DLA MIL-DTL-17813 2-2009 EXPANSION JOINTS PIPE METALLIC SINGLE BELLOWS CORRUGATED REINFORCED.pdf

1、MIL-DTL-17813/2 29 August 2009 DETAIL SPECIFICATION SHEET EXPANSION JOINTS, PIPE, METALLIC, SINGLE BELLOWS, CORRUGATED, REINFORCED This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall co

2、nsist of this specification sheet and MIL-DTL-17813. DN C-NPS inch (mm) Flange OD inch (mm) 1/ B (bolt circle diameter) inch (mm) 1/ 50 2 (50.8) 6 (152.4) 4.75 (120.7) 65 2.5 (76.2) 7 (177.8) 5.5 (139.7) 80 3 (76.2) 7.5 (190.5) 6 (152.4) 90 3.5 (101.6) 8.5 (215.9) 7 (177.8) 100 4 (101.6) 9 (228.6) 7

3、.5 (190.5) 125 5 (127) 10 (254.0) 8.5 (215.9) 150 6 (152.4) 11 (279.4) 9.5 (241.3) 200 8 (203.2) 13.5 (342.9) 11.75 (298.5) 250 10 (254) 16 (406.4) 14.25 (362.0) 300 12 (304.8) 19 ( 482.6) 17 (431.8) 350 14 (355.6) 21 (533.4) 18.75 (476.3) 400 16 (406.4) 23.5 (596.9) 21.25 (539.8) 450 18 (457.2) 25

4、(635) 22.75 (577.9) 500 20 (508) 27.5 (698.5) 25 (635) 550 22 (558.8) - - 600 24 (609.6) 32 (812.8) 29.5 (749.3) 1/ See ASME B16.5, flange dimensions,150 pound. FIGURE 1. Expansion joint, single bellows, reinforced. AMSC N/A FSC 4730LENGTH LENGTH EQUALIZING RINGS FLANGE OD PIPE DIAMETER (C) B INCH-P

5、OUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17813/2 2 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. The illustration is for identification purposes only and is not intended to restrict desi

6、gns and shapes of fastening devices, which conform to the requirements and are within the envelope dimensions. FIGURE 1. Expansion joint, single bellows, reinforced Continued. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Construction: Corrugated bellows, reinfor

7、ced expansion joints shall be formed by one of the methods described in the EJMA Standards. They shall be provided with reinforcing or equalizing rings. Reinforcing rings, which support the root of the corrugation under internal pressure, are solid or tubular in cross section. Equalizing rings, whic

8、h support the root and sidewalls of the corrugation under internal pressure are usually “T” shaped in cross section. Equalizing rings, sometimes called control rings, have diameters larger than the outside diameter of the corrugation and limit the maximum compression of each corrugation. The classif

9、ication of the expansion joints covered under this specification sheet are as follows: Type II - shall be provided with reinforcing rings or equalizing rings. Class 1 - shall have a single bellows. Type II joints designed for the absorption of axial movement shall, when required, be provided with su

10、itable tie-rods, guide sleeves, or covers to prevent distortion of the expansion joint by weight of the reinforcement hardware. Materials and finishes. Materials and finishes for the bellows and flanges shall be in accordance with MIL-DTL-17813. Provided by IHSNot for ResaleNo reproduction or networ

11、king permitted without license from IHS-,-,-MIL-DTL-17813/2 3 The Part or Identifying Number (PIN) consists of the letters M, the basic specification number, specification sheet number, size, type, class, pressure rating, and end connection. PIN example: M17813/2-3-II-1-W Referenced documents. In ad

12、dition to MIL-DTL-17813, this document references the following: ASME B16.5 EJMA Standards CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - SH Air Force - 99 (Project 4730-2009-100) DLA - CC Review activities: Army - CE Navy MC, SA Air Force - 71 NOTE: The activities lis

13、ted above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Specification number Size Class M 17813 /2 - 3 - II - 1 - W M prefix Specification sheet number End connection (F for flanged ends, W for welded ends, and V for Vanstone ends.) Type Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-