DLA DSCC-VID-V62-04745-2005 MICROCIRCUIT LINEAR LOW POWER LOW OFFSET DUAL VOLTAGE COMPARATORS MONOLITHIC SILICON《微型电路 线形 低功率 低偏移 四倍电压比较器 单块硅》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-

2、MM-DD CHECKED BY TOM HESS APPROVED BY RAYMOND MONNIN TITLE MICROCIRCUIT, LINEAR, LOW POWER, LOW OFFSET, DUAL VOLTAGE COMPARATORS, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/04745 05-03-08 REV PAGE 1 OF 14 AMSC N/A 5962-V030-05 Provided by IHSNot for ResaleNo reproduction or networki

3、ng permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low power, low offset, dual voltage comparators microcircuit, wi

4、th an operating temperature range of -40C to +85C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/04745 - 0

5、1 X A Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 LM2903EP Low power, low offset, dual voltage comparators 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Numb

6、er of pins JEDEC PUB 95 Package style X 8 MS-012-AA Plastic small outline Y 8 MS-001-BA Plastic dual in line Z 8 See figure 1 Micro SMD ball grid array 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Materi

7、al A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 3 1.3 A

8、bsolute maximum ratings. 1/ Supply voltage (+V) . 36 V Differential input voltage 36 V 2/ Input voltage -0.3 V to +36 V Input current (VIN -0.3 V dc) . 50 mA 3/ Power dissipation (PD) : 4/ Case X (small outline package) 510 mW Case Y (molded dual in line package) 780 mW Output short circuit to GND C

9、ontinuous 5/ Operating temperature range (TA) . -40C to +85C Storage temperature range (TSTG) . -65C to +150C Soldering information: Case X (vapor phase, 60 seconds) 215C (infared, 15 seconds) . 220C Case Y (soldering, 10 seconds) . 260C Electrostatic discharge (ESD) rating (1.5 k in series with 100

10、 pF) . 1300 V 1.4 Recommended operating conditions. 6/ Operating temperature range (TA) -40C to +85C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other c

11、onditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Positive excursions of input voltage may exceed the power supply level. As long as other voltage remains with

12、in the common mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -0.3 V dc (or 0.3 V below the magnitude of the negative power supply, if used). 3/ This input current will only exist when the voltage at any of the input leads is driven ne

13、gative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages

14、 of the comparators to go to the +V voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than -0.3 V d

15、c. 4/ For operating at high temperatures, the device must be derated based on a 125C maximum junction temperature and a thermal resistance of 170C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The low bias dissipation and the “ON OFF” character

16、istic of the outputs keeps the chip dissipation very small (PD 100 mW), provided the output transistors are allowed to saturate. 5/ Short circuits from the output to +V can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is appr

17、oximately 20 mA independent of the magnitude of +V. 6/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot f

18、or ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copi

19、es should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manu

20、facturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating condi

21、tions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.

22、2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAG

23、E 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions +V = 5 V unless otherwise specifiedTemperature, TA Device type Min Max Unit Input offset voltage VIO2/ +25C 01 7.0 mV 2.0 typical Input bias current IIBIIN(+)or IIN(-)with output in linear range, +25C 01 250 nA VCM

24、= 0 V 3/ 25 typical Input offset current IIOIIN(+)- IIN(-), +25C 01 50 nA VCM= 0 V 5 typical Input common mode voltage range VCMR+V = 30 V dc 4/ +25C 01 0 +V 1.5 V Supply current I RL= , +V = 5 V +25C 01 1.0 mA 0.4 typical RL= , +V = 36 V 2.5 1.0 typical Voltage gain RL 15 k, +V = 15 V, +25C 01 25 V

25、/mV VO= 1 V to 11 V 100 typical Large signal response time VIN= TTL logic swing, RL= 5.1 k, VREF= 1.4 V, VRL= 5 V +25C 01 300 typical ns Response time VRL= 5 V, RL= 5.1 k 5/ +25C 01 1.5 typical s Output sink current ISINKVIN(-)= 1 V, VIN(+)= 0 , +25C 01 6.0 mA VO 1.5 V 16 typical Saturation voltage

26、VSATVIN(-)= 1 V, VIN(+)= 0 , +25C 01 400 mV ISINK 4 mA 250 typical Output leakage current VIN(+)= 1 V, VIN(-)= 0 , VO= 5 V +25C 01 0.1 typical nA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, CO

