DLA MIL-C-62 1 D-2008 CAPACITORS FIXED ELECTROLYTIC (DC ALUMINUM DRY ELECTROLYTE POLARIZED) STYLES CE10 AND CE11.pdf

1、AMSC N/A FSC5910 MIL-C-62/1D 18 December 2008 SUPERSEDING MIL-C-62/1C 6 February 2004 MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, ELECTROLYTIC (DC, ALUMINUM, DRY ELECTROLYTE, POLARIZED) STYLES CE10 AND CE11 This specification sheet is approved for use by all Departments and Agencies of the Depar

2、tment of Defense. The requirements for acquiring the capacitors described herein shall consist of this document and the latest issue of specification MIL-C-62. STYLES CE10 - uninsulated CE11 - insulated NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only.

3、 Inches mm .002 .05 .032 .81 .047 1.19 .093 2.36 .500 12.70 2.000 50.80 INCH POUND INACTIVE FOR NEW DESIGN AFTER 27 MARCH 1979 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-62/1D 2 TABLE I. Styles CE10 and CE11 capacitors. Case dimensions 2/

4、3/ A B Type designation 1/ Capacitance DC rated voltage DC leakage Maximum impedance at 120 +10, -5 Hz at -40C +0C, -3C Dissipation factor .031 (.79) .016 (.41) f Volts a Ohms Percent Inches Inches CE1-C560C 56 5 2.0 178 20 .688 (17.48) .375 (9.53) CE1-C750C 75 5 2.0 133 20 .812 (20.62) .375 (9.53)

5、CE1-C101C 100 5 2.0 100 20 .938 (23.83) .375 (9.53) CE1-C181C 180 5 2.0 55 20 1.250 (31.75) .375 (9.53) CE1-C271C 270 5 2.0 37 20 1.500 (38.10) .375 (9.53) CE1-C150D 15 10 2.0 600 20 .688 (17.48) .250 (6.35) CE1-C390D 39 10 2.0 230 20 .688 (17.48) .375 (9.53) CE1-C560D 56 10 2.1 160 20 .812 (20.62)

6、.375 (9.53) CE1-C101D 100 10 2.3 90 20 .938 (23.83) .375 (9.53) CE1-C151D 150 10 2.7 60 20 1.250 (31.75) .375 (9.53) CE1-C221D 220 10 3.2 41 20 1.500 (38.10) .375 (9.53) CE1-C100E 10 15 2.0 800 20 .688 (17.48) .250 (6.35) CE1-C270E 27 15 2.0 296 20 .688 (17.48) .375 (9.53) CE1-C560E 56 15 2.3 143 20

7、 .812 (20.62) .375 (9.53) CE1-C750E 75 15 2.9 107 20 .938 (23.83) .375 (9.53) CE1-C101E 100 15 3.3 80 20 1.250 (31.75) .375 (9.53) CE1-C151E 150 15 4.1 53 20 1.500 (38.10) .375 (9.53) CE1-C5R6F 5.6 25 2.3 1430 20 .688 (17.48) .250 (6.35) CE1-C150F 15 25 2.3 530 20 .688 (17.48) .375 (9.53) CE1-C200F

8、20 25 2.5 400 20 .812 (20.62) .375 (9.53) CE1-C390F 39 25 3.3 206 20 .938 (23.83) .375 (9.53) CE1-C560F 56 25 4.0 143 20 1.250 (31.75) .375 (9.53) CE1-C750F 75 25 4.8 107 20 1.500 (38.10) .375 (9.53) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted

9、without license from IHS-,-,-MIL-C-62/1D 3 TABLE I. Styles CE10 and CE11 capacitors - Continued. Case dimensions 2/ 3/ A B Type designation 1/ Capacitance DC rated voltage DC leakage Maximum impedance at 120 +10, -5 Hz at -40C +0C, -3C Dissipation factor .031 (.79) .016 (.41) f Volts a Ohms Percent

10、Inches Inches CE1-C1R0G 1 50 3.3 7000 20 .688 (17.48) .250 (6.35) CE1-C5R6G 5.6 50 3.3 1250 20 .688 (17.48) .375 (9.53) CE1-C100G 10 50 3.5 700 20 .812 (20.62) .375 (9.53) CE1-C150G 15 50 4.4 470 20 1.250 (31.75) .375 (9.53) CE1-C220G 22 50 5.0 320 20 1.250 (31.75) .375 (9.53) CE1-C330G 33 50 6.0 21

11、0 20 1.500 (38.10) .375 (9.53) CE1-C8R2H 8.2 100 8.0 850 15 .938 (23.83) .375 (9.53) CE1-C100H 10 100 8.0 700 15 1.250 (31.75) .375 (9.53) CE1-C180H 18 100 9.4 390 15 1.500 (38.10) .375 (9.53) CE1-C1R0J 1 150 10.0 7000 12 .938 (23.83) .375 (9.53) CE1-C2R2J 2.2 150 10.0 3200 12 .938 (23.83) .375 (9.5

12、3) CE1-C5R6J 5.6 150 10.0 1250 12 .938 (23.83) .375 (9.53) CE1-C8R2J 8.2 150 10.0 850 12 1.250 (31.75) .375 (9.53) CE1-C100J 10 150 10.6 700 12 1.500 (38.10) .375 (9.53) 1/ Complete type designation shall include an additional digit to complete style. 2/ The dimensions shown are for style CE10; for

