DLA MIL-C-18312 2 D-2013 CAPACITORS FIXED METALLIZED (PAPER-PLASTIC OR PLASTIC FILM) DIELECTRIC DIRECT CURRENT (HERMETICALLY SEALED IN METAL CASES) STYLE CH09 [Use DLA MIL-PRF-3902.pdf

1、AMSC N/A FSC 5910 INCH-POUND MIL-C-18312/2D 28 February 2013 SUPERSEDING MIL-C-18312/2C 27 August 2001 MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, METALLIZED (PAPER-PLASTIC, OR PLASTIC FILM) DIELECTRIC, DIRECT CURRENT (HERMETICALLY SEALED IN METAL CASES), STYLE CH09 This specification sheet is a

2、pproved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-C-18312. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Se

3、e table I for additional dimensions. 4. Number 24 AWG wire for case diameters of .227 inch (5.77 mm) and under. Number 22 AWG for case diameters .267 inch (6.78 mm) thru .344 inch (8.74 mm) and 20 AWG wire for case diameters .432 inch (10.97 mm) and over. 5. Plastic insulating sleeve shall be transp

4、arent. Marking shall be applied to the capacitor case. 6. Plastic insulating sleeve shall extend beyond the capacitor body, but shall not exceed .062 inch (0.79 mm) on either end. Insulating sleeve thickness shall not exceed .016 inch (0.41 mm). FIGURE 1. Style CH09 capacitors. INACTIVE FOR NEW DESI

5、GN, AFTER 8 JANUARY 1970. USE MIL-PRF-39022/1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-18312/2D 2 REQUIREMENTS: Dimensions: See and table I. TABLE I. Characteristics. Part or Identifying Number (PIN) 1/ DC rated voltage (volts) Capacita

6、nce value (F) Circuit diagram Dimensions, nominal (inches) 2/ 3/ Superseded MIL-C-18312/1A and MIL-C-18312/2A Capacitance tolerance L .062 D +.031 -.051 5% 10% CH09A1RA183- 50 0.018 1 .750 .175 0301 0302 CH09A3RA183- 50 0.018 3 .688 .175 0303 0304 CH09A1RA223- 50 0.022 1 .750 .175 0305 0306 CH09A3RA

7、223- 50 0.022 3 .688 .175 0307 0308 CH09A1RA273- 50 0.027 1 .750 .175 0309 0310 CH09A3RA273- 50 0.027 3 .688 .175 0311 0312 CH09A1RA333- 50 0.033 1 .750 .175 0313 0314 CH09A3RA333- 50 0.033 3 .688 .175 0315 0316 CH09A1RA393- 50 0.039 1 .750 .195 0317 0318 CH09A3RA393- 50 0.039 3 .688 .195 0319 0320

8、CH09A1RA473- 50 0.047 1 .750 .195 0321 0322 CH09A3RA473- 50 0.047 3 .688 .195 0323 0324 CH09A1RA563- 50 0.056 1 .750 .235 0325 0326 CH09A3RA563- 50 0.056 3 .688 .235 0327 0328 CH09A1RA683- 50 0.068 1 .750 .235 0329 0330 CH09A3RA683- 50 0.068 3 .688 .235 0331 0332 CH09A1RA823- 50 0.082 1 .750 .235 03

9、33 0334 CH09A3RA823- 50 0.082 3 .688 .235 0335 0336 CH09A1RA104- 50 0.100 1 .750 .235 0337 0338 CH09A3RA104- 50 0.100 3 .688 .235 0339 0340 CH09A1RA184- 50 0.180 1 .874 .312 0341 0342 CH09A3RA184- 50 0.180 3 .812 .312 0343 0344 CH09A1RA224- 50 0.220 1 .874 .312 0345 0346 CH09A3RA224- 50 0.220 3 .812

10、 .312 0347 0348 CH09A1RA274- 50 0.270 1 .874 .312 0349 0350 CH09A3RA274- 50 0.270 3 .812 .312 0351 0352 CH09A1RA334- 50 0.330 1 .874 .312 0353 0354 CH09A3RA334- 50 0.330 3 .812 .312 0355 0356 CH09A1RA394- 50 0.390 1 1.125 .312 0357 0358 CH09A3RA394- 50 0.390 3 1.062 .312 0359 0360 CH09A1RA474- 50 0.

