DLA MIL-DTL-10035 L-2001 TENT HEXAGONAL LIGHTWEIGHT M-1950《M-1950型轻量六边帐篷》.pdf

1、 MIL-DTL-10035L 01 January 2001 SUPERSEDING MIL-T-10035K 25 March 1988 DETAILED SPECIFICATION TENT, HEXAGONAL, LIGHTWEIGHT, M-1950 This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a pole-supported pyram

2、idal tent with a fire-resistant treated liner. A cover is provided to protect the tent and liner. 2. APPLICABLE DOCUMENTS * 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of th

3、is specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of the documents cited in sections 3 and 4 of this specification, whether o

4、r not they are listed in this section. 2.2 Government documents. Beneficial comments (recommendations, additions, deletions, clarifications) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directo

5、rate, Attn: DSCP-CNR, 700 Robbins Avenue, Bldg 6, Area D, Philadelphia, PA 19111-5096 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8340 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking

6、permitted without license from IHS-,-,-MIL-DTL-10035L 2 * 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in

7、the issue of the Department of Defense Index Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-55622 - Cord, Cotton, General and Special Purpose, Sash and Venetian Blind V-F-106 - Fasteners, Slide, Interlocking V-T-285 - Thr

8、ead, Polyester TT-P-595 - Preservative Coating, Canvas DDD-L-20 - Label: for Clothing, Equipage, and Tentage (General Use) GGG-N-202 - Needle, Sailmakers MILITARY MIL-F-495 - Finish, Chemical, Black, for Copper Alloys MIL-C-496 - Clip, End, Strap MIL-P-501 - Pins, Tent, Metal MIL-W-530 - Webbing, Te

9、xtile, Cotton, General Purpose, Natural or in Colors MIL-L-1709 - Lines, Tent MIL-DTL-1716 - Poles, Tent, Telescopic, Adjustable 5 Feet to 9 Feet, Magnesium MIL-S-1734 - Slips, Tent Line MIL-R-3390 - Rings, Dee MIL-C-3395 - Cloth, Netting, Nylon or Polyester MIL-C-10859 - Cloth, Oxford, Cotton (Perm

10、eable) MIL-F-10884 - Fasteners, Snap MIL-L-11075 - Loops, Strap Fastener MIL-C-12095 - Cloth, Wind-Resistant Sateen, Cotton; Fire and Water Resistant MIL-DTL-43002 - Shield, Stovepipe, Tent, Nonmetalic MIL-C-43256 - Cord, Polyester, Solid Braid MIL-T-43566 - Tape, Textile, Cotton or Polyester, Gener

11、al Purpose, Natural or in Colors MIL-C-43627 - Cloth, Duck, Cotton, Plied Yarns, Fire, Water, Weather and Mildew Resistant Treated, Lightdry Finish MIL-W-44049 - Webbing, Textile and Tape, Textile, Polypropylene, General Purpose, Natural or in Colors *(Unless otherwise indicated, copies of federal a

12、nd military specifications, standards, and handbooks are available from the Defense Automated Printing Service, Bldg 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) * 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings,

13、and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-10035L 3 DRAWINGS U.S. ARMY BIOLOGICAL A

14、ND CHEMICAL COMMAND 4-1-206 - Rings, Connecting, Round 5-4-221 - Tent, Hexagonal, Lightweight, M-1950; Illustration and List of Parts 5-4-222 - Assembly, View and Details 5-4-223 - Views and Details 5-4-224 - Front Details 5-4-225 - Assembled Front and Details 5-4-226 - Side 5-4-227 - Ventilator 5-4

15、-229 - Liner Assembly 5-4-230 - Liner Details 5-4-231 - Cover 5-4-580 - Repair Kit 5-4-1052 - Erection Instructions (Copies of drawings are available from the U. S. Army Biological and Chemical Command, ATTN: SSCNC-EMSS, NATICK, MA 01760-5057.) * 2.3 Non-Government Publications. The following docume

16、nts form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the i

17、ssues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A47 - Standard Specification for Ferritic Malleable Iron Castings A818 - Standard Specification for Coppered Carbon Steel Wire A853 - Standard Specification for Steel Wire, Carbon, for Gener

18、al Use B134 - Standard Specification for Brass Wire B159 - Standard Specification for Phosphor Bronze Wire B159M - Standard Specification for Phosphor Bronze Wire (Metric) B206 - Standard Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) Wire and Copper B206M - Standard Specification for Co

