DLA MIL-DTL-17813 5-2009 EXPANSION JOINTS PIPE METALLIC SINGLE BELLOWS FABRICATED.pdf

1、MIL-DTL-17813/5 29 August 2009 DETAIL SPECIFICATION SHEET EXPANSION JOINTS, PIPE, METALLIC, SINGLE BELLOWS, FABRICATED This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of thi

2、s specification sheet and MIL-DTL-17813. DN C-NPS inch (mm) Flange OD inch (mm) 1/ B (bolt circle diameter) inch (mm) 1/ 50 2 (50.8) 6 (152.4) 4.75 (120.7) 65 2.5 (76.2) 7 (177.8) 5.5 (139.7) 80 3 (76.2) 7.5 (190.5) 6 (152.4) 90 3.5 (101.6) 8.5 (215.9) 7 (177.8) 100 4 (101.6) 9 (228.6) 7.5 (190.5) 1

3、25 5 (127) 10 (254.0) 8.5 (215.9) 150 6 (152.4) 11 (279.4) 9.5 (241.3) 200 8 (203.2) 13.5 (342.9) 11.75 (298.5) 250 10 (254) 16 (406.4) 14.25 (362.0) 300 12 (304.8) 19 ( 482.6) 17 (431.8) 350 14 (355.6) 21 (533.4) 18.75 (476.3) 400 16 (406.4) 23.5 (596.9) 21.25 (539.8) 450 18 (457.2) 25 (635) 22.75

4、(577.9) 500 20 (508) 27.5 (698.5) 25 (635) 550 22 (558.8) - - 600 24 (609.6) 32 (812.8) 29.5 (749.3) 1/ See ASME B16.5, flange dimensions,150 pound. FIGURE 1. Expansion joint, single bellows, fabricated. AMSC N/A FSC 4730B LENGTH FLANGE FABRICATED BELLOWS LENGTH WELD END (C) FLANGE OD (C) INCH-POUND

5、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17813/5 2 NOTES: 1. Dimensions are in inches. Metric equivalents are given for information only. 2. The illustration is for identification purposes only and is not intended to restrict designs

6、and shapes of fastening devices, which conform to the requirements and are within the envelope dimensions. FIGURE 1. Expansion joint, single bellows, fabricated Continued. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Construction: Fabricated bellows expansion jo

7、ints shall be constructed of single-formed diaphragms joined together with circumferential seams at the inner and outer perimeters of the diaphragms, or constructed of single formed corrugations joined together with circumferential seams of the inner perimeters of the corrugations. The classificatio

8、n of the expansion joints covered under this specification sheet are as follows: Type III - shall have fabricated bellows. Class 1 - shall have single bellows. Type III expansion joints shall have fabricated bellows of disk or diaphragm construction. Materials and finishes. Materials and finishes fo

9、r the bellows and flanges shall be in accordance with MIL-DTL-17813. The Part or Identifying Number (PIN) consists of the letters M, the basic specification number, specification sheet number, size, type, class, pressure rating, and end connection. PIN example: M17813/5-3-III-1-150-W Specification n

10、umber Size Class M 17813 /5 - 3 - III - 1 - 150 - W M prefix Specification sheet number End connection (F for flange ends, W for weld ends, and V for Vanstone ends) Type Pressure rating Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17813/5

11、3 Referenced documents. In addition to MIL-DTL-17813, this document references the following: ASME B16.5 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - SH Air Force - 99 (Project 4730-2009-103) DLA - CC Review activities: Army - CE Navy MC, SA Air Force - 71 NOTE: The

12、activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-