DLA MIL-B-44332-1988 BAG CARRYING PROTECTIVE SUIT EXPLOSIVE ORDINANCE DEVICE (EOD)《易爆装置警卫队服装备袋》.pdf

1、MIL-B-44332 89 7777906 0403283 7 5 - /5- 43 12 April 1988 MILITARY SPECIFICATION BAG, CARRYING, PROTECTIVE SUIT, EXPLOSIVE ORDINANCE DEVICE (EOD) This specification is approved for use by the U.S. Army Natick Research, Development, and Engineering Center, Department of the Army, and is available for

2、 use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope, This document covers a carrying/storage bag fabricated from Olive Green 106 nylon duck and Olive Drab 7 nylon webbing with a slide fastener closure. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specific

3、ations, standards, and handbooks. The following Specifications, standards, and handbooks form a part of this speci,cation to the extent specified herein. Unless otherwise specif ied, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications

4、 and Standards (DODISS) and supplement thereto, cited in the Solicitation. . SPECIFICATIONS FEDERAL PPP-B-636 - Boxes, Shipping, Fiberboard MI LI TARY MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For Bene

5、ficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S, Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement

6、 Proposal (DD Form 1426) appearing at the end of this document or by letter. I AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; d-istribution is unlimited. f THIS DOCUMENT CONTAINS / I- PAGES. _ Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

7、nse from IHS-,-,-MIL-B-44332 8L-I m 777770b 0403284 O m STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 -

8、Quality of Wood Members for Containers and Pallets 9: 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issiies shall be

9、those in effect on the date of the solicitation. DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2-3-468 - Bag, Carrying; Protective Suit, Explosive Ordinance 2-3-469 - Body Piece “A“ 2-3-470 - Body Piece “B“ 2-3-471 - Flap Device (EOD) (Copies of documents required by contra

10、ctors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 9: 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the is

11、sues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitatio

12、n. AMERICAN SOCIETY FOR. TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents a

13、re generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-44332 4 m 9777706 0403285 2 m :c 2.3 Order of precedence. In th

14、e event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3

15、.1 Guide samples. Guide samples, when furnished, are solely for guidance and information (see 6.3). Variation from the document may appear in the sample, in which case the document shall govern. 3.2 First article, When specified in the contract or purchase order, a sample shall be subjected to first

16、 article inspection (see 4.3, 6.2, and 6.4). 3.3 Materials. The materials shall be as specified on Drawing 2-3-468 and all subsidiary drawings and parts lists pertaining thereto (see 6.5). 3.4 Construction. The construction shall conform in all respects to the drawings listed in section 2 and as spe

17、cified herein. 3.4.1 Stitches, seams, and stitchings. All stitches, seams, and stitching shall conform to FED-STD-751. The type of seam, stitching and stitches per inch shall be as specified on referenced drawings. Seam allowances shall be maintained with seams sewn so that no raw edges, run-Offs, t

18、wists, pleats, puckers, or open seams occur. 3.4.1.1 Type 301 stitchin edge not folded or not stitched as indicated on drawing. as specified. End of carrying handle not finished Misplaced or not properly attached, failing to serve intended purpose. Omitted, illegible, incorrect, misplaced, or size c

19、haracters not as specified. Marking not specified color. X X X X X Slider jams or fails to interlock chain; tapes improperly applied, causing malfunction. X pulls or not formed as specified. X Thongs not secured to stirrup Grease, oil, or ink stain clearly noticeable; thread ends not trimmed through

20、out. X 4.4.4 End item dimensional examination. The end items shall be examined for conformance to the dimensions annotated with an asterisk (*) on Drawing 2-3-468. Any dimension not within the specified tolerance shall be classified as a defect. The lot size shall be expressed in units of bags. The

21、sample unit shall be one bag. The inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 10.0. 4.4.5 Packaging examination. The fully packaged end items shall be examined for the defects listed below. The lot size shall be expressed in units of shipping

22、containers. The sample unit shall be one shipping container fully packaged. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-B-44332 L

23、( 9997906 0403291 - S MIL-B-44332(GL) Examine Defect Marking (exterior Omitted; incorrect; illegible; of improper size, and interior) location, sequence, or method of application. Ma ter ia 1 s Any component missing, damaged, or not as specified. Workmanship Contents Inadequate application of compon

24、ents, such as: incomplete sealing or closure of flap, improper taping, loose strapping, or inadequate stapling. Bulged or distorted container. Number of bags per shipping container is more or less than required. 4.4.6 Palletization examination. The fully packaged and palletized end items shall be ex

25、amined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load fully packaged. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Exam i ne Defect Fin

26、ished dimensions Length, width, or height exceeds specified maximuin requir.ement. Palletization Pallet pattern not as specified. Interlocking of loads not as specified, Load not bonded with required straps as specified. Weight Exceeds maximum load 1 imi ts . Marking Omitted; incorrect; illegible; o

