DLA MIL-C-82243 F-1993 COVERALLS RADIOACTIVE CONTAMINANTS PROTECTIVE《放射性污染警卫队工作服》.pdf

1、MIL-C-Z243F m 9999906 31852128 T44 m -POUND/ MIL-C-82243F 8 April 1993 SUPERSEDING MIL-C-82243E 19 June 1989 MILITARY SPECIFICATION COVERALLS, RADIOACTIVE CONTAMINANTS PROTECTIVE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope.

2、This specification covers the requirements f8 r one type of one-piece radioactive contaminant protective coverall made of polyester and cotton twill cloth. 1.2 Classification. The coveralls shall be in the following sizes (see 6.2): O Small - Medium - (Up to 43) Large - X-Large - (44 to 48) Benefici

3、al comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the St

4、andardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. a Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

5、om IHS-,-,-MIL-C-82243F W 9979906 L852L29 980 MIL-C-82243F 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specifie

6、d, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-5 2 O 9 4 JJ-S-746 JJ-W-155 NN-P-71 DDD-L-20 MILITARY MIL-P-15011 MI

7、L-G-16491 * MIL-B-17757 MIL-F-21840 MIL-C-21851 STANDARDS FEDERAL FED-STD-751 - Thread, Cotton - Stockinet, Surgical - Webbing, Textile (Cotton, Elastic) - Pallet, Material Handling, Wood, Stringer Construction, 2 Way and 4 Way (Partial) Tentage (General Use) - Label: for Clothing, Equipage and - Pa

8、llet, Material Handling, Wood, Post Construction, 4 Way Entry - Grommet, Metallic - Boxes, Shipping, Fiberboard (Modular Sizes) - Fastener Tapes, Hook and Loop, Synthetic - Cloth, Twill, Polyester and Cotton - Stitches, Seams, and Stitchings 2 Provided by IHSNot for ResaleNo reproduction or networki

9、ng permitted without license from IHS-,-,-MIL-C-82243F m 9999906 3852330 bT2 MIL-C-82243F MILITARY MIL-STD-105 - Sampling Procedures and Tables for MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STS-2073-1 - Department of Defense Materials Inspection by Attrib

10、utes Procedures for Development and Application of Packaging Requirements MIL-STD-2073-2 - Packaging Requirement Codes * (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robb

11、ins * Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawinqs, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the so

12、licitation. U.S. Postal Manual (Copies of the manual may be obtained from the Superintendent of Documents, U. S. Government Printing Off ice , Washington , DC 20402-0001.) 2.2 Non-Government Publications. The following document(s) form a part of.this document to the extent specified herein. Unless o

13、therwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL

14、 MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404.) Provided by IHSNot for ResaleNo reproduction or networki

15、ng permitted without license from IHS-,-,-UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808.) (Non-Government standards and ot

16、her publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the refer

17、ences cited herein, the text of this document takes precedence. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Guide samples. Samples, when furnished, are solely for guidance and information to the con

18、tractor (see 6.2). Variations from this specification may appear in the sample, in which case this specification shall govern. be subjected to first article inspection, in accordance with 4.3. 3.2 First article. When specified, (see 6.2), a sample shall 3.3 Material. It is encouraged that recycled m

19、aterials be used when practical as long as the materials meet the requirements of this specification. 3.3.1 Basic material. The basic material shall be a polyester and cotton twill cloth, shade yellow 3511 conforming to MIL-C-21851, standard sample piece number 84058. * 3.3.2 Thread, cotton. The cot

20、ton thread used for seaming and stitching shall be ticket nos. 30 and 50, 3 ply, Type I of A-A-52094. The color of the thread shall be an approximate match to the base fabric. * 3.3.3 Webbinq, elastic. The webbing shall be cotton, elastic, unbleached or bleached white conforming to the types and cla

21、sses of JJ-W-155 as follows or a woven or braided elastic webbing of equivalent grade as applicable may be used: TYPe I Class 10 I 7 II 1 Width Use 1-1/2 inch Back waist take-up - 1 inch Foot stirrups 5/16 inch Hem at leg bottom 4 Provided by IHSNot for ResaleNo reproduction or networking permitted