27、LUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions +V = 5 VTemperature, TA Device type Min Max Unit Input offset voltage VOS2/ -40C TA +85C 01 15 mV 9 typical Input offset current

28、IOSIIN(+)- IIN(-), -40C TA +85C 01 200 nA VCM= 0 V 50 typical Input bias current IIBIIN(+)or IIN(-)with output in linear range, -40C TA +85C 01 500 nA VCM= 0 V 3/ 200 typical Input common mode voltage range VCMR+V = 30 V 4/ -40C TA +85C 01 0 +V 2.0 V Saturation voltage VSATVIN(-)= 1 V, VIN(+)= 0 , -

29、40C TA +85C 01 700 mV ISINK 4 mA 400 typical Output leakage current VIN(+)= 1 V, VIN(-)= 0 , VO= 30 V -40C TA +85C 01 1.0 A Differential input voltage Keep all VINs 0 V (or V, if used) 6/ -40C TA +85C 01 36 V 1/ Testing and other quality control techniques are used to the extent deemed necessary to

30、assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design.

31、2/ At output switch point, VO= 1.4 V, RS= 0 with +V from 5 V to 30 V; and over the full input common mode range ( 0 V to +V 1.5 V ), at 25C. 3/ The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output

32、 so no loading change exists on the reference or input lines. 4/ The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common mode voltage range is +V 1.5 V at 25C, but either or both inputs can go to +36 V without

33、damage independent of the magnitude of +V. 5/ The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance characteristics section. 6/ Positive excursions of input voltage may exceed the power supply level. As lo

34、ng as the other voltage remains within the common mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -0.3 V (or 0.3 V below the magnitude if the negative power supply, if used). Provided by IHSNot for ResaleNo reproduction or networking p

35、ermitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 7 Case X FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUM

36、BUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 8 Case X Dimensions Inches Millimeters Symbol Min Max Min Max A .053 .069 1.35 1.75 A1 .004 .010 0.10 0.25 b .0138 .0200 0.35 0.51 c .0075 .0098 0.190 0.248 D .189 .197 4.8 5.0 e .050 nominal 1.27 nominal E .150 .158 3.81 4.01

37、 E1 .228 .244 5.8 6.2 L .016 .050 0.41 1.27 L1 .041 - 1.04 - n 8 leads 8 leads NOTE: 1. Controlling dimensions are millimeters, inch dimensions are given for reference only. 2. Fall within JEDEC MS-012-AA. FIGURE 1. Case outlines- Continued. Provided by IHSNot for ResaleNo reproduction or networking

38、 permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 9 Case Y FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY

39、 CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 10 Case Y Dimensions Inches Millimeters Symbol Min Max Min Max A .145 .200 3.683 5.080 A1 .020 - 0.508 - b .015 .021 0.381 0.533 c .009 .015 0.229 0.381 D .373 .400 9.474 10.16 e .090 .110 2.286 2.794 E .245 0.25

40、5 6.223 6.477 E1 .280 - 7.112 - E2 .310 .365 7.874 9.271 L .125 .140 3.175 3.556 n 8 leads 8 leads NOTE: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. Falls within JEDEC MS-001-BA. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo repro

41、duction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 11 Case Z FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

42、IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 12 Case Z Dimensions Inches Millimeters Symbol Min Max Min Max A 0.023 - 0.600 - A1 0.002 0.005 0.050 0.125 A2 0.008 0.010 0.215 0.265 b 0.012 0.013 0.305 0.335 D/E 0.060 - 1.514 - e 0.020 n

43、ominal 0.500 nominal n 8 leads 8 leads NOTE: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS

44、COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 13 Device type 01 Case outlines X and Y Terminal number Terminal symbol 1 OUTPUT A 2 INVERTING INPUT A (-) 3 NON-INVERTING INPUT A (+) 4 GND 5 NON-INVERTING INPUT B (+) 6 INVERTING INPUT B (-) 7 OUTPUT B 8 +VDevice type 01 Case ou

45、tline Z Terminal number Terminal symbol A1 OUTPUT A A2 V+ A3 OUTPUT B B1 INVERTING INPUT A B3 INVERTING INPUT B C1 NON-INVERTING INPUT A C2 GND C3 NON-INVERTING INPUT B FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D

46、EFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04745 REV PAGE 14 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedure

47、s should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein i