DLA DSCC-VID-V62 12627-2013 MICROCIRCUIT LINEAR 36 V SINGLE SUPPLY LOW POWER OPERATIONAL AMPLIFIER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ Original da

2、te of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, 36 V, SINGLE SUPPLY, LOW POWER OPERATIONAL AMPLIFIER, MONOLITHIC SILICON 13-01-23 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12627 REV PAGE 1 OF 11 AMSC N/A 5962-V092-12 Provided by IHSNot for R

3、esaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 36 V, single supply, low power operational

4、 amplifier microcircuit, with an operating temperature range of -40C to +150C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering

5、documentation: V62/12627 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 OPA170-EP 36 V, single supply, low power operational amplifier 1.2.2 Case outline(s). The case outline(s) are as spe

6、cified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 See figure 1 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C G

7、old plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) .

8、20 V, +40 V (single supply) Signal input terminals: Voltage . -VS 0.5 V to +VS+ 0.5 V Current . 10 mA Output short circuit . Continuous 2/ Junction temperature range (TJ) +150C Storage temperature range (TSTG) -65C to +150C Electrostatic discharge (ESD) rating: Human body model (HBM) . 4000 V Charge

9、d device model (CDM) 750 V 1.4 Recommended operating conditions. 3/ Operating free-air temperature range (TA) . -40C to +150C 1.5 Thermal characteristics. Thermal metric Symbol Case X Unit Thermal resistance, junction-to-ambient JA226.8 C/W Thermal resistance, junction-to-case (top) JC(TOP)80.3 C/W

10、Thermal resistance, junction-to-board JB42.9 C/W Characterization parameter, junction-to-top JT3.2 C/W Characterization parameter, junction-to-board JB42.5 C/W 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and

11、 functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Short circuit to ground, one amplifier per package

12、. 3/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted w

13、ithout license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance

14、, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ES

15、DS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as spec

16、ified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal con

17、nections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Cond

18、itions 2/ VS= +4 V to +36 V, unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Offset voltage Input offset voltage VOS+25C 01 1.8 mV -40C to +150C 2.5 Input offset voltage versus temperature VOS/ T -40C to +150C 01 0.3 typical V/C Input offset voltage versus power supply PSRR

19、VS= +4 V to +36 V -40C to +150C 01 5 V/V Channel separation, dc CS At dc +25C 01 5 typical V/V Input bias current Input bias current IB+25C 01 15 pA -40C to +150C 8 nA Input offset current IOS+25C 01 15 pA -40C to +150C 8 nA Noise Input voltage noise f = 0.1 Hz to 10 Hz +25C 01 2 typical VPPInput vo

20、ltage noise density en f = 100 Hz +25C 01 22 typical nV / f = 1 kHz 19 typical Hz Input voltage range Common mode 3/ voltage range VCM+25C 01 -VS- 0.1 +VS- 2 V Common mode rejection ratio CMRR VS= 2 V, -VS 0.1 V VS+25C 01 2 typical s Total harmonic distortion + noise THD+N VO= 3 VRMS, G = +1, f = 1

21、kHz +25C 01 0.0002 typical % See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 7 TABLE I. Electrical performance characteristics

22、Continued. 1/ Test Symbol Conditions 2/ VS= +4 V to +36 V, unless otherwise specifiedTemperature, TADevice type Limits Unit Min Max Output Voltage output swing from rail VOPositive rail VS= +4 V to +36 V, IL= 0 mA +25C 01 10 mV VS= +4 V to +36 V, ILsourcing 1 mA 130 Negative rail VS= +4 V to +36 V,

23、IL= 0 mA +25C 8 VS= +4 V to +36 V, ILsinking 1 mA 72 Over temperature VS= 5 V, RL= 10 k -40C to +150C -VS+ 0.03 +VS- 0.05 V AOL 110 dB, RL= 10 k -VS+ 0.35 +VS- 0.35 Short circuit current ISCThe limits are dependent on the negative or positive source +25C 01 +17/-20 typical mA Open loop output resist

24、ance ROf = 1 MHz, IO= 0 A +25C 01 900 typical Power supply Specified voltage range VS+25C 01 +2.7 +36 V Quiescent current per amplifier IQIO= 0 mA +25C 01 145 A -40C to +150C 160 Temperature Specified range 01 -40 +125 C Operating range 01 -40 +150 C 1/ Testing and other quality control techniques a

25、re used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is a

26、ssured by characterization and/or design. 2/ Unless otherwise specified, TA= +25C, VCM= VOUT= VS/ 2, and RL= 10 k connected to VS/ 2. 3/ The input range can be extended beyond +VS 2 V up to +VS. 4/ The | symbolizes that the input impedance is being represented as the resistance value is in parallel

27、with the capacitance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 8 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or network

28、ing permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 9 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A .019 .023 0.50 0.60 A1 .000 .001 0.00 0.05 b .005 .009 0.15 0.25 c .003 .007 0.08 0.18 D .059 .066 1.

29、50 1.70 E .043 .051 1.10 1.30 E1 .059 .066 1.50 1.70 e .019 BSC 0.50 BSC L .005 .010 0.13 0.27 L1 .007 .015 0.20 0.40 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Dimensions D and E do not include mold flash, interlead flash, protrusion, or gate b

30、urrs. Mold flash, interlead flash, protrusion, or gate burrs shall not exceed 0.15 mm (0.006 inch) per end or side. FIGURE 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE I

31、DENT NO. 16236 DWG NO. V62/12627 REV PAGE 10 Device type 01 Case outline X Terminal number Terminal symbol 1 +INPUT 2 -VS3 -INPUT 4 OUTPUT 5 +VSFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLU

32、MBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12627 REV PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of

33、 electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrosta

34、tic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer re

35、serves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for t

36、he item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ 2/ 3/ Device manufacturer CAGE code Top side marking Vendor part number V62/12627-01XE 01295 SHN OPA1

37、70ASDRLTEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ For the most current package and ordering information, see the package option addendum at the end of the manufacturers data sheet , or use website . 3/ Pac

38、kage drawings, standard packaging quantities, thermal data, symbolization, and printed circuit board (PCB) design guidelines are available at CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-