DLA MIL-DTL-27072 76 C-2012 CABLE SPECIAL PURPOSE ELECTRICAL MULTICONDUCTOR (1 SHIELDED PAIR AND 8 WIRES UNDER A DOUBLE SHIELD) M27072 76SACA.pdf

1、 AMSC N/A FSC 6145 INCH-POUND MIL-DTL-27072/76C 12 March 2012 SUPERSEDING MIL-DTL-27072/76B8 December 2000 DETAIL SPECIFICATION SHEET CABLE, SPECIAL PURPOSE, ELECTRICAL, MULTICONDUCTOR (1 SHIELDED PAIR AND 8 WIRES UNDER A DOUBLE SHIELD), M27072/76SACA* This specification is approved for use by all D

2、epartments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27072. REQUIREMENTS: NOTE: The complete Part or Identifying Number (PIN) requires a color code designator (see table I). FIGURE 1. C

3、able configuration. WHITE /ORANGE WHITE /BLACK WHITE WHITE /RED WHITE /BROWN WHITE /GRAY WHITE /VIOLET WHITE /BLUE WHITE /GREEN WHITE /YELLOW SHEATH POLYVINYL CHLORIDE SHIELD NO. 1 TINNED COPPER TAPE POLYESTER SHIELD NO. 2 TINNED COPPER JACKET SHIELD NO. 3 TINNED COPPER Provided by IHSNot for Resale

4、No reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27072/76C 2 Design and construction: See figure 1 Number of conductors: 10 Temperature rating: 105C Components: Basic wire: M16878/17BDB* (see table I) Conductor: Tinned copper Primary insulation: Polyvinyl chloride Colors:

5、 White White with black tracer White with brown tracer White with red tracer White with orange tracer White with yellow tracer White with green tracer White with blue tracer White with violet tracer White with gray tracer Jacket over insulation: Polyamide Color: Natural Filler: Not applicable Cablin

6、g: Core: Number of conductors: 2 (1 twisted pair) Pitch or lay: 1.50 inches nominal Shield Number 3: Material: Tinned copper Gauge: 36 AWG Braid angle: 20 to 40 degrees First layer: Number of conductors: 8 Pitch or lay: 3.0 inches nominal Shield Number 2: Material: Tinned copper Gauge: 36 AWG Braid

7、angle: 20 to 40 degrees Binder tape material: Polyester (over shield number 2) Shield Number 1: Material: Tinned copper Gauge: 36 AWG Braid angle: 20 to 40 degrees Jacket undershield: Not applicable Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL

8、-DTL-27072/76C 3 Sheath: Material: Polyvinyl chloride Wall thickness: .040 inch (1.0 mm) nominal Tensile strength: In accordance with MIL-DTL-27072 Ultimate elongation: In accordance with MIL-DTL-27072 Accelerated aging: In accordance with MIL-DTL-27072 Color: See MIL-DTL-27072 Finished cable: See t

9、able I Cold bend: Mandrel size in accordance with MIL-DTL-27072 Dielectric withstanding voltage: 2,000 V rms Conductor resistance: In accordance with basic wire specification TABLE I. Construction data. PIN 27072/76 Basic wire except color M16878/17BDB*1/,2/(reference) Finished cable diameter inch(m

10、m) 10% Wire size (AWG) Number of strands Strand size Nominal diameter inch(mm) SACA 26 7 34 .044(1.12) .297(7.54) 1/ Asterisks (*) shall be replaced by the appropriate color designator. 2/ Dimensions are in inches. Metric equivalents are given for information only. Changes from previous issue: Margi

11、nal notations are not used in this revision to identify changes with respect to the previous issues due to the extensiveness of the changes. Referenced document. This document references MIL-DTL-27072. CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - SH Air Force - 85 (P

12、roject 6145-2012-015) DLA CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of this information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-