DLA MIL-B-44152 C (1)-1994 BOOTS COMBAT MILDEW& WATER RESISTANT DMS《DMS防水防霉战斗靴》.pdf

1、 1 MIL-B-44152C AMENDMENT 1 14 October 1994 MILITARY SPECIFICATION BOOTS, COMBAT; Mildew distribution is unlimited. 1 of 5 Licensed by Information Handling ServicesMIL-B-44152C AMENDMENT 1 PAGE 10 3.3.12, Removable cushion insert, last sentence: Delete the sentende in its entirety and substitute “T

2、he total thickness of the insole (insert) shall be 0.155 to 0.195 inch forward of the instep arch and 0.190 inch to 0.215 inch elsewhere (see 6.9).“ r PAGE 11 3.3.12, after line 12, add the following footnote: “2 - Less than 10% after 5 hours exposure to saturated steam at 15 psi.“ 3.5.1, Stitched u

3、ppers, line 1: Delete “stitched“. 3.5.1, Stitched uppers, line 2: After the words l*1/2 size“ add “and/or one full width“. PAGE 18 3.8.6, Lastinq, line 12: Delete Itnot more than 3/4 inch“ and substitute “any excess lasting allowance margin, due to stretchy leather not permitting a proper heel seat

4、bottom closure, shall be trimmed.“ following new paragraph: 3.8.6.2, Counter size schedule: After this paragraph add the “3.8.6.2.1 Alternative counter assembly. As an alternate, an unmolded counter, well cemented on both sides, shall be assembled in accordance with the counter size schedule (see 3.

5、8.6.2) so that they fill the counterpockets. appropriate shaped molds on the back part molding machine. The counter shall be turned over the last at the bottom 1/2 2 1/16 inch. Although not a requirement, the counter may be seated to the insole with one or two tacks near the back end of the counter

6、flange. If tacks are used, they shall be driven through the outside counterpocket and insole and clinched against the heel seat plate. lasting operations. Commencing with the conditioning and insertion of the box toe, the remainder of the lasting procedure is as the standard method. It The counter a

7、nd upper shall be formed and flanged using Steel tacks may be used for t 2 of 5 Licensed by Information Handling ServicesMIL-B-44152C AMENDMENT 1 PAGE 21 3.8.15.1, Preparation: After this paragraph add the following note: “NOTE: Upon occasion when some insignificant thread ends are noted during insp

8、ection (audit) they will not be cause for lot/shipment rejection. Inplant corrective action shall be made on current and future production. I PAGE 28 4.4.1 Component and material inspection, end of paragraph: At the end of this paragraph add the following information: “A certificate of compliance sh

9、all be submitted and will be accepted for the stated testing and inspection requirements contained in the component specification for the following components: Component Paragraph Number Collar leather Leather insole Counters Backseam tape Vamp lining Shank Heel filler Thread Laces 3.3.1.3 3.3.1.4 3

10、3.2 3.3.3.1 3.3.3.2 3.3.6.1, add footnote 2 to each requirement in Table VI 3.3.8, add the requirement listed above 3.3.9 3.3.14 In addition to the certificate of compliance, a laboratory test report shall be provided with each component lot/shipment from each supplier for prime contractor records

11、and verification by the Government, when testing/inspection is deemed necessary) on all components covered by a “certificate of compliance“. 4.4.2.2 In-process examinatioii of uppers after all fittinq, Delete the last sentence in its entirety and substitute the following: “The inspection level shal

12、l be II, and the Acceptable Quality Level (AQL), shall be 1.0. 3 of 5 Licensed by Information Handling ServicesMIL-B-44152C (1) 9999906 1992664 041 MIL-B-44152C AMENDMENT 1 PAGE 29 4.4.2.2, In-process examination of uppers after all fittinas, under “Classification“, line 26: Delete “107“ and substit

13、ute “*I. PAGE 30 I 4.4.2.4 In-Drocess examination of boot before last pulling, , Delete the last sentence in its entirety and substitute the following: I “The inspection level shall be II, and the Acceptable Quality Level (AQL), shall be 1.0.“ PAGE 31 4.4.3 End item visual examination, sentence 4: D

14、elete in its entirety and substitute the following: “The inspection level shall be II, and the AQL shall be 1.0.“ 4.4.3, End item visual examination: At the end of the paragraph, add the following new sentence: “Upper leather grain-break is not to be determined by flexing of the component; only a be

15、nding inward of the grain surface, as would occur thru use of the “Satraii scale is required. I delete “5“ and substitute “6“. 4.4.3, End item visual examination, sub-paragraph a, line 8, 4.4.3, End item visual examination, NOTE: Delete the NOTE paragraph in its entirety and substitute the following

16、 “NOTE: visible at a distance of 3 feet or more and it appreciably affects item appearance. II Appearance defects shall be scored when the condition is plainly PAGE 32 4.4.3, End item visual examination, Defects table: Under “Color and finish“, delete “not specified color“ and substitute “color not

17、 within the specified range of color“ 4 of 5 Licensed by Information Handling ServicesMIL-B-44152C (1) 9 999990b i1992665 T MIL-B-44152C AMENDMENT 1 PAGE 32 4.4.3, End item visual examination, Defects table: Under “Design, type, and style Upper leather“, delete lines 5 through 7 and substitute: Any

18、grub/tick damage, scratches, brands, or bony leather, fat wrinkles, flanky leather, course grain or veins etc., that appreciably affects appearance/serviceability(*)“ Delete “112“ and substitute “*“ . PAGE 35 4.4.3, End item visual examination, Defects table: Under “Outersole including heel“, delete

19、 “thickness not as specified as in drawing“ and substitute “thickness less than specified or more than 1/32 inch greater than specified“ . 4.4.3, End item visual examination, Defects table: Under “Outersole including heel“, between defects 131 and 226, add the following new defect: II “Thickness gre

20、ater than specified but not more than 1/32 inch greater than specified 2 2 5A“ PAGES 32-36 4.4.3, End item visual examination, Defects table: Under “Classification“ , delete “Major“ and substitute “Minor“. Custodians: Army - GL Navy - NU Air Force - 99 Review Activities: Preparing Activity: DLA - CT Project No. 8430-0433 Army - MD Navy - MC Air Force - 45, 82 5 of 5 Licensed by Information Handling Services