DLA MIL-C-23486 B-1989 COLLAR COAT MAN-S POLYESTER WOOL GABARDINE BLUE《男式蓝色华达呢涤纶 羊毛领》.pdf

1、MPL-C-2348bB 83 9997706 0484I39.5 0 MIL-C-23486A(K) 14 May 1969 MILITARY SPECIFICATION This specification is -roved for use issues are those cited in the solicitation. U.S. Postal Service Manual (Application for qiec should be addressed to the Superintendent of Docu- mente, U.C. Gwermnt Printing Off

2、ice, Washington D.C. 20402.) Department of Defense (DoD) Standard CBlor Card of Official Standardize Shades for Sewing Threads 1968 (Application for copies should be address to the Calor Association of the United States, 200 Madicon Avenue, New York, NY 10016.) . 2.2 n-Goverrment WAications. %e foll

3、owing docunent(s) form a part of this domnent to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the WSS cited in the solicitation. Unless other specified, the issues of documents not listed in the DODIS

4、C are the issues of the hunents cited in the solicitation (see 6.2). UNIFORM CIASCIFICATION Ca3MITTEE Uniform Freight classification Mes (Application for copies should be addressed to the Uniform Classification Committee, FOm 1106, 222 South Riverside Plaza, Chicago, Illinois 60606.) NATI(X4A.L mR F

5、REIGHT TRAFFIC ASCOCIATION, INC., Ac;ENT National mtor Weight Classification (Pgplication for copies should be eddressed to American Trucking Associa- tion Inc., Tariff Order Section, 1616 P Street, N.W., Washington, D.C. 20026.) 2.3 Order of precedence. In the event of a conflict between the text o

6、f this omment and the references cited herein (exceDt for associated detail specifications, specification sheets, or MS standards), the text of this docu- ment shall take precedence. Wthing in this docunent, hbwever, shall super- sede applicable laws and regulations unless a specific exemption has b

7、een obtained. 3.1 Standard saples. Standard samples, when furnished, are solely for guidance and information to the Cuntractor (see 6.3). Variation hall not be tight or full lausing puckers, gathers, or ,lests. The interlining and !dges of the binding shall be Iecurely caught in the stitch- .ng. The

8、 interlining shall inish with the eyelet rein- :orcement pieces positioned on finish 1-3/4 + 1/8 inches wide. - 301 30 1 - SEAMI STCH TYPE - ;fa-1 each ide dge 1 sc- 1 each ide dge) Sf-1 f oldc nd 1 - STCH IN - 10-1 10-11 NDL - A A BOB/ LPR - A A l /. 10 Provided by IHSNot for ResaleNo reproduction

9、or networking permitted without license from IHS-,-,-MIL-C - 2 3 4 8 6B ( MC ) TABLE I MANUFACTURING kUIREMENTS OPERATION sem b 1 e -o 1 1 a r i n te r 1 in i n ca . # (contd) the inside and the felt pad- ding positioned on the outside of the interlining. The col- lar eyelet cover shall be positione

10、d so that in the f iniched collar, the covers shall be centered over the eyelets. a. Position the eyelet rein- forcement at eacn end of the collar interlining. Bind each edge of the interlining, catching the reinforcements in the seams. b. Center the strip of felt padding on the outside of the colla

11、r interlining with the ends of the padding suffi- ciently long to fold over each end of the interlining. Seam the padding to the interlining from end to end. 1/8 inch from top and bottom edges, respec- tively, of the padding. c. Lap the raw edge of the collar eyelet covers 1/2 to 5/8 inch on the top

12、 inside edge of the collar interlin- ing. Seam the covers to the interlining 1/4 inch from the raw edge of the covers. Pipe outer ply of collar. Finished appearance. Th e piping shall extend the full length along both edges of the outer ply and shall be uni- formly stitched without twists, gathers,

13、puckers, or pleats. STCH TYPE 30 1 30 1 301 SEAM/ STCH TYPE Sa- 1 Sau-2 Sa-1 STCHI IN - 10-14 10-14 10-14 NDL A A A BOB 1 LPR 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-C-2 34 8 6B (MC ) TABLE I lfANUPACTRINC REQUIREMENTS a. Seam a 5/8-i

14、nch-wide stril of scarlet piping to the outer ply 1/8 inch from upper anc lower edges. OPERATION b. Turn back the piping ani outer ply at upper and lower edges, uniformly working thc folded edge of the piping l/8 inch beyond the edge of the outer ply. Topstitch the outer i91y uniformly 3/16 inSa-1 ;

