DLA DSCC-VID-V62 12648-2013 MICROCIRCUIT LINEAR 50 mA HIGH VOLTAGE MICROPOWER LINEAR REGULATOR MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ Original da

2、te of drawing YY-MM-DD CHECKED BY RAJESH PITHADIA TITLE MICROCIRCUIT, LINEAR, 50 mA, HIGH VOLTAGE, MICROPOWER LINEAR REGULATOR, MONOLITHIC SILICON 13-02-06 APPROVED BY CHARLES F. SAFFLE SIZE A CODE IDENT. NO. 16236 DWG NO. V62/12648 REV PAGE 1 OF 11 AMSC N/A 5962-V102-12 Provided by IHSNot for Resal

3、eNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 50 mA, high voltage, micropower linear regulat

4、or microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering document

5、ation: V62/12648 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Output voltage Circuit function 01 ADP1720 3.3 V 50 mA, high voltage, micropower linear regulator 02 ADP1720 5.0 V 50 mA, high voltage, micropow

6、er linear regulator 03 ADP1720 1.225 V to 5 V 50 mA, high voltage, micropower linear regulator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 8 MO-187-AA Plastic small outline package 1.2.3 Lead finishes. The lead finish

7、es are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1.3 Absolute maximum ratings. 1/ Regulator input supply (IN) to ground (GND) . -0.3 V to +30 V

8、 Regulated output voltage (OUT) to GND . -0.3 V to IN or +6 V (whichever is less) Enable input (EN) to GND -0.3 V to +30 V Adjust (ADJ) to GND -0.3 V to +6 V Storage temperature range (TSTG) -65C to +150C Operating junction temperature range (TJ) -55C to +125C 1.4 Recommended operating conditions. 2

9、/ Operating free-air temperature range (TA) . -55C to +125C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “r

10、ecommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain

11、 no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 3 1.5 Thermal characteristics. Ther

12、mal resistance, junction to ambient (JC) 66C/W Thermal resistance, junction to ambient (JA) 246C/W 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard

13、, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (opti

14、onal) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and

15、table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as sh

16、own in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 4 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VIN= 12 V, IOUT=

17、 100 A, CIN= COUT= 1 F, unless otherwise specifiedTemperature, TA Device type Limits Unit Min Max Input voltage range VIN-55C to +125C 01,02,03 4 28 V Operating supply current IGNDIOUT= 0 A +25C 01,02, 03 28 typical A IOUT= 0 A, VIN= VOUT+ 0.5 V or 4 V (whichever is greater) -55C to +125C 80 IOUT= 1

18、00 A +25C 35 typical IOUT= 100 A, VIN= VOUT+ 0.5 V or 4 V (whichever is greater) -55C to +125C 120 IOUT= 1 mA +25C 74 typical IOUT= 1 mA, VIN= VOUT+ 0.5 V or 4 V (whichever is greater) -55C to +125C 340 IOUT= 10 mA +25C 300 typical IOUT= 10 mA, VIN= VOUT+ 0.5 V or 4 V (whichever is greater) -55C to

19、+125C 900 100 A IOUT 50 mA, VIN= VOUT+ 0.5 V or 4 V (whichever is greater) -55C to +125C 2115 Shutdown current IGND-SDEN = GND +25C 01,02, 03 0.7 typical A -55C to +125C 1.7 Output. Fixed output VOUTIOUT= 100 A +25C 01,02 -0.5 +0.5 % Voltage accuracy 100 A IOUT 50 mA +25C 01,02 -1 +1 % -55C to +125C

20、 -2 +2 Adjustable output 2/ VOUTIOUT= 100 A +25C 03 1.2188 1.2311 V Voltage accuracy 100 A IOUT 50 mA +25C 03 1.2127 1.2372 V -55C to +125C 1.2005 1.2495 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARI

21、TIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 5 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VIN= 12 V, IOUT= 100 A, CIN= COUT= 1 F, unless otherwise specifiedTemperature, TA Device type Limits Unit Min Max Output continued. Noise

22、OUTNOISEVOUT= 1.6 V, COUT= 1 F +25C 01,02, 03 146 typical Vrms (10 Hz to 100 kHz) VOUT= 1.6 V, COUT= 10 F 124 typical VOUT= 5 V, COUT= 1 F 340 typical VOUT= 5 V, COUT= 10 F 266 typical Regulation. Line regulation VOUT/ VINVIN= (VOUT+ 0.5 V) to 28 V -55C to +125C 01,02,03 -0.02 +0.02 %/V Load regulat