11、470 1 1.125 .312 0361 0362 CH09A3RA474- 50 0.470 3 1.062 .312 0363 0364 CH09A1RA564- 50 0.560 1 1.125 .400 0365 0366 CH09A3RA564- 50 0.560 3 1.062 .400 0367 0368 CH09A1RA684- 50 0.680 1 1.125 .400 0369 0370 CH09A3RA684- 50 0.680 3 1.062 .400 0371 0372 CH09A1RA824- 50 0.820 1 1.125 .400 0373 0374 CH0

12、9A3RA824- 50 0.820 3 1.062 .400 0375 0376 CH09A1RA105- 50 1.0 1 1.125 .400 0377 0378 CH09A3RA105- 50 1.0 3 1.062 .400 0379 0380 CH09A1RA155- 50 1.5 1 1.125 .500 0381 0382 CH09A3RA155- 50 1.5 3 1.062 .500 0383 0384 CH09A1RA225- 50 2.2 1 1.125 .562 0385 0386 See footnotes at end of table. Provided by

13、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-18312/2D 3 TABLE I. Characteristics - Continued. PIN 1/ DC rated voltage (volts) Capacitance value (F) Circuit diagram Dimensions, nominal (inches) 2/ 3/ Superseded MIL-C-18312/1A and MIL-C-18312/2A Capacitan

14、ce tolerance L .062 D +.031 -.051 5% 10% CH09A3RA225- 50 2.2 3 1.062 .562 0387 0388 CH09A1RA275- 50 2.7 1 1.375 .562 0389 0390 CH09A3RA275- 50 2.7 3 1.312 .562 0391 0392 CH09A1RA335- 50 3.3 1 1.375 .562 0393 0394 CH09A3RA335- 50 3.3 3 1.312 .562 0395 0396 CH09A1RA395- 50 3.9 1 1.625 .562 0397 0398 C

15、H09A3RA395- 50 3.9 3 1.562 .562 0399 0400 CH09A1RA475- 50 4.7 1 1.875 .562 0401 0402 CH09A3RA475- 50 4.7 3 1.812 .562 0403 0404 CH09A1RA565- 50 5.6 1 1.625 .670 0405 0406 CH09A3RA565- 50 5.6 3 1.562 .670 0407 0408 CH09A1RA685- 50 6.8 1 1.875 .670 0409 0410 CH09A3RA685- 50 6.8 3 1.812 .670 0411 0412

16、CH09A1RA106- 50 10.0 1 1.875 .750 0413 0414 CH09A3RA106- 50 10.0 3 1.812 .750 0415 0416 CH09A1RA126- 50 12.0 1 2.375 .750 0417 0418 CH09A3RA126- 50 12.0 3 2.312 .750 0419 0420 10% 20% CH09A1NC104- 200 0.10 1 .844 .312 0421 0422 CH09A3NC104- 200 0.10 3 .781 .312 0423 0424 CH09A1NC224- 200 0.22 1 1.12

17、5 .312 0425 0426 CH09A3NC224- 200 0.22 3 1.062 .312 0427 0428 CH09A1NC474- 200 0.47 1 1.125 .400 0429 0430 CH09A3NC474- 200 0.47 3 1.062 .400 0431 0432 CH09A1NC105- 200 1.0 1 1.125 .562 0433 0434 CH09A3NC105- 200 1.0 3 1.062 .562 0435 0436 CH09A1NC155- 200 1.5 1 1.844 .562 0437 0438 CH09A3NC155- 200

18、 1.5 3 1.781 .562 0439 0440 CH09A1NC225- 200 2.2 1 1.844 .562 0441 0442 CH09A3NC225- 200 2.2 3 1.781 .562 0443 0444 CH09A1NC335- 200 3.3 1 1.875 .670 0445 0446 CH09A3NC335- 200 3.3 3 1.812 .670 0447 0448 CH09A1NC475- 200 4.7 1 1.875 1.000 0449 0450 CH09A3NC475- 200 4.7 3 1.812 1.000 0451 0452 CH09A1

19、NC685- 200 6.8 1 1.875 1.000 0453 0454 CH09A3NC685- 200 6.8 3 1.812 1.000 0455 0456 CH09A1NC106- 200 10.0 1 2.375 1.000 0457 0458 CH09A3NC106- 200 10.0 3 2.312 1.000 0459 0460 CH09A1NC126- 200 12.0 1 2.625 1.000 0461 0462 CH09A3NC126- 200 12.0 3 2.562 1.000 0463 0464 CH09A1NE473- 400 0.047 1 1.125 .