19、pper-Nickel-Zinc Alloy (Nickel Silver) Wire and Copper D6193 - Stitches, Seams and Sewing D2016 - Standard Test Method for Determination of Moisture Content Of Particulate Wood Fuels (Copies can be obtained from the American Society for Testing and Materials, 100 Barr Harbor drive, West Conshohocken

20、, PA 19428.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-10035L 4 NAVAL LOGISTICS LIBRARY (NLL) NASM 16491 NATIONAL AEROSPACE STANDARDS COMMITTEE (NA/NAS) NASM16491 - Grommet, Metallic, General Specification For (Copies may be obtained fr

21、om the Naval Logistics Library, 5450 Carlisle Pike, Mechanicsburg, PA. (717) 813-8387). AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI / ASQC Z1.4 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES (Applications for copies should be obtained from: American Society for Quality Control, 61

22、1 East Wisconsin Avenue, Milwaukee, WI 53202). * 2.4 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulat

23、ions unless a specific exemption has been obtained. 3. REQUIREM ENTS * 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 4.3). * 3.2 Materials and components. Materials and components shall be as specified herein and in referenced documents. Ma

24、terials not definitely specified shall be of the quality normally used by the manufacturer provided the complete item complies with all provisions of this document. It is encouraged that recycled materials be used when practical as long as it meets the requirements of this document. * 3.2.1 Cloth, w

25、ind- resistant sateen, cotton. The cloth for the tent shall be dyed Camouflage Green 483 and shall conform to MIL-C-12095. * 3.2.2 Cloth, cotton duck. The cloth for the peak reinforcement shall conform to MIL-C-43627 and the color shall be Camouflage Green 483. Requirements for colorfastness to weat

26、hering shall not apply for peak reinforcement. 3.2.3 Cloth, cotton, oxford. The cloth for the liner shall conform to type I, class 2 of MIL-C-10859. 3.2.4 Cloth, netting, nylon. The nylon netting for the ventilator opening shall conform to type I or II of MIL-C-3395. 3.2.5 Shield, stovepipe, tent. T

27、he flexible, silicone rubber coated stovepipe shield shall conform to MIL-DTL-43002. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-10035L 5 3.2.6 Tape textile, cotton. The tape shall be dyed Camouflage Green 483 and shall conform to type I,

28、 class 4, inch, inch, 1 inch and 2 inch width of MIL- T-43566. Alternatively, the tape shall be polypropylene conforming to type I, class 3 or 4, inch and 2 inch of MIL-W-44049 for covers and liners only. 3.2.7 Webbing, textile, cotton. The webbing shall be dyed Camouflage Green 483 and shall confor

29、m to type IIb, class 4, 1inch width and type III, class 4, 5/8 inch and 1-1/2 inch width of MIL-W-530. Alternatively, the webbing shall be polypropylene conforming to type IIb, 1 inch width, class 4 of MIL-W-44049 for covers. 3.2.8 Thread, polyester. 3.2.8.1 Tent and cover. The thread shall conform

30、to type I, class 1, sub-class B, Camouflage Green 483 of V-T-285. The dyed thread shall show fastness to weathering equal to or better than the standard shade sample. When no standard shade sample is available, the dyed thread shall show good fastness to weathering. 3.2.8.2 Liner. The thread shall b

31、e color natural and shall conform to type I or II, Class 1 of V-T-285. 3.2.8.3 Sizes. Thread sizes shall be as follows: For all stitching on tent - Size F for needle except zig-zag stitching, and bobbin bartacking and stitching indicated by “Z” on drawings For zig-zag stitching and - Size E for need

32、le bartacking and bobbin For stitching on tent - Size F for needle, indicated by “Z” on drawings size E for looper For all stitching on liner, - Size E for needle except stitching indicated and bobbin by “Z” on drawings For stitching on liner - Size E for needle, indicated by “Z” on size B for loope

33、r drawings Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-10035L 6 For stitching on cover indi- - Size FF for needle, cated by “Z” on drawing size F for looper 3.2.9 Lines, tent. The tent lines shall conform to class D or class G of MIL-L-17

34、09 in the types specified on the applicable drawings. 3.2.10 Stiffener, cord. The cord for the drip cap stiffener shall conform to type I, class 3, size No. 7 of T-C-571. 3.2.11 Toggle loops. The cord for the toggle loops shall conform to polyester, 1/8 inch diameter, Camouflage Green 483 of MIL-C-

35、43256. 3.2.12 Toggles, wood. The wood toggles shall be of the design and dimensions shown on Drawing 5-4-225. The wood for the toggles shall be straight-grained, sound and smooth lumber, kiln dried to not more than 15 percent moisture content when tested as specified in 4.3.1.1. The toggles shall be