23、ion 3/ VOUT/ 1 mA IOUT 50 mA +25C 01,02, 03 0.001 typical %/mA IOUT-55C to +125C 0.005 Dropout voltage 4/ VDROPOUTIOUT= 10 mA +25C 01,02,03 55 typical mV -55C to +125C 105 IOUT= 50 mA +25C 275 typical -55C to +125C 480 Start up time 5/ tSTARTUP+25C 01,02,03 200 typical s Current limit 6/ threshold I

24、LIMIT+25C 01,02,03 55 140 mA Thermal characteristics. Thermal shutdown threshold TSSDTJrising +25C 01,02,03 150 typical C Thermal shutdown hysteresis TSSD-HYSTJrising +25C 01,02,03 15 typical C See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

25、t license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions VIN= 12 V, IOUT= 100 A, CIN= COUT= 1 F, unless otherwise specifiedTemperature, TA Device type Limi

26、ts Unit Min Max Enable (EN) characteristics. Enable input logic high VIH4 V VIN 28 V +25C 01,02,03 1.8 V Enable input logic low VIL4 V VIN 28 V +25C 01,02,03 0.4 V Enable input leakage current VI-LEAKAGEEN = GND +25C 01,02, 03 1 A EN = IN 1 Adjust input bias current ADJI-BIAS+25C 01,02,03 100 nA Pow

27、er supply rejection ratio PSRR f = 120 Hz, VIN= 8 V, VOUT= 1.6 V +25C 01,02, 03 -90 typical dB f = 1 kHz, VIN= 8 V, VOUT= 1.6 V -80 typical f = 10 kHz, VIN= 8 V, VOUT= 1.6 V -60 typical f = 120 Hz, VIN= 8 V, VOUT= 5 V -83 typical f = 1 kHz, VIN= 8 V, VOUT= 5 V -70 typical f = 10 kHz, VIN= 8 V, VOUT=

28、 5 V -50 typical 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In th

29、e absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Accuracy when OUT is connected directly to ADJ. When OUT voltage is set by external feedback resistors, absolute accuracy in adjust mode depends on the tolerances of resistors used. 3/ Base

30、d on an end point calculation using 1 mA and 50 mA loads. See figure 3 for typical load regulation performance for loads less than 1 mA. 4/ Dropout voltage is defined as the input to output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output

31、 voltages above 4 V. 5/ Start up time is defined as the time between the rising edge of EN to OUT being at 95% of its nominal value. 6/ Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 5.0

32、V output voltage is defined as the current that causes the output voltage to drop 90% of 5.0 V, or 4.5 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 7 Ca

33、se X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 8 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A - .043 - 1.10 A1

34、.029 .037 0.75 0.95 A2 .001 .005 0.05 0.15 b .009 .015 0.25 0.40 c .003 .009 0.09 0.23 D .110 .125 2.80 3.20 E .110 .125 2.80 3.20 E1 .183 .202 4.65 5.15 L .015 .031 0.40 0.80 NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Falls within reference to

35、JEDEC MO-187-AA. FIGURE 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 9 Device types 01, 02 03 Case outline X X Terminal number

36、 Terminal symbol 1 GND ADJ 2 IN IN 3 OUT OUT 4 EN EN 5 GND GND 6 GND GND 7 GND GND 8 GND GND Terminal number Terminal symbol Description 1 GND Device types 01 and 02. Fixed output voltage option. This pin is internally connected to ground. 1 ADJ Device type 03. Adjustable output voltage option. A re

37、sistor divider from OUT to ADJ sets the output voltage. 2 IN Regulator input supply. Bypass IN to GND with a 1 F or greater capacitor. 3 OUT Regulator output voltage. Bypass OUT to GND with a 1 F or greater capacitor. 4 EN Enable input. Drive EN high to turn on the regulator; drive it low to turn of

38、f the regulator. For automatic startup, connect EN to IN. 5 GND Ground. 6 GND Ground. 7 GND Ground. 8 GND Ground. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT N

39、O. 16236 DWG NO. V62/12648 REV PAGE 10 FIGURE 3. Output voltage versus load current. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/12648 REV PAGE 11 4. VERIFICATION 4.1 Pr

40、oduct assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensi

41、tive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sen

42、sitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes a

43、re provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of suppl

44、y at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Transportation package Vendor part number V62/12648-01XE 24355 Tube ADP1720TRMZ3.3-EP Reel ADP1720TRMZ3.3-EP-R7 V62/12648-02XE 24355 Tube ADP1720TRMZ5-EP Reel ADP

45、1720TRMZ5-EP-R7 V62/12648-03XE 24355 Tube ADP1720TRMZ-EP Reel ADP1720TRMZ-EP-R7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 24355 Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Raheen Business Park Limerick, Ireland Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-