DLA MIL-B-18 31 E-2010 BATTERY DRY BA-65.pdf

1、AMSC N/A FSC 6135 INCH-POUND MIL-B-18/31E 22 November 2010 SUPERSEDING MIL-B-18/31D 21 May 1985 MILITARY SPECIFICATION SHEET BATTERY, DRY, BA-65 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described h

2、erein shall consist of this specification sheet and MIL-B-18. FIGURE 1. Battery dimensions. INACTIVE FOR NEW DESIGN AFTER 6 FEBUARY 2002 AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-18/

3、31E 2 Ltr Inches mm Min Max Min Max A .495 .505 12.57 12.83 B .745 .755 18.92 19.18 C 1.308 1.318 33.22 33.48 D 2.620 2.630 66.55 66.80 E 1.308 1.318 33.22 33.48 F 2.620 2.630 66.55 66.80 G .433 .443 11.00 11.25 H 3.688 4.313 93.68 109.47 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are

4、 given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .02 (0.5 mm) for two place decimals. 4, Square, diagonal, or round corners are optional. 5. Socket type I is required. (see MIL-B-18 for details.) 6. Voltage markings may be

5、 placed either on the top or front face of the battery. 7. Marking to be in accordance with MIL-B-18. FIGURE 1. Battery dimensions - Continued. REQUIREMENTS: Dimensions, marking, and configuration: See figure 1. Nominal voltage: 1.5 volts. Usual number and type of cells: 4 “F” cells Usual cell conne

6、ction: Parallel. Terminals: 2-hole socket. Weight (maximum): 1 pound, 8 ounces. Capacity tests: When the battery is tested in accordance with the methods of examination and test of this specification, the minimum capacity-test requirements shall be not less than the minimum time specified for SLD or

7、 SLT. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-18/31E 3 First article inspection in accordance with MIL-B-18: Visual and mechanical (external). Battery voltage. Vibration test. Mechanical-shock test in accordance with MIL-STD-202, method

8、 213, test condition I. Insulation resistance test in accordance with MIL-STD-202, method 302, test condition B, tolerance 20 volts. Capacity, D (without storage). Jacket integrity test. Conformance inspection in accordance with MIL-B-18: Visual and mechanical (external). Battery voltage. Insulation

9、-resistance test in accordance with MIL-STD-202, method 302, test condition B, tolerance 20 volts. Vibration test. Mechanical-shock test in accordance with MIL-STD-202, method 213, test condition I. Jacket integrity test. Electrolyte leakage. Capacity, D and T. Method of examination and test: Capaci

10、ty tests: See requirements for capacity specified herein. Storage: Test Period D 12 months T 90 days Discharge: The battery shall be discharged through 5 ohms for 2 periods or 1 hour each daily. The intervals between discharge periods shall be 6 hours and 16 hours, respectively. This cycle shall be

11、repeated continuously to a test-end voltage of 0.9 volt. Closed circuit voltage: Use TS-183 ( )/U test per special marking or, with minimum permissible voltage as specified for TS-183 ( )/U, use a load resistance value of 1.998 ohms. Special marking on each unit package: TO TEST THIS BATTERY WITH TS

12、-183 ( )/U: USE JACK NO. MINIMUM PERMISSIBLE VOLTAGE 1 1.40 Unless expressly authorized, this test information shall apply to Army and Air Force applications only. Part or Identifying Number (PIN): BA-65, see 1.2 of MIL-B-18. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

13、ut license from IHS-,-,-MIL-B-18/31E 4 Reference documents. In addition to MIL-B-18, this document references the following: MIL-STD-202 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only a

14、nd the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: P

15、reparing activity: Army - CR DLA - CC Navy - SH DLA - CC (Project 6135-2010-051) Review activities: Army - MI Navy - MC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-