15、Sa- 1 STCH/ IN 10-14 10-14 NDL A (si A (si 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-2348bB 83 m 779970b 0484088 9 m MIL-C-23486B (MC) TABLE I MANUFACTURING REQUIREMENTS OPERATION Assemble collar. (contd) e. Smoothly fold the ends of

16、the outer ply to the inside over the ends of the inter- lining and press smooth and flat with a heated pressing iron or pressing machine. f. Turn collar lining at the seam to the inside of the collar and press smooth and flat with a heated pressing iron or pressing machine. g. Make one eyelet throug

17、h all plies midway + 1/16 inch of inner edges of-piping and 1-1/2 + 1/8 inches from each finishgd end of collar. Make collar extension tab. Finished appearance. . The extension tab shall extend 3/4 to 7/8 inch beyond the folded edge at the left end of the collar. a. Turn the top and bottom edges and

18、 the end of the col- lar lining at the left end of the collar to the inside of the lining and baste the turned portion along the top, front, and bottom edges to the body of the lining forming the col 1 ar ex t ens i on t ab. b. Stitch the collar exten- sion tab 1/16 inch from the top, frontr and bot

19、tom edges and continue the stitching at the back of tab to top row, forming a 1-1/8 inch-wide box stitch. STCH TPE Eye - let Hand 301 SEAMI STCH TYPE sc-1 p an( Dttom We 1 Sf-1 front dge 1 Ca-1 back %le) STCH/ IN 20 Per eye- let (mini mum ) 10-14 NDL A (si A BOB/ LPR - A :I A 14 Provided by IHSNot f

20、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-2348b 83 m 999990b 0484089 O m - to - 9. 1 o. 11. MIL-C-23486B (MC) TABLE I MANUFACTURING REQUIREMENTS OPERATION Fell ends of outer ply to collar. Finished appearance, Th e upper and lower edges at each end of the ou

21、ter ply shall not be visible in the finished collar. a. Tack the ends of the outer ply to the eyelet reinforce- ments and eyelet covers with overcast stitching. Mark collar. a. Mark the lining side of each collar at the center back as specified in 3.3.9. - or - b. Collar interlining may be marked at

22、 center of inter- lining with indelible ink stamp so it is readily visible when lifting collar lining. Clean an press collar. Finished appearance. The collar shall be clean and well pressed. a. Pull all basting threads. Trim all ends of stitching, and remove all loose ends of thread from the collar.

23、 Remove all spots, stains and t ickets from the collar, with the exception of one ticket on the outer ply, without injury to the material. b. Press the entire collar smooth and flat with a heated pressing iron, or pressing machi ne. STCH TYPE Hand SEAM/ STCH TYPE STCH/ IN 2-3 NDL C silk) - BOB/ LPR

24、- 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-234bB 83 Y 999998b 0484090 7 W MIL-C-2348f33 (MC) 3.7 Collar measurements. aie allar designated for wear with each size coat shall conform to the width/leqth measurements sbw in Table II (se

25、e 6.2). Table II. Width/Length measurements - 1/ Coat sizes (Collar width = 1-3/4 ins) (S, R, s, XL) Collar length (inches) 2/ Qllar length (inches) 2/ (Collar width = 2 ins) 30 32 33 34 35 36 37 38 39 40 41 42 43 44 46 48 14-1/2 15 15-1 /4 15-1/2 15-3/4 16 16-1/4 16-1/2 .16-3/4 17 1 7-1 /4 17-1/2 1

26、7-3/4 18 1 8-1 /2 18-3/4 14-1/2 15 15-1/4 15-1/2 15-3/4 16 16-1 /4 16-1/2 16-3/4 17 17-1/4 17-1/2 17-3/4 18 1 8-1 /2 18-3/4 - 1/ Tolerance on finished length: - +1/4 inch. Tlerance finished width: - +1/8 - 2/ Collar length measurement chal1 te taken along the center fran end to end. ?he mllars shall

27、 conform to the quality of product estab- lished iy this specification. aie occurrence of defects shall rot exceed tbse established by the applicable acceptable levels. inch. 3.8 Workmanship. 4. QUALITY ACSURANCE PrnvISICNc 4.1 Responsibility for inspection. bless otherwise specified in the con- tra

