DLA MIL-DTL-15370 18 C-2008 COUPLERS DIRECTIONAL (PIN PLUG-IN TERMINATION).pdf

1、 AMSC N/A FSC 5985 MIL-DTL-15370/18C 7 May 2008 SUPERSEDING MIL-DTL-15370/18B 18 June 2003 DETAIL SPECIFICATION SHEET COUPLERS, DIRECTIONAL, (PIN PLUG-IN TERMINATION) This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring

2、 the couplers described herein shall consist of this specification sheet and MIL-DTL-15370. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Pin numbers are shown for reference - need not appear on the part. 4. Insulator around pin 1 shall be a contrasting

3、 color. 5. Unless otherwise specified, tolerance is .016 (.41 mm). 6. Termination for P/N M15370/18-001 through M15370/18-003, M15370/18-008: Input - pin 1 Coupled output - pin 3 Output - pin 4 Ground - pins 2, 5, 7, and 8 Pin 6 is not used in the circuit. FIGURE 1. Dimensions and configuration for

4、part numbers M15370/18-001 through M15370/18-003, M15370/18-008, and M15370/18-009. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/18C 2Inches mm .005 0.13 .020 0.51 .032 0.81 .090 2.29 .0200 5.08 .325 8.26 .380 9.65 .780 19

5、.81 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Pin numbers are shown for reference - need not appear on the part. 4. Insulator around pin 1 shall be a contrasting color. 5. Unless otherwise specified, tolerance is .016 (0.41 mm). 6. Termination for P

6、/N M15370/18-004: Input - pin 1 Coupled output - pin 4 Output - pin 5 Ground - pins 2, 3, 5, 7, and 8. FIGURE 2. Dimensions and configuration for part number M15370/18-004. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/18C 3Inches mm

7、Inches mm .005 0.13 .13 3.3 .015 0.38 .15 3.8 .025 0.64 .190 4.83 .03 0.8 .400 10.20 .030 0.76 .42 10.7 .032 0.81 .73 18.5 .04 1.0 .800 20.3 .115 2.92 1.08 27.4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Marking to include appropriate labeling of inp

8、ut, output and coupled port, above those respective pins. 4. Pin numbers are shown for reference - need not appear on the part. 5. Termination for P/N M15370/18-005 through M15370/18-007: Input - pin 1 Coupled output - pin 4 Output - pin 3 Ground - pins 2 and 5 Pin 6 not used in circuit. FIGURE 3. D

9、imensions and configuration for part numbers M15370/18-005 through M15370/18-007. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/18C 4Inches mm Inches mm .005 0.13 .188 4.77 .020 0.51 .200 5.08 .040 1.02 .400 10.83 .155 3.94 .500 12.70

10、 .180 4.57 .780 19.81 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Marking to include appropriate labeling of input, output and coupled port, above those respective pins. 4. Pin numbers are shown for reference - need not appear on the part. 5. Unless o

11、therwise specified, tolerance is .020. 6. Termination for P/N M15370/18-010 and M15370/18-013: Input - pin 5 Output - pin 4 Ground - pin 3 Coupled output - pin 2 Internal standoff - pin 1. FIGURE 4. Dimensions and configuration for part numbers M15370/18-010 through M15370/18-013. Provided by IHSNot

12、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/18C 5Inches mm Inches mm .005 0.13 .125 3.18 .020 0.51 .156 3.96 .032 0.81 .190 4.83 .040 1.02 .250 6.35 .520 13.21 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only.

13、3. Marking to include appropriate labeling of input, output and coupled port, above those respective pins. 4. Pin numbers are shown for reference - need not appear on the part. 5. Unless otherwise specified, tolerance is .010 (0.25 mm). 6. Termination for P/N M15370/18-011 and M15370/18-012: Input -

14、 pin 1 Output - pin 2 Coupled output - pin 3 Ground - pin 4. FIGURE 5. Dimensions and configuration for part numbers M15370/18-011 through M15370/18-012. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical characteristics. Coupling (d

15、B) VSWR max RF input power to primary Dash number Frequency range Nominal Tolerance Coupling variation (dB) max Effective directivity (dB) min Insertion loss (dB) max Primary line Secondary line Over frequency range Avg MHz MHz Watts 001N S 0.2 - 250 19.5 0.5 0.5 30 0.2-2.0 MHz 25 2.0-125 20 125-250