20、312 0465 0466 CH09A3NE473- 400 0.047 3 1.062 .312 0467 0468 CH09A1NE104- 400 0.10 1 1.125 .400 0469 0470 CH09A3NE104- 400 0.10 3 1.062 .400 0471 0472 CH09A1NE224- 400 0.22 1 1.125 .562 0473 0474 CH09A3NE224- 400 0.22 3 1.062 .562 0475 0476 CH09A1NE474- 400 0.47 1 1.625 .562 0477 0478 See footnotes a

21、t end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-18312/2D 4 TABLE I. Characteristics - Continued. PIN 1/ DC rated voltage (volts) Capacitance value (F) Circuit diagram Dimensions, nominal (inches) 2/ 3/ Superseded MIL-C-18312/1A

22、and MIL-C-18312/2A Capacitance tolerance L .062 D +.031 -.051 10% 20% CH09A3NE474- 400 0.47 3 1.562 .562 0479 0480 CH09A1NE105- 400 1.0 1 1.875 .750 0481 0482 CH09A3NE105- 400 1.0 3 1.812 .750 0483 0484 CH09A1NE225- 400 2.2 1 1.875 1.000 0485 0486 CH09A3NE225- 400 2.2 3 1.812 1.000 0487 0488 CH09A1N

23、E335- 400 3.3 1 2.625 1.000 0489 0490 CH09A3NE335- 400 3.3 3 2.562 1.000 0491 0492 CH09A1NF103- 600 0.01 1 .812 .312 0493 0494 CH09A3NF103- 600 0.01 3 .750 .312 0495 0496 CH09A1NF223- 600 0.022 1 .812 .312 0497 0498 CH09A3NE155- 400 0.022 3 .750 .312 0499 0500 CH09A1NF473- 600 0.047 1 1.125 .400 050

24、1 0502 CH09A3NF473- 600 0.047 3 1.062 .400 0503 0504 CH09A1NF104- 600 0.10 1 1.125 .500 0505 0506 CH09A3NF104- 600 0.10 3 1.062 .500 0507 0508 CH09A1NF224- 600 0.22 1 1.375 .562 0509 0510 CH09A3NF224- 600 0.22 3 1.312 .562 0511 0512 CH09A1NF474- 600 0.47 1 1.625 .670 0513 0514 CH09A3NF474- 600 0.47

25、3 1.562 .670 0515 0516 CH09A1NF105- 600 1.0 1 1.844 1.000 0517 0518 CH09A3NF105- 600 1.0 3 1.781 1.000 0519 0520 CH09A1NF155- 600 1.5 1 1.875 1.000 0521 0522 CH09A3NF155- 600 1.5 3 1.812 1.000 0523 0524 CH09A1NF225- 600 2.2 1 2.625 1.000 0525 0526 CH09A3NF225- 600 2.2 3 2.562 1.000 0527 0528 1/ Comp

26、lete PIN will include an additional symbol for capacitance tolerance. 2/ Dimensions shown are for bare case. (see ). 3/ See table II for metric equivalents. TABLE II. Millimeter equivalents of decimal inches. Inches mm Inches mm Inches mm .031 0.79 .688 17.48 1.562 39.67 .051 1.30 .750 19.05 1.625 4

27、1.28 .062 1.57 .781 19.84 1.781 45.24 .175 4.45 .812 20.62 1.812 46.02 .195 4.95 .844 21.44 1.844 46.84 .235 5.97 .874 22.20 1.875 47.63 .312 7.92 1.000 25.40 2.312 58.72 .400 10.16 1.062 26.97 2.375 60.33 .500 12.70 1.125 28.58 2.562 65.07 .562 14.27 1.312 33.32 2.625 66.68 .670 17.02 1.375 34.93 P

