DLA MIL-DTL-13486 13 D-2010 CABLE SPECIAL PURPOSE ELECTRICAL LOW-TENSION HEAVY-DUTY MULTIPLE CONDUCTORS SHIELDED.pdf

1、AMSC N/A FSC 6145 INCH-POUND MIL-DTL-13486/13D 21 May 2010 SUPERSEDING MIL-DTL-13486/13C 4 August 2000 DETAIL SPECIFICATION SHEET CABLE, SPECIAL PURPOSE, ELECTRICAL: LOW-TENSION, HEAVY-DUTY, MULTIPLE CONDUCTORS, SHIELDED This specification is approved for use by all Departments and Agencies of the D

2、epartment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-13486. Inches mm .020 .508 .060 1.52 .080 2.032 .115 2.921 .135 3.429 .672 17.068 12 10 2 8 6 4 1 SHIELD (OUTER) TAPE OR CLOTH BRAID SHEATH (.060 MINIMUM) INSULATIO

3、N CONDUCTOR SEPARATOR .672.020 5 3 9 11 7 .135 DIAMETER MAXIMUM .080-.115 DIAMETER CLOTH BRAID (OPTIONAL) INSULATED CONDUCTORS 3,5,7,9 AND 11 ARE SHIELDED FIGURE 1. Dimensions and configuration. NOTE: Dimensions are in inches. Metric equivalents are given for information only. Provided by IHSNot for

4、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-13486/13D 2 Dimensions and configuration. See figure 1. Conductor size. All conductors shall be size 20. See “Construction requirements for conductors” as specified in MIL-DTL-13486. Longitudinal shifting. This requi

5、rement of MIL-DTL-13486 shall not apply. Shielding. All shielding shall be electrically connected. Shielding internal. Internal shielding shall consist of a closely and uniformly woven wire braid applied directly over the insulated conductors by means of a multiple carrier braider. Each carrier shal

6、l have no less than four strands of .005-inch diameter tinned copper wire. The shielding shall provide no less than 85% coverage. Shielding outer. Outer shielding (see figure 1) shall consist of a closely and uniformly woven wire braid woven by means of a multiple carrier braider. Each carrier shall

7、 have no less than eight strands of .0063-inch diameter tinned copper wire. The shielding shall provide no less than 85% coverage. Insulated conductors, identification. See table I. Part or Identifying Number (PIN): M13486/13-1 Former PIN: 7724579 TABLE I. Color code chart. Conductor number Base Str

8、ipe 1 Red None 2 Red Black 3 Red White 4 Red Green 5 Black None 6 Black White 7 Black Red 8 Black Green 9 White None 10 White Black 11 White Red 12 White Green Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous is

9、sue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and re

10、lationship to the last previous issue. Referenced document. This document references MIL-DTL-13486. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-13486/13D 3 CONCLUDING MATERIAL Custodians: Preparing activity: Navy - SH DLA - CC Air Force -

11、 85 DLA - CC Review activities: Air Force - 71, 84, 99 (Project 6145-2010-014) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-