22、without license from IHS-,-,-MIL-C-82243F W 7999906 1852132 475 W MIL-C-82243F 3.3.4 Wristlets, knitted, cotton. The knitted cotton wristlets shall be bleached or unbleached, 3 inches wide, conforming to type I of JJ-S-746. O 3.3.5 Braid, nylon. The drawcord for the top of the coveralls shall be bra

23、ided of multifilament nylon, and shall conform to the requirements specified in Table I when tested as specified in 4.4.1. The finished braid shall be not less than 3/16 inch in width and the color shall be white. Table I - Phvsical characteristics Characteristic Requirements Yarn denier 840 denier

24、Number of carrier 16 Picks per inch 11 (min.) Ends per carrier 3 3.3.6 Grommets and washers. The grommets and washers shall conform to type I, class 2, size 1-J of MIL-G-16491. 3.3.7 Fastener tapes. The hook and loop fastener tapes shall conform to type II, class 1 of MIL-F-21840. White 3054 tape fa

25、steners shall be used in “small-medium“ size coveralls and Red 3852 tape fasteners in “large-X-large“ size coveralls to provide ready size identification. Tapes shall be as follows: Use - Width Tape 5/8 inch 1 inch 2 inch Hook Loop Loop Pocket flap Pocket Center back 3.3.8 Labels. 3.3.8.1 Combinatio

26、n label. Each coverall shall have a combination identification and instruction label conforming to type VI, class 15 of DDD-L-20. The printing shall show colorfastness to laundering. The inscription shall be as follows: COVERALLS, RADIOACTIVE CONTAMINANTS, PROTECTIVE FIBER CONTENT: 65% POLYESTER AND

27、 35% COTTON CONTRACT NO.: DIA-100-00-0-0000 (Example) NAME OF CONTRACTOR: NAME OF MANUFACTURER: (If other than contractor) LAUNDER IN ACCORDANCE WITH PRESCRIBED REQUIREMENTS 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-82243F m 9999906 185

28、2133 301 m MIL-C-82243F 3.3.8.2 Size label. The size label shall conform to type VI, O class 2 of DDD-L-20 and shall read as follows: SIZE: Small-Medium, up to size 43 (Example) STOCK NO.: 8415-00-000-0000 (Example) 3.3.9 Radiation Symbol. The marking for the radiation symbol shall be in accordance

29、with type IV of DDD-L-20. The radiation symbol shall be 3-3/4 inches in diameter conforming to the design and dimensions as shown in Figure 2. 3.4 Desiqn. The coveralls, as shown in Figure 1, shall be one piece having full length sleeves with knitted wristlets, a two- section left breast pocket with

30、 abutted flaps, and a channeled nylon drawcord at neck closure. webbing for back waist take-up, for drawing in around leg bottoms, and foot stirrup straps. A black radiation symbol shall be stamped on upper left back of coverall. It shall incorporate elastic 3.4.1 Fiqures. The figures are furnished

31、for information purposes only. When inconsistencies exist between the written specification and the figures, the written specification shall govern. 3.5 Patterns. Standard patterns to be used to cut working patterns will be furnished by the Government (see 6.3). The working patterns shall be identic

32、al to the Government patterns. Neither the Government patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns. The patterns provide a seam allowance of 1/2 inch for all regular double lapped, doub

33、le stitched seams. 3.5.1 Pattern parts. The component parts of the coveralls shall be cut from material as specified and in accordance with the following pattern parts: Materia 1 Nomenclature of pattern parts Cut parts I Cloth, polyester/ Front - Back 2 cotton twill Front 2 L/ Back 2 1;/ Sleeve, fro

34、nt 2 Sleeve, back 2 film badge) 1 Pocket flap (dosimeter) 1 Pocket, double (dosimeter and 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-82243F = 9999906 l1852L34 248 a . e a MIL-C-82243F i/ If the width of the material does not allow for ec

35、onomical cutting, the size Large - X-Large patterns, which provide for a four piece body, may be used. 3.5.2 Shade and size markinq. The component parts of the coveralls shall be marked, ticketed, or bundled to insure a uniform shade and size throughout the garment. Any method may be used except: 1.

