DLA DSCC-VID-V62 12626-2012 MICROCIRCUIT LINEAR CMOS 3 MHz LOW POWER DUAL OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ Original

2、 date of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, CMOS, 3 MHz, LOW POWER, DUAL OPERATIONAL AMPLIFIER, MONOLITHIC SILICON 12-10-09 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12626 REV PAGE 1 OF 12 AMSC N/A 5962-V091-12 Provided by IHSNot for

3、ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance CMOS, 3 MHz, low power, dual operational

4、amplifier microcircuit, with an operating temperature range of -40C to +150C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering d

5、ocumentation: V62/12626 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 OPA2314 CMOS, 3 MHz, low power, dual operational amplifier 1.2.2 Case outline(s). The case outline(s) are as specifie

6、d herein. Outline letter Number of pins JEDEC PUB 95 Package style X 8 See figure 1 Plastic bottom terminal chip carrier with thermal pad 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot sold

7、er dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 3 1.3 Absolute maximum ratings

8、. 1/ Supply voltage (VS) 7 V Signal input terminals: Voltage . -VS 0.5 V to +VS+ 0.5 V 2/ Current . 10 mA 2/ Output short circuit . Continuous 3/ Power dissipation (PD) . 2.42 mW Junction temperature range (TJ) +170C Storage temperature range (TSTG) -65C to +150C Electrostatic discharge (ESD) rating

9、: Human body model (HBM) . 4,000 V Charged device model (CDM) 1,000 V Machine model (MM) . 200 V 1.4 Recommended operating conditions. 4/ Supply voltage range (VS) +1.8 V to +5.5 V Operating free-air temperature range (TA) . -40C to +150C 1.5 Thermal characteristics. Thermal metric Symbol Case X Uni

10、t Thermal resistance, junction-to-ambient JA53.8 C/W Thermal resistance, junction-to-case (top) JC(TOP)69.2 C/W Thermal resistance, junction-to-board JB20.1 C/W Characterization parameter, junction-to-top JT3.8 C/W Characterization parameter, junction-to-board JB20.0 C/W Thermal resistance, junction

11、-to-case (bottom) JC(BOTTOM)11.6 C/W 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating co

12、nditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Input terminals are diode clamped to the power supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should be current limited to 10 mA or less.

13、 3/ Short circuit to ground, one amplifier per package. 4/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSN

14、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB 95 Registered and Standard Outlines for Semicondu

15、ctor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in

16、 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maxi

17、mum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The cas

18、e outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DW

19、G NO. V62/12626 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/ 3/ VS= +1.8 V to +5.5 VTemperature, TA Device type Limits Unit Min Max Offset voltage Input offset voltage VOSVCM= +VS 1.3 V +25C 01 2.5 mV -40C to +150C 3.5 Input offset voltage versus temperatu

20、re VOS/ T -40C to +150C 01 1 typical V/ C Input offset voltage versus power supply PSRR VCM= +VS 1.3 V +25C 01 78 dB -40C to +150C 72 Channel separation, dc CS At dc +25C 01 10 typical V/V Input voltage range Common mode voltage range +25C 01 -VS-0.2 +VS+ 0.2 V Common mode rejection ration CMRR VS=

21、1.8 V, -VS 0.2 V VS+25C 01 5.2 typical s Total harmonic 6/ distortion + noise THD+N VS= 5.0 V, VO= 1 VRMS, G = +1, f = 1 kHz, RL= 10 k +25C 01 0.001 typical % Output Voltage output swing from supply rails VOVS= 1.8 V, RL= 10 k +25C 01 15 mV VS= 5.5 V, RL= 10 k 20 VS= 1.8 V, RL= 2 k 30 VS= 5.5 V, RL=

22、 2 k 40 VS= 5.5 V, RL= 10 k -40C to +150C 30 VS= 5.5 V, RL= 2 k 60 typical Short circuit current ISCVS= 5.0 V +25C 01 20 typical mA Open loop output impedance ROVS= 5.5. V, f = 100 Hz +25C 01 570 typical See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permit

23、ted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 8 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/ 3/ VS= +1.8 V to +5.5 VTemperature, TA Device type Limits Unit Min Max Power supply S

24、pecified voltage range VS+25C 01 1.8 5.5 V Quiescent current per amplifier IQVS= 1.8 V, IO= 0 mA +25C 01 180 A VS= 5.0 V, IO= 0 mA 190 -40C to +150C 220 Power on time VS= 0 V to 5 V, to 90% IQlevel +25C 01 44 typical s Temperature Specified range 01 -40 +150 C Operating range 01 -40 +150 C Storage r

25、ange 01 -65 +150 C 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In

26、the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, parameters with minimum and maximum specification limits are 100% production tested at 25C. Over temperature limits are based on characterization and statistic

27、al analysis. 3/ Unless otherwise specified, TA= +25C, RL= 10 k connected to VS/ 2, VCM= VS/ 2, and VOUT= VS/ 2. 4/ Specified by design and/or characterization, not production tested. 5/ Signifies the slower value of the positive or negative slew rate. 6/ Third order filter, bandwidth = 80 kHz at -3

28、dB. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 9 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted with

29、out license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 10 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A 0.031 0.039 0.80 1.00 A1 0.007 REF 0.20 REF A2 0.00 0.001 0.00 0.05 b 0.009 0.014 0.25 0.37 b1 0.011 0.019 0.30 0.50 D

30、 0.112 0.124 2.85 3.15 E 0.112 0.124 2.85 3.15 e 0.025 BSC 0.65 BSC NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. The package thermal pad must be soldered to the board for thermal and mechanical performance. Connect thermal pad to VS. FIGURE 1. Cas

31、e outline - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 11 Device type 01 Case outline X Terminal number Terminal symbol 1 OUTPUT A 2 -INPUT A

32、3 +INPUT A 4 -VS5 +INPUT B 6 -INPUT B 7 OUTPUT B 8 +VSFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12626 REV PAGE 12 4. VERIFICATION 4.1 P

33、roduct assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sens

34、itive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge se

35、nsitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes

36、are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supp

37、ly at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ 2/ 3/ Device manufacturer CAGE code Top side marking Transport media Vendor part number V62/12626-01XE 01295 OUVS Small reel OPA2314ASDRBTEP 1/ The vendor item drawing establishes an administ

38、rative control number for identifying the item on the engineering documentation. 2/ For the most current package and ordering information, see the package option addendum at the end of the manufacturers data sheet. 3/ Package drawings, standard packaging quantities, thermal data, symbolization, and

39、printed circuit board (PCB) design guidelines are available from the manufacturer. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-