27、f improper size, location, sequence, or method of application. 5. PACKAGING 5.1 Preservation. Preservation shall be level A or Commercial as specified (see 6.2). 5.1.1 Level A. Each bag shall be laid flat and folded once with the bottom to the handles, and then folded twice from side to side, yieldi

28、ng a folded bag size of approximately 11 by 12 inches. 5.1.2 Commercial. Bags shall be preserved in accordance with ASTM D 3951. 5.2 Packing. Levels A, B, or Commercial as specified (see 6.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ _ _ - M

29、IL-B-4Lt332 4 7777706 0403272 T W 5.2.1 Level A packing. Twenty bags, preserved as speciied in 5.1, shall be packed in a snug-fitting fiberboard container conforming to style RSC-L, grade V2s of PPP-B-636. The inside of each shipping container shall be fitted with a box liner conforming to type CF,

30、class weather-resistant, variety DW, grade V15c of PPP-13-636. Bags shall be packed two in length, one in width, and ten in depth. Approximate dimensions of each shipping container shall be 22 inches in length by 12 inches in width by 12 inches in depth. Approximate dimensions are furnished as a gui

31、de only. Each shipping container shall be closed in accordance with method III, waterproofed in accordance with method V, and reinforced as specified in the appendix of PPP-E-636, except that the inspection shall be in accordance with 44.5. Shipping containers shall be arranged in unit loads in acco

32、rdance with MIL-L-35078 for the type and class of load specified (see 6.2). 5.2.2 Level B packing. Twenty bags, preserved as specified in 5.1, shall be packed in a snug-fitting fiberboard container conforming to style RSC-L, type CF (variety CEr) or type SF, class domestic, grade 200 af PPP-B-636. T

33、he inside of each shipping container shall be fitted with a box liner conforming to type CF, class domestic, variety DW, grade 200 of PPP-B-636. Bags shall be packed two in length, one in width, and ten in depth. Approximate inside dimensions of each shipping container shall be 22 inches in length b

34、y 12 inches in width by 12 inches in depth. Approximate dimensions are furnished as a guide only. Each shipping container.shal1 be closed in accordance with method IT as specified in the appendix of PPP-B-636, except that the inspection shall be in accordance with 4.4.5, 5.2.2.1 Weather-resistant fi

35、berboard containers. When specif ied (see 6.21, the shipping container shall be a grade VC, VS., or V4s fiberboard box fabricated in accordance with PPP-B-636 and closed in accordance with method III , as specified in the appemdix of PPP-B-636, except that the inspection shall be in accordance with

36、4.4.5. 5.2.3 Commercial packing. Bags, preserved as specified in 5.1, shall be packed in accordance with ASTM D 3951. 5.3 Palletization. When specified (see 6.2), bags, packed as specified in 5.2.2 and 5.2.3 shall be palletized on a four-way entry pallet in accordance with load type Ia of MIL-STD-14

37、7. entry), type IV, or type V in accordance with MIL-STD-147. Pallets shall be fabricated from wood groups I, II, III, or IV of MIL-STD-731. Each prepared load shall be bonded with primary and secondary straps in accordance with bonding means K and L or film bonding means Q or P. Pallet pattern shal

38、l be number 35 in accordance with the appendix of MIL-STD-147. Interlocking of loads shall be effected by reversing the pattern of each course. Pallet types shall be type I (four-way 5.4 Marking. purchase order, shipping containers and palletized loads shall be marked in accordance with MIL-STD-129

39、or ASTM D 3951, as applicable. In addition to any special marking required by the contract or 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-y- MIL-B-44332 4 W 9777706 0403273 L - 6. NOTES 6.1 Intended use. The bag is intended for carrying and st

40、oring the explosive ordinance device protective suit. 6.2 Ordering data. Acquisition documents should specify the following: a. Title, number, and date of this document. b. When a first article is required (see 3.2, 4.3, and 6.4). c. d. e. When weather-resistant grade fiberboard shipping containers

41、are f. When palletization is required (see 5.3). Selection of applicable levels of preservation and packing (see 5.1 Type and class of unit load required (see 5.2.1). and 5.2): required for level B packing (see 5.2.2.1). 6.3 Samples. For access to samples, address the contracting office issuing the

42、invitation for bids. 6.4 First article. When a first article is required, it shall be inspected and approved under the appropriate provisions of FAR 52.209. The first article should be a preproduction sample. The contracting officer should specify the appropriate typ.e of first article and the numbe

43、r of units to be furnished. The contracting officer should include specific instructions in all acquisition instruments regarding arrangements for selection, inspection, and approval of the first article. 6.5 Recycled material. It is encouraged that recycled material be used when practical as long a

44、s it meets the requirements of this document (see 3.3). 6.6 Subject term (key word) listing. Bag Carrying bag EOD Protective suit Custodian: Army - GL Preparing activity: Army - GL Project No. 8465-0978 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-