DLA DSCC-VID-V62 11610-2011 MICROCIRCUIT LINEAR CMOS OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONSLTR DESCRIPTION DATE APPROVEDPrepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY RAJ

2、ESH PITHDIA TITLE MICROCIRCUIT, LINEAR, CMOS, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON 11-09-20 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/11610 REV PAGE 1 OF 11 AMSC N/A 5962-V074-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

3、om IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance CMOS operational amplifier microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor

4、 Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/11610 - 01 X E Drawing Device type Case outline Lead finish number (Se

5、e 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 OPA365-EP CMOS 50 MHz gain bandwidth operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 MO-178-AA Plastic

6、 small outline surface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plateC Gold plateD PalladiumE Gold flash palladium Z Other Provided by IHSNot for ResaleNo r

7、eproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) 5.5 V Signal input terminals, voltage . (-V) 0.5 V to (+V) + 0.5 V 2/ Signal input termi

8、nals, current 10 mA 2/ Output short circuit duration . Continuous 3/ 4/ Power dissipation (PD) . 56.25 mW Junction temperature range (TJ) +150C Storage temperature range (TSTG) -65C to +150C Electrostatic discharge (ESD) rating: Human body model (HBM) . 4000 V Charged device model (CDM) 1000 V Machi

9、ne model (MM) . 200 V Thermal resistance, junction to case (JC) . 69.4C/W Thermal resistance, junction to ambient (JA) 200C/W typical 1.4 Recommended operating conditions. 5/ Supply voltage range (VS) 2.2 V to 5.5 V Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those l

10、isted under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated co

11、nditions for extended periods may affect device reliability. 2/ Input terminals are diode clamped to the power supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should be current limited to 10 mA or less. 3/ Short circuit to ground, one amplifier per package. 4/ Cont

12、inuous output current greater than 20 mA for extended periods may affect product reliability. 5/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyo

13、nd the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconducto

14、r Devices (Applications for copies should be addressed to the JEDEC Office, 3103 North 10th Street, Suite 240-S, Arlington, VA 22201-2107 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 he

15、rein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and

16、 recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outli

17、ne shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V

18、62/11610 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min Max Offset voltage Input offset voltage VOS+25C 01 200 V -55C to +125C 450 Input offset voltage drift dVOS/ dT -55C to +125C 01 3 typical V / C Input offset vol

19、tage versus power supply PSRR VS= +2.2 V to +5.5 V -55C to +125C 01 100 V/V Input bias current Input bias current IB+25C 01 10 pA -55C 0.5 typical +125C 60 typical Input offset current IOS+25C 01 10 pA Noise Input voltage noise enf = 0.1 Hz to 10 Hz +25C 01 5 typical VPPInput voltage noise density e

20、n f = 100 kHz +25C 01 4.5 typical nV / Hz Input current noise density inf = 10 kHz +25C 01 4 typical fA / Hz Input voltage range Common mode voltage range VCM-55C to +125C 01 (-V) 0.1 (+V) + 0.1 V Common mode rejection ratio CMRR (-V) 0.1 V VCM (+V) + 0.1 V -55C to +125C 01 96.5 dB Input capacitance

21、 Differential +25C 01 6 typical pF Common mode +25C 01 2 typical pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 6 TABLE I.

22、Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min Max Open loop gain Open loop voltage gain AOL100 mV VO (+V) 100 mV, RL= 10 k -55C to +125C 01 96.5 dB 200 mV VO (+V) 200 mV, RL= 600 +25C 100 200 mV VO (+V) 200 mV, RL= 600 -55C t

23、o +125C 91 Frequency response Gain bandwidth product GBW +25C 01 50 typical MHz Slew rate SR VS= 5 V, G = +1 +25C 01 25 typical V/s Settling time tS0.1%, VS= 5 V, 4 V step, G = +1 +25C 01 200 typical ns 0.01%, VS= 5 V, 4 V step, G = +1 300 typical Overload recovery time VS= 5 V, VINx gain VS+25C 01

24、0.1 typical s Total harmonic 3/ distortion + noise THD + N VS= 5 V, RL= 600 , VO= 4 VPP, G = +1, f = 1 kHz +25C 01 0.0004 typical % Output Voltage output swing from rail VS= 5.5 V, RL= 10 k, -55C to +125C 01 20 mV Short circuit current 4/ ISC+25C 01 65 typical mA Capacitive load drive CL+25C 01 100

25、typical pF Open loop output impedance f = 1 MHz, IO= 0 +25C 01 30 typical See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 7 TAB

26、LE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min Max Power supply Specified voltage range VS-55C to +125C 01 2.2 5.5 V Quiescent current per amplifier IQIO= 0 +25C 01 5 mA -55C to +125C 5.5 1/ Testing and other quality con

27、trol techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product

28、 performance is assured by characterization and/or design. 2/ Unless otherwise specified, VS= 2.2 V to 5.5 V, RL= 10 k connected to VS/2, VCM= VS/2, and VOUT=VS/2. 3/ Third order filter, bandwidth 80 kHz at -3 dB. 4/ Continuous output current greater than 20 mA for extended periods may affect produc

29、t reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 8 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking per

30、mitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 9 Case X Dimensions Symbol Inch Millimeters Min Max Min Max A - .057 - 1.45 A1 .000 .006 0.00 0.15 b .011 .019 0.30 0.50 c .003 .008 0.08 0.22 D .108 .120 2.75 3.05 E .057

31、.068 1.45 1.75 E1 .102 .118 2.60 3.00 e .037 BSC 0.95 BSC L .011 .022 0.30 0.55 L1 .009 - 0.25 - n 5 leads 5 leads NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shal

32、l not exceed 0.15 mm (.006 inch) per side. 3. Falls with JEDEC MO-178-AA. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/11610 REV PAGE 10

33、 Device type 01 Case outline X Terminal number Terminal symbol 1 VOUT2 -VS3 +INPUT 4 -INPUT 5 +VSFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO.

34、V62/11610 REV PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classificatio

35、n, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 E

36、SDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice

37、. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative con

38、trol number 1/ 2/ 3/ Device manufacturer CAGE code Top side marking Vendor part number V62/11610-01XE 01295 OUNM OPA365AMDBVTEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and order

39、ing information, see the package option addendum at the end of the manufacturers data sheet , or use website . 3/ Package drawings, thermal data, and symbolization are available at CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-