36、 free from knots, shakes, checks, splits, or splintery surface. Any of the following woods may be used: Hickory Beech Pecan Maple, hard Red or White Oak Birch Rock Elm Ash 3.2.13 Toggles, metal. The metal toggles shall be of the design and dimensions shown on Drawing 5-4-223 and shall be fabricated

37、from copper alloy wire conforming to alloy number 270, half hard temper in accordance with ASTM-B134, 159, 159M, 206 and 206M. The toggles shall be given a black chemical finish conforming to MIL-F-495. 3.2.14 Slip, tent line. The tent line slips shall conform to type II of MIL-S-1734. 3.2.15 Fasten

38、ers, slide, interlocking. The slide fasteners shall conform to type III, style I, size H, wire stirrup pulls of V-F-106. Slide fastener chain shall be fabricated of brass or polyester coil. The slider for the brass chain shall be brass and the slider for the polyester coil shall be die cast zinc all

39、oy. The slide fastener tape shall be dyed to match Camouflage Green 483 and be water repellent and mildew-resistant. (Tapes made of 100 percent polyester need not be tested for mildew resistance.) The color of the tape after treatment will be considered acceptable. The tape shall show good fastness

40、to weathering. Alternatively, the slide fastener chain shall be polyester continuous monofilament in a ladder or coil type configuration. Color of the chain shall be Camouflage Green 483 or natural finish brass and the sliders shall be brass. 3.2.16 Ring dee. The dee ring shall conform to class 1 or

41、 2, configuration K, size 1 inch by inch of MIL-R-3390. * 3.2.17 Ring, connecting. The connecting rings shall be of steel wire or cast malleable iron, black enamel, phosphate treated, zinc plate finished, size 2 or 5 in accordance with Drawing 4-1-206. Provided by IHSNot for ResaleNo reproduction or

42、 networking permitted without license from IHS-,-,-MIL-DTL-10035L 7 * 3.2.17.1 Steel wire. The steel wire shall conform to steel numbers 1006 to 1020 in accordance with ASTM A853, ASTM A818, ASTM A641 or ASTM A809. * 3.2.17.2 Steel tube. The steel tube shall be seamless, round in accordance with AST

43、M A513 and ASTM A519. * 3.2.17.3 Malleable iron. The malleable iron shall be grade I (35018) Black, ungalvanized or grade II (32510)- Black, ungalvanized in accordance with ASTM A47. The first three digits of the grade designations indicate the minimum yield strength ( x 100 p.s.i.). The last two di

44、gits indicate the minimum elongation (percent in 2 inches). 3.2.18 Grommet, metallic. The Nos. 3 and 5 grommets shall conform to type III, class 3 and No.2 grommets shall conform to type II, class 3 of NASM 16491. 3.2.19 Fasteners, snap. The snap fasteners shall conform to style 2, finish 2, button

45、24 line size, size 1 and eyelet size 1 of MIL-F-10884. 3.2.20 Clip, end. The end clips shall conform to type I, class 1 or 2, size 1 inch of MIL-C-496. 3.2.21 Loops, strap fastener. The strap fastener loops shall conform to type III, style B of MIL-L-11075. 3.2.22 Snaphook. The snaphooks shall confo

46、rm to MIL-S-43770/10 or equal. 3.2.23 Pins, tent, metal. When required (see 6.2), the tent pins shall be type I, conforming to MIL-P-501. 3.2.24 Pole, tent, telescope. When required (see 6.2), the magnesium, adjustable telescopic tent poles shall conform to MIL-P-1716. 3.2.25 Kit, repair. The repair

47、 kit bag shall be fabricated from the material specified in 3.2.1 and of the design and dimensions shown on Drawing 5-4-580. The snap fastener on the pocket shall be as specified in 3.2.19. The bag containing the repair kit components, shall be securely tied and placed in the repair kit pocket of ea

48、ch completed tent. 3.2.25.1 Components, repair. Components for each kit shall consist of the items listed in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-10035L 8 TABLE I. Repair kit components Item Quantity Specification or reference Cloth, wind-resistant yard full 3.2.1 sateen, cotton width Thread, polyester, type 1 spool (2-ounce) 3.2.8 I, class 1, sub-class B, size FF, shade S-1 Needle, sailmakers 3 GGG-N-202 Size 16 Pusher, needle 1 Drawing 5-4-580 and wood specified in 3.2.12 Sleeve