28、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-18312/2D 5 Case material: Nonmagnetic (end seals may be of magnetic material). Capacitance value: See table I. Capacitance tolerance: See table I. DC rated voltage: See table I. Seal: Method 112 of

29、 MIL-STD-202, condition A. Liquid-filled capacitors: One hour at applicable high ambient temperature 3C with no evidence of leakage. Dielectric withstanding voltage: Method 301 of MIL-STD-202. Terminal to terminal: 200 percent of rated dc voltage. Terminal to case (where case not a terminal): 200 pe

30、rcent of rated dc voltage. Capacitance: Method 305 of MIL-STD-202 (for value and tolerance see table I). Dissipation factor: At 25C: 1.0 percent. At high test temperature: 2.0 percent. Insulation resistance: Terminal to terminal: See table III. Terminal to case (case not a terminal): 10,000 megohms.

31、 Barometric pressure: Method 105 of MIL-STD-202. Test condition: .82 inches of mercury (80,000 ft). Vibration, low frequency: Method 204 of MIL-STD-202, condition B. Thermal shock: Method 107 of MIL-STD-202, condition A, except the high temperature shall be +125C for capacitors rated at 200, 400, an

32、d 600 volts dc. Immersion: Method 104 of MIL-STD-202, condition C. Insulation resistance: Terminal to terminal: Not less than 1/3 the value specified in table III. Terminal to case (case not a terminal): 5,000 megohms, minimum. Dielectric withstanding voltage: Insulating sleeve: 4,000 volts minimum.

33、 Terminal to terminal: 150 percent of rated dc voltage. Terminal to case (case not a terminal): 200 percent of rated dc voltage. Capacitance change: Not to exceed 10 percent of initial value. Dissipation factor: Not to exceed 110 percent of initial requirement. Provided by IHSNot for ResaleNo reprod

34、uction or networking permitted without license from IHS-,-,-MIL-C-18312/2D 6 Solderability: Method 208 of MIL-STD-202. Terminal strength: Method 211 of MIL-STD-202, conditions A and D. Condition A: Applied force 4 1/2 pounds. Condition D: 3 twists of 360 degrees. Low temperature and capacitance chan

35、ge with temperature: Conditions: 48 hours with rated voltage applied. Capacitance change: See table III. Life: Qualification: Test voltage 140 percent of rated voltage, 1,000 hours at high ambient temperature. Conformance: 250 hours at conditions specified for 1,000-hour test. Dissipation factor: At

36、 high ambient test temperature (any time 24 to 48 hours from start of test): Not greater than 2.0 percent. At high ambient test temperature (any time during last 48 hours of test): Not greater than 2.5 percent. At +25C (after life test): Not greater than 1.25 percent. Capacitance: At +25C (after lif

37、e test): Within 10 percent of initial value. Insulation resistance: At +25C (after life test). Terminal to terminal: Not less than 1/3 of value specified in table III. Terminal to case (case not a terminal): Not less than 5,000 megohms. Supersession information: See table I. TABLE III. Characteristi

38、c. Operating temperature range -55 to +125C -55 to +85C DC voltage rating (volts) 200 400, 600 50 High ambient test temperature +125C +125C +85C Low ambient test temperature -55C -55 C -55C Megohms x microfarads: At +25C 2,000 min 2,000 min 25,000 min At high ambient test temperature 10 min 40 min 5

39、00 min Insulation resistance (megohms): At +25C 1/ 12,000 12,000 50,000 At high ambient test temperature 1/ 150 600 5,000 Capacitance change at low temperature -15% max -15% max -8% max Life test voltage (% rated voltage) 140 % 140 % 140 % 1/ Need not exceed. Provided by IHSNot for ResaleNo reproduc

40、tion or networking permitted without license from IHS-,-,-MIL-C-18312/2D 7 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liab

41、ility whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-C-183

42、12, this document references MIL-STD-202. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5910-2013-002) DLA - CC Review activities: Army - AR Navy - AS, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-