbol Min Max Min Max A - .069 - 1.75 A1 .004 .010 0.10 0.25 b .012 .020 0.

40、31 0.51 c .007 .010 0.17 0.25 D .337 .344 8.55 8.75 e .050 BSC 1.27 BSC E .150 .157 3.80 4.00 E1 .228 .244 5.80 6.20 L .016 .050 0.40 1.27 n 14 leads 14 leads NOTES: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. Body length does not include mold flash, pr

41、otrusion, or gate burrs. Mold flash, protrusion, or gate burrs shall not exceed 0.006 inch (0.15 mm) per end. 3. Body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm) per side. 3. Falls within JEDEC MO-012-AB. FIGURE 1. Case outlines - Continued. Provided

42、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 14 Device types 01 01 02 03 Case outlines X Y Y Z Terminal number Terminal symbol 1 OUTPUT NC OUTPUT A OUTPU

43、T A 2 -VS-INPUT -INPUT A -INPUT A 3 +INPUT +INPUT +INPUT A +INPUT A 4 -INPUT-VS-VS+VS5 +VSNC +INPUT B +INPUT B 6 - OUTPUT -INPUT B -INPUT B 7 - +VSOUTPUT B OUTPUT B 8 - NC +VSOUTPUT C 9 - - - -INPUT C 10 - - - +INPUT C 11 - - - -VS12 - - - +INPUT D 13 - - - -INPUT D 14 - - - OUTPUT D NC = No connect

44、ion FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/08618 REV PAGE 15 4. VERIFICATION 4.1 Product assurance requirements. The manuf

45、acturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARA

46、TION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class

47、 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggeste