1、 IL-C-Y42LLB 9979906 1996842 901 H I INCH POUND I MIL-C-44211B 4 January 1995 SUPERSEDING AMENDMENT 1 5 October 1990 5 October 1989 MIL-C-44211A(GL) MILITARY SPECIFICATION COATS, MENS; SERGE, POLYESTER/WOOL, ARMY GREEN 489, FUSIBLE, AND POLYESTER AND WOOL, BLUE 450 (MDW) AND BLUE 150 (MDW), FUSIBLE
2、This specification is approved for use by all departments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers polyester/wool serge, 1.2 Classification. The coats shall be of the following types, polyester/wool tropical, and polyester/wool elastique coats. classes
3、, and sizes as specified (see 6.2). Type I - Polyester and Wool Serge, Army Green 489, Type II - Polyester and Wool Tropical, Blue Shade 450, Type III - Polyester and Wool Elastique, Blue Shade 150, 11.3 ounces 10 ounces 16 ounces Beneficial comments (recommendations, additions, deletions) and any p
4、ertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19145-5099, by the Standardization Document Improvement Proposal (DD Form 1426) appearin
5、g at the end of this document or by letter. AMSC N/A FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44211B Class 1 - General Officers Class 2 - Other Of
6、ficers and Warrant Officers Class 3 - Enlisted Men Schedule of sizes (chest) X-Short Short Reqular Lonq X-Lonq 34 35 36 37 38 39 40 41 42 43 32 33 34 35 36 37 38 39 40 41 42 43 44 46 48 50 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 46 48 50 52 33 34 35 36 37 38 39 40 41 42 43 44 46 48 50 36 37 38
7、39 40 41 42 43 44 46 48 1.3 Uniform. When coats specified in this specification and trousers specified in MIL-T-43957 are procured as a uniform, the coat and trousers shall be cut from the same roll of material, the shades shall match, and the uniform shall conform to the type and class as follows (
8、see 6.2 and 6.9): Coat Trousers Type I Class 6 Type II Class 2 Type III Class 2 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless
9、otherwise specified, the issues of this document shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without
10、license from IHS-,-,-SPECIFICATIONS FEDERAL A-A-14 9 2 A-A-5 O O 6 7 A-A-5 O 19 6 A-A-5 O 19 8 A-A-50 19 9 Tape, Gummed, Paper, Plain Cloth, Flannel, Wool, Undercollar Cloth Thread, Silk Thread, Gimp, Cotton, Buttonholr; Thread, Polyester Core, Cotton- or Tape, Textile, Cotton, General Purpose Cloth
11、, Twill or Plain Weave, Polyester and Polyester Blend Braid, Textile (Flat) Thread, Nylon Label: For Clothing, Equipage, and Boxes, Shipping, Fiberboard Polyester-Covered Tentage (General Use) A-A-52 O 7 1 A-A-5 2 1 O 6 A-A-55 187 V-T-295 DDD-L-20 PPP-B-636 MILITARY MIL-C-36 8 Cloth, Satin, Rayon an
12、d Cloth, Twill, Braid, Textile, Tubular Cloth, Serge, Wool, Wool and Nylon, Button, Insignia, Metal, Uniform and Cap Cloth, Elastique, Wool Braid, Textile and Lace, Vellum, Woven, Pads, Shoulder and Sleeve-Head Coat Fronts Cloth, Tropical: Wool, Polyester/Wool Cloth, Felt Fabric Composite, Loads, Un
13、it: Preparation of Rayon Polyester and Wool Textile (For Blue Dress Uniform) Undercollar Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For Cloth, Twill, Polyester Container, Shipping and Storage, Coat (Hanger Pack) Cloth, Fusibles MIL-B-3 7 1 MIL-
14、C-8 2 3 MIL-B-3461 MIL-C-3738 MIL-B-13466 MIL-P-15064 MIL-P-15065 MIL-C-21115 MIL-C-29137 MIL-L-35078 MIL-C-44121 MIL-C-44192 MIL-C-44296 STANDARDS FEDERAL FED-STD-751 FED-STD-191 Stitches, Seams, and Stitching Textile Test Methods 3 Provided by IHSNot for ResaleNo reproduction or networking permitt
15、ed without license from IHS-,-,-MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Wood Members for Containers and Pallets, MIL-STD- 14 9 O - Provisions for Evaluating Quality of Inspection by A
16、ttributes Quality of Coats, Mens, Dress (Unless otherwise indicated, copies of Federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The f
17、ollowing documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD-adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of the documents not listed
18、 in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philade
19、lphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a c
20、onflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS . 3.1 First article. When specified (see
21、 6.2), a sample shall be subjected to the first article inspection (see 6.3) in accordance with 4.3. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44211B 3.2 Basic material 3.2.1 Tvp e I coat. The basic material shall be 11.3 ounce polyeste