36、 Corrosive metal devices. 2. Sew-on shade tickets. 3. Adhesive type tickets which discolor or adhere upon removal of ticket. NOTE: The use of ink pad numbering machine, rubber stamp or pencil is allowed, provided the numbering does not show on the outside of the garment and wherever possible, is cov

37、ered by the seam allowance. 3.6 Stitches, seams and stitchnqs. The stitches, seams, and stitching types specified in Table II shall conform to FED-STD-751. Wherever two or more methods for seam or stitch type are given for the same operation, any one may be used. Where stitch type 401 is used, the l

38、ooper (under thread) shall be on the inside of the coveralls. Ends of all seams produced by stitch type specified, all double needle seaming shall be 1/4 inch gauge with the row of stitching shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats or open seams will result.

39、All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. Hook and loop fastener tape stitching shall be 1/16 to 1/8 inch from the edge of the tape. When 2 inch wide fastener tape is used, an extra row of stitching shall be down the mid

40、dle of the length. The bight of the overedge stitching shall be 3/16 inch. The guide and knife shall be set to trim only the ravelled ends of the fabric. 3.6.1 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table II. 3.6.2 Thread breaks and ends of se

41、ams. Ends of seams and stitchings when not caught in other seams or stitchings shall be backtacked not less than 3/8 inch. The ends of the label stitching shall be overlapped not less than 3 stitches. Thread breaks (all stitch types) shall be secured by stitching back of the break not less than 1/2

42、inch. Skipped stitches or 401 stitch type thread breaks may be repaired by using 301 stitch type. When stitch type 401 is permitted as an option, it shall not be used unless the ends are caught in other seams or stitching. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted withou

43、t license from IHS-,-,-MIL-C-82243F W 9999906 1852135 184 W MIL-C-82243F * 3.7 Manufacturina operations reuuirements. shall be manufactured in accordance with operation requirements specified in Table II. The contractor is not required to follow the exact sequence of operations provided the finished

44、 coveralls is identical to that produced by following the sequence as listed in Table II. when using automatic equipment. alter the dimensional, serviceability or appearance requirements The coveralls Minor modifications are permitted where necessary These modifications shall not - cited in the spec

45、ification. O . O O 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IO. 1. 2. flIL-C-82243F 9999906 L852L3b 010 MIL-C-82243F TABLE II - CONSTRUCTION OF COVERALLS L/ OPERATION httinq i. The coverall shall be zut in strict accordance vith patterns fur

46、nished, vhich shall show size, ?lacement of components ?arts, directional lines or cutting, and notches or properly assembly of 111 parts. Directional lines shall be placed in the warp direction of the naterial and may vary from the warp direction DY not more than 1-1/2 inches. Measurements shall be

47、 taken at the top and bottom of the irectional line on patterns to the selvage edge of the fabric on the even side of the lay. The difference between the two measurements shall not exceed 1-1/2 inches. b. All component parts shall be cut from one piece of material. The filling flush side shall be th

48、e face and shall finish as the exposed surface of the coveralls. Replacement of defective components During the spreading, cutting and manufacturinc process, component parts having material defects or damages that are 9 ;TCH IYPE SEAM/ STCH TYPE ITCH N THREAD NDL BOB/ LPR Provided by IHSNot for Resa

49、leNo reproduction or networking permitted without license from IHS-,-,-flIL-C-822Y3F m 9999906 1852137 T57 m MIL-C-82243F NO. 3. 4. TABLE II- CONSTRUCTION OF COVERALLS (Continued) OPERATION classified as defects in section 4 shall be removed from production and replaced with non- defective and properly matched components. Markinq All parts shall be marked, bundled or ticketed to insure proper assembly