13、style CE11, add .062 (1.57) .062 (1.57) to the nominal dimension. 3/ Metric equivalents are given for general information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-62/1D 4 REQUIREMENTS: Dimensions and configuration: See figure 1 and

14、 table I. Case type: Tubular, uninsulated (CE10) and insulated (CE11). Capacitance value: See table I. Capacitance tolerance: -10, +75 percent. Operating temperature range: -40C to +85C. Solderability: Method 208 of MIL-STD-202. DC leakage: See table I. Capacitance: Method 305 of MIL-STD-202. Dissip

15、ation factor: See table I. Terminal strength: Method 211 of MIL-STD-202, test conditions A and D. Shock, medium impact: Method 205 of MIL-STD-202, test condition C. Vibration, high frequency: Method 204 of MIL-STD-202, test condition B. Salt atmosphere (corrosion): Method 101 of MIL-STD-202, test co

16、ndition B. Temperature cycling and immersion: Temperature cycling: Method 102 of MIL-STD-202, test condition D. Immersion: Method 104 of MIL-STD-202, test condition C,. DWV - Insulating sleeves - Method 301 of MIL-STD-202. 4,000 volts dc applied. DCL - Not more than 150 percent of initial measuremen

17、t. Capacitance change - 5 percent. DF - See table I. Corrosion - Not more than 10 percent. Moisture resistance: Method 106 of MIL-STD-202. Insulation resistance (insulating sleeve) - Not less than 100 megohms. DWV - Insulating sleeves - Method 301 of MIL-STD-202. 4,000 volts dc applied. DCL - Not mo

18、re than 150 percent of initial requirement. Capacitance change - 5 percent. DF - See table I. Corrosion - Not more than 10 percent. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-62/1D 5 Stability at low and high temperature: In accordance wit

19、h MIL-C-62. Step 1 (at +25C): DCL - See table I. Capacitance - See table I. DF - See table I. Step 2 (at -40C): Impedance - See table I. Step 3 (at +25C): DCL - See table I. Capacitance - +5 percent of initial value. DF - See table I. Step 4 (at +85C): DCL - Not more than 10 times initial value, or

20、meet initial 25C requirement. Capacitance - 20 percent of initial value. DF - See table I. Step 5 (at +25C): DCL - See table I. Capacitance - 5 percent of initial value. DF - See table I. Surge voltage: In accordance with MIL-C-62. DCL - See table I. Capacitance change - 6 percent. DF - See table I.

21、 Vent: Not applicable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-62/1D 6 Life: Method 108 of MIL-STD-202, test condition F. DCL - See table I. Capacitance change: 100 volts, dc rated, and less: -20, +15 percent. DC rated voltage above 100

22、 volts: 15 percent. DF - Meet the initial requirement or not exceed 150 percent of the initial measurement. Barometric pressure: Method 105 of MIL-STD-202. Shelf life: In accordance with MIL-C-62. Build factor: Not more than 4.0. Shelf factor: Not more than 3.0. DCL: Not more than 150 percent of ini

23、tial value. Capacitance change: 6 percent. DF: Not more than 175 percent of initial requirement. VERIFICATION: Qualification inspection: Not applicable. Retention of qualification: Not applicable. Conformance inspection: Group A inspection only. Provided by IHSNot for ResaleNo reproduction or networ

24、king permitted without license from IHS-,-,-MIL-C-62/1D 7 TABLE II. Supersession data. Superseded insulated part number Superseded uninsulated part number Recommended replacement style CE10 or CE11 001 063 CE1-C560C 002 064 CE1-C750C 003 065 CE1-C101C 004 066 CE1-C181C 005 067 CE1-C271C 006 068 CE1-

25、C150D 007 069 CE1-C390D 008 070 CE1-C560D 009 071 CE1-C101D 010 072 CE1-C151D 011 073 CE1-C221D 012 074 CE1-C100E 013 075 CE1-C270E014 076 CE1-C560E015 077 CE1-C750E016 078 CE1-C101E 017 079 CE1-C151E018 080 CE1-C5R6F 019 081 CE1-C150F 020 082 CE1-C200F 021 083 CE1-C390F 022 084 CE1-C560F 023 085 CE

26、1-C750F 024 086 CE1-C010G 025 087 CE1-C5R6G 026 088 CE1-C100G 027 089 CE1-C150G 028 090 CE1-C220G 029 091 CE1-C330G 030 092 CE1-C8R2H 031 093 CE1-C100H 032 094 CE1-C180H 033 095 CE1-C1R0J 034 096 CE1-C2R2J035 097 CE1-C5R6J036 098 CE1-C8R2J037 099 CE1-C100J Provided by IHSNot for ResaleNo reproductio

27、n or networking permitted without license from IHS-,-,-MIL-C-62/1D 8 Application data: All capacitors shall withstand an rms ripple current at 120 Hz and 85C as determined from the formula: CkrIWhere: Ir= rms ripple current in milliamps. C = nominal capacitance in microfarads. k = 20 for units rated

28、 at 5 to 250 volts dc inclusive. = 30 for units rated at 300 to 450 volts dc inclusive. Supersession data: See table II. NOTES: Reference documents. In addition to MIL-C-62, this specification sheet references the following documents. MIL-STD-202 (Copies of these documents are available online at ht

29、tp:/assist.daps.dla.mil/quicksearch or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previ

30、ous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 DLA - CC Review activities: (Project 5910-2008-031) Army - AT, AV, CR4, MI Navy - AS, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document a

31、s of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-