22、r and wool serge, Army Green 489 (matching the standard sample for Army Green 489 and basic cloth), conforming to type III, class 3 Of MIL-C-823. 3.2.2 Type II coat (MDW). The basic material shall be 10 ounce polyester and wool tropical cloth, Blue Shade 450, conforming to type III, class 3 of MIL-C
23、-21115. 3.2.3 Type III coat (MDW). The basic material shall be 16 ounce wool elastique, Blue Shade 150, conforming to type III of MIL-C-3738. 3.2.4 Lininq. The material for lining the fronts, sleeves, yoke, back vent, and facings for inside breast pocket and as an option for pocket flaps and lower p
24、ocket facings shall be rayon lining, 3.7 ounces per square yard, Army Green 45 for Type I coats and Blue Shade 192 for Type II and Type III coats, conforming to class 1 of MIL-C- 368. As an alternate, the lining may be a polyester twill cloth conforming to MIL-C-44121, Army Green 461 for Type I coat
25、s and Blue Shade 192 for Type II and Type III coats, to approximate shade of the basic fabric. 3.2.4.1 Bindinq. The binding for the coat shall be cut on the bias of the same material as the coat lining (see 3.2.4). The width of the bias binding shall be 5/8 to 7/8 inch. rolls. The binding may be pla
26、ced on 3.2.5 Fusible interlininqs 3.2.5.1 Small parts fusible interlininq. The lapels, front facing, pocket flaps, top sleeve, undersleeve, top collar, and shoulder loops, known as “small parts“ shall use a charcoal, nonwoven fusible interlining. It shall conform to either type V or VI, class 1, sty
27、les A or B; or type VIII, class 1, style A of MIL-C-44296. The material shall have a uniformly distributed powder dot, paste dot, spunfused, or sintered nylon polyamide fusible adhesive evenly applied to one side in accordance with good commercial practice; for two sided application (see Table II, o
28、peration 18.c.(4) use type IX, class 1, styles B or C of MIL-C-44296. Any given coat shall incorporate the same small parts fusible material. As an alternate, a black or charcoal, woven, lightweight fusible interlining for small parts, conforming to type I, class 1, style A of MIL-C-44296 may be use
29、d. 3.2.5.2 Fronts fusible interlininq. The fusible interlining for the coat and side body fronts shall be a black or charcoal napped woven twill material conforming to type II, class 1, style B of MIL-C- 44296. The material shall have a uniformly distributed, dot-type nylon polyamide fusible adhesiv
30、e evenly applied on one side in accordance with good commercial practice. Any given coat shall incorporate the same fronts fusible material. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44211B 3.2.5.3 Colorfastness. All dyed finished fusib
31、le interlining materials shall show colorfastness to drycleaning as specified in MIL-C-44296. When no standard sample is available, the finished fusible materials shall show “fair“ colorfastness to drycleaning. 3.2.5.4 Shrinkase. The interlining, after fusing to the basic cloth as specified in 3.2.5
32、.5, shall not exceed 1.5 percent differential shrinkage when tested as specified in 4.4.3.1. Additionally, the interlining, after fusing to the basic cloth as specified in 3.2.5.5, shall not exceed 2.0 percent shrinkage after drycleaning when tested as required in 4.4.3.1. All drycleaned materials s
33、hall not exhibit any sign of bubbling, puckering, or delamination. 3.2.5.5 Fusinq press operatinq procedures and conditions. A single layer of fusible interlining shall be fused to a single layer of basic material on a dry-electrically-heated, conveyor-type fusing press which has the capacity of con
34、trolling and retaining pressure, dwell time, and temperature for a minimum of 8 hours. Pair or sandwich fusing which can create differential shrinkage, stitching, and uneven bonding shall not be permitted. A steam-sourced fusing press shall not be allowed for initial fusing operations. For optimum r
35、esults, the fusible material manufacturers recommendations for fusing dwell time, pressure, and temperature based upon the fusing equipment used and basic material being fused shall be utilized. Under no circumstances shall the dry heat temperature of the fusing press exceed 315OF. order to fuse bot