28、ct ar pirchase order, the amtractor is responsible for the performance of ali inspection requirements as specified herein. stcept as otherwise speci- fi 1 Weight 3.3.5 504 1 5 losure Hook material Identification 3.3.8 - 1/ Finish 3.3.0 Std. brn-11 1 Or (To the near. est whole number ) Pass or Fail (

29、No evidence of delamina- tion ) (To the near est o. O01 inch-pund ) II Il II II II Il Ib the near- est 0.1 oz. b the near- est 1.0 lb. !tb the near- est 1. O lb. Pass or Fail l the near- est 0.1 oz. Pass or Fail Tackiness 3.3.8 4.6.1 1 Pass or Fail 28 Provided by IHSNot for ResaleNo reproduction or

30、networking permitted without license from IHS-,-,-MIL-C-234bB 83 M 9999906 8484303 3 M MI L-C -234 86B ( K ) - 1/ mis requirement shall tie accepted ai the basis of the umtractors Certi- ficate of Cmpliance. - 2/ Except that the material chal1 k subjected to three wet-q cleaning cycles. - 3) Except

31、that the aging pocess dizatim of format Cornlidation of related requirements (laminated cloth) Deletiun of ctiaracteristics hich are a Quality Qntrol Representatives (design, measurenent). Inclusion of requirements hich have been unitted (ply) Simpiificatim of footnotes Nomenclature correction (Text

32、ure to yarns/inch) 4.6.1 Test for tackiness. At rocm temperature (60“ to 80F) press a piece of tissue paper against the lacquered surface hr 30 seconds, using any pres- sure capable of being exerted assembled and closed as specified in the appendix thereto. 29 Provided by IHSNot for ResaleNo reprodu

33、ction or networking permitted without license from IHS-,-,-_ _ MIL-C-234866 83 9999906 0484304 3 MIL-C-23486B (IC ) 5.2.2 kvel B. Sventy-five (75) mllars of me size and width only, pack- aged as qxcifie in 5.1, shall be pcked in fiberboard shipping mtainer with liner mnforming to Type CF, class-dome

34、stic, variety Ad, grade 275 and lining 200, size No. 2A of MIL-B-17757: the fiberboard used in fabricating the container and liner shall be assanbed,ciosed, an reinforced as specified in the appendix thereto. ?he contents of each shipping amtainer shall be ccmpletely anrered ai top and bttan with 60

35、-pund minimum basis-weight kraft paper conforming to grade B of u1-P-268. Cbllars, packaged as specified in 5.1, shall be packed in a manner to insure carrier acceptance and cafe delivery at destination. m- tainerc shall be in acardance with Uniform Freight Classification Rules, U.S. Postal Service

36、Manual, or regulations of other carriers applicable to the mxie of tran Spor t at ion. 5.3 Palletization. Wen qxcified (see 6.2), milars, picked as specified in 5.2. shall be palletized QI a 4-way =try pallet in acmrdance with lmci type la of MIL-STD-147. Each wepared load shall be b3nded with pimar

37、y arid secondary straps in accordance with the qpendix of MIL-CTD-147. %e pallet shall be 4-way, I, Qass 1, Style 1, Size A, Vbod Group I, II, III, or IV of MIL-P-15011, or, I-way, “e IV, V, or VIII, Qass 1, Style A, Size 2, Wood Group I, II, III, or IV, Grade A of W-P-71. interlocking of loads shal

38、l be effected ky reversing the pattern of each course. If the oxitainer is of a size which does mt mnform to any of the ptterns specified in MIL5Tu-147, the pallet pattern used shall be apprwed by the mntractirg officer. in ddition to any special mrking required by the contract or purchase order, sh

39、ipping containers and plletize mit loads shall be mrked in acmrdance with MIL-SID-129. 5.2.3 Commercial. 5.4 Marking. (mis section contains information of a general explanatory nature that may 6.1 intended use. ?he adlar described herein is intended to be wrn on the be helpful, but is not mandatory)

40、. Coat, Mans; Gabardine; Blue; by male personnel of the U.S. Marine Corps. 6.2 Acq uicition requirements. Acquisition doclanents mist specify tk fbl- lowing : (a) Title, number, and date of the specification. (b) Size and width required (see 1.2). (c) Whether first article is required (see 3.2). (d)

41、 Selection of awlicable levels of packing (see 5.2). (e) When palletizatim is required. 6.3 Camiple and shade samples. For information regarding availability of sanples of collars and u the standard shades specified, ddress inquiry to - the- procuring activity issuing the invitation for -bidc. 30 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-