16、 MHz 0.6 0.2-0.4 MHz 0.5 0.4-125 0.6 125-250 MHz 1.30:1 1.50:1 0.2 - 2.0 02 - 250 1.5 4.0 002N S 0.5 - 500 11.5 0.6 0.6 25 0.5-5.0 MHz 25 5-250 15 250-500 MHz 0.3 0.5-1.0 MHz 0.5 0.5-500 MHz 1.30:1 1.70:1 0.5 - 5.0 0.5 - 500 1.5 3.0 003N S 1 - 1000 11.0 0.5 0.5 30 1-10 MHz 20 10-500 20 500-1000 MHz

17、0.6 1-10 MHz 0.6 10-500 1.0 500-1000 MHz 1.50:1 1.50:1 1.0 - 10 1.0 - 1000 1.0 2.0 004N S 10 - 400 10.0 0.3 0.25 35 0.65 1.10:1 1.10:1 10 - 400 10.0 005N S 50 - 400 10.0 1.0 1.0 25 0.6 1.30:1 1.30:1 50 - 400 5.0 006N S 50 - 400 15.0 1.0 1.0 25 0.6 1.30:1 1.30:1 50 - 400 5.0 007N S 50 - 400 20.0 1.0

18、1.0 25 0.6 1.30:1 1.30:1 50 - 400 5.0 008N S 250 - 1000 10.0 1.0 1.0 30 250-400 MHz 20 400-800 15 800-1000 MHz 0.4 250-600 MHz 0.7 600-1000 MHz 1.80:1 1.80:1 250 - 1000 5.0 009N S 0.01 - 35 15.0 0.5 0.5 20 0.5 1.30:1 1.30:1 0.01 - 35 4.0 010N S 1 - 60 20.0 1.0 0.5 25 2-32 MHz 20 1-60 MHz 0.2 2-32 MH

19、z 0.3 1-60 MHz 1.50:1 1.50:1 1 - 60 2.0 011N S 200 - 280 20.0 1.0 1.0 25 0.5 1.30:1 1.30:1 200 - 280 1.0 012N S 10 - 400 20.0 1.0 0.5 25 20-200 MHz 20 10-400 MHz 0.35 20-200 MHz 0.55 10-400 MHz 1.40:1 1.40:1 10 - 400 2.0 013N S 30 - 500 10.0 1.0 0.25 30 30-300 MHz 25 300-500 MHz 0.3 30-300 MHz 0.6 3

20、00-500 MHz 1.30:1 1.30:1 30 - 500 5.0 6 MIL-DTL-15370/18C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Physical and environmental characteristics. 1/ Dash number Weight Temperature range (operating on top non-operating on the bottom) The

21、rmal shock method 107 Vibration high- frequency method 204 Shock (specified pulse) method 213 Seal method 112 Solderability method 208 Resistance to soldering heat method 210 Terminal strength method 211 001 5.0 g -55C to +100C -65C to +100C - D I - Yes B - 002 5.2 g -55C to +100C -65C to +100C - D

22、I A Yes B A (3 lbs) 003 5.2 g -55C to +100C -65C to +100C - D I A Yes B A (3 lbs) 004 6.0 g -54C to +100C -65C to +100C A D A A Yes B - 005 11.4 g -54C to +100C -65C to +125C - - H - Yes - - 006 11.4 g -54C to +100C -65C to +125C - - H - Yes - - 007 11.4 g -54C to +100C -65C to +125C - - H - Yes - -

23、 008 5.0 g -55C to +100C -65C to +100C - D I A Yes B - 009 5.0 g -55C to +100C -65C to +100C - D I A Yes B - 010 7.0 g -54C to +100C -65C to +125C - - H - Yes - - 011 7.0 g -54C to +100C -65C to +125C - - H - Yes - - 012 7.0 g -54C to +100C -65C to +125C - - H - Yes - - 013 7.0 g -54C to +100C -65C

24、to +125C - - H - Yes - - 1/ Letters denote test conditions of MIL-STD-202. 7 MIL-DTL-15370/18C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/18C 8 REQUIREMENTS: Design, construction and physical dimensions: See figures 1 through 5. El

25、ectrical: See table I. Physical and environmental characteristics: See table II. Weight: See table II. Marking: Part number shall be located as shown on figures 1 through 5. Part number: M15370/18- (and a dash number from table I). Referenced Documents: In addition to MIL-DTL-15370, this document re

26、ferences the following: MIL-STD-202 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 DLA - CC Review activities: (Project 5985-2008-034

27、) Navy - AS, CG, MC, OS, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-