36、h the small parts and fronts fusibles together. Basic preproduction and production maintenance procedures, including a fusing press information chart, shall be required to ensure proper fusing press performance relative to temperature control, evenness in pressure head or roller contact, dwell time,
37、 and cleanliness. Results of the production maintenance procedures shall be recorded on Figure 6. Common fusing press settings shall be established in 3.2.6 Twill cloth. The material for the inside breast pocket, lower hanging pockets, armholes, shoulder, and pocket stays shall be polyester and cott
38、on, or polyester and rayon matching the shade of the basic material or dyed black. It shall conform to class 1 of A-A-52106, except that the nonfibrous material content and colorfastness requirements for perspiration and crocking shall not apply 3.2.7 Undercollar material. The material for the under
39、collar shall be wool flannel cloth conforming to A-A-50067, except that the colorfastness requirements for perspiration and crocking shall not apply. The color shall be Army Green 48 for the type I coat, Blue Shade 450 for type II, and Blue Shade 150 for type III. 6 Provided by IHSNot for ResaleNo r
40、eproduction or networking permitted without license from IHS-,-,-MIL-C-44211B As an alternate for the type I coat, wool blend felt fabric composite, color Army Green 48, conforming to MIL-C-29137 may be used or 100 percent polyester needlepunched nonwoven material weighing between 8.0 - 10.0 oz,/sq.
41、 yd., with a thickness between 0.070 - 0.095 inch at 0.6 psi, and exhibiting a minimum cross machine direction stiffness of 0.050 load lb., (when tested in accordance with FED-STD-191, TM 5202) can be used, The shade shall be Army Green 48. 3.2.8 Floatincr chest piece. The floating chest piece for t
42、he coat shall conform to type XVIII of MIL-C-15065. 3.2.9 Labels. Each coat shall have a combination size- identification label, a size label, an instruction label, and a cardboard instruction folder. All labels, except for the instruction folder, shall conform to DDD-L-20, and shall show colorfastn
43、ess to dry cleaning. 3.2.9.1 Combination size and identification label. The combination label shall conform to type VI, class 1 and 2 combined. 3.2.9.2 Size label. The size label shall conform to type VI, class 2. 3.2.9.3 Instruction label. The instruction label shall conform to type VI, class 3. Th
44、e letters for the caption shall be not less than 3/16 inch in height, and all other lettering shall be not less than 1/8 inch in height. The contents of the label for type I coats shall be as follows: COAT, MENS, ARMY GREEN 1. Dry clean only, low moisture. 2. Remove wrinkles or gloss with a steam ir
45、on or with a hot iron using a damp press cloth. Press/Iron temperature with steam shall be 325OF 2 6OF or wool setting with steam. 3. Roll press sleeves and lapels. 4. Utility press only. The contents of the label for type II and III coats shall be as follows : COAT, MENS, BLUE (MDW) 1. Dry clean on
46、ly, low moisture. 2. Remove wrinkles or gloss with a steam iron or with a hot iron using a damp press cloth. Press/Iron temperature with steam shall be 325OF 2 6OF or wool setting with steam. 3. Roll press sleeves and lapels. 4. Utility press only. Provided by IHSNot for ResaleNo reproduction or net
47、working permitted without license from IHS-,-,-MIL-C-qq2LLB 99999Ob L99bAi.19 2bb MIL-C-44211B 3.2.9.4 Label/taq. Each item shall be individually bar-coded with a paper tag for personal clothing items. The paper tag shall be standard bleached sulfate having a basis weight of 100 pounds. The paper us
48、ed for the tags shall have a smooth finish to accept thermal transfer and direct printing. The tags shall have a hole and shall be attached to each item by a fastener, clearly legible and readable by a scanner. The bar coding element shall be a 13 digit national stock number (NSN). The bar code type
49、 shall be a medium to high code density and shall be located so that it is completely visible on the item when it is folded and/or packaged as specified and so that it causes no damage to the item. 3.2.9.5 Uniform size tickets. When coat and trousers are procured as a uniform, a size ticket made of suitable commercial cardboard and measuring not less than 2-1/8 by 1-1/4 inches shall be included with both the coat and trousers. tacking. infor
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1