DLA MIL-DTL-27434 16 A-2008 ADAPTER CONNECTOR COAXIAL RADIOFREQUENCY BETWEEN SERIES SERIES LC to SERIES LT TYPE UG-586 B U.pdf

1、MIL-DTL-27434/16A 22 May 2008 SUPERSEDING MIL-A-27434/16 28 September 1960 DETAIL SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIOFREQUENCY, BETWEEN SERIES, SERIES LC to SERIES LT TYPE UG-586 B/U This specification is approved for use by all Departments and Agencies of the Department of Defens

2、e The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27434. FIGURE 1. Type UG 586 B/U connector adapter. AMSC N/A FSC 5935 Inactive for new design after 19 February 1982 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networki

3、ng permitted without license from IHS-,-,-MIL-DTL-27434/16A 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 2. Series LT interface dimensions. ENGINEERING DATA: Impedance: 50 ohms, nominal. Frequency range: 0 to 1 GHz. Voltage rating: 4,000 V rms, m

4、aximum at sea level. 1,000 V rms, maximum at 70,000 feet. Temperature rating: -65 C to +165 C. REQUIREMENTS: Dimensions and configuration: See figure 1. Mating characteristics: Series LC socket contact interface in accordance with MIL-DTL-27434 and series LT socket contact interface as specified on

5、figure 2. Inches mm .001 .002 .004 .635 .789 .810 0.02 0.05 0.10 16.13 20.04 20.57 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27434/16A 3 Contact insertion and withdrawal force (Series LT only). After insertion and removal of a pin 0.200

6、 inch minimum in diameter to a depth of 0.187 inch, minimum. All contact members shall make contact, within 0.031 inch of their tip ends, with a pin 0.176 inch diameter inserted to a depth of 0.187 inch minimum. The contact shall then be tested as follows: 1. A pin 0.168 inch minimum in diameter ins

7、erted to a depth of 0.187 inch minimum shall not deflect the contact members. 2. When a pin 0.196 inch minimum in diameter is inserted to a depth of 0.187 inch minimum, all contact members shall make contact with the pin 0.031 inch maximum from their tip ends. The contact shall then pass through a c

8、ylindrical hole 0.230 inch maximum in diameter and 0.500 inch long when a pressure of not more than 2 pounds is applied. Dielectric withstanding voltage: Method 301 of MIL-STD-202, 10,000 V rms minimum at sea level. Corrosion: Applicable. Vibration: Applicable. Shock: Applicable. Part or Identifying

9、 Number (PIN): UG-586 B/U. Supersession: This document supersedes Navy drawing REB 49164. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DT

10、L-27434, this document references the following: MIL-STD-202 REB 10076 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-004) DLA - CC Review activities: Navy SH Air Force - 99 NOTE: The activities listed above were interested in this

11、document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-