DLA MIL-DTL-28731 32 C-2012 CONNECTORS ELECTRICAL INSERT (INSULATOR) FEMALE RECTANGULAR POLARIZED CENTER SCREW LOCK FOR 117 REMOVABLE TYPE CONTACTS.pdf

1、AMSC N/A FSC 5935 MIL-DTL-28731/32C 25 May 2012 SUPERSEDING MIL-C-28731/32B 4 June 1985 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, INSERT (INSULATOR), FEMALE RECTANGULAR, POLARIZED, CENTER SCREW LOCK, FOR 117 REMOVABLE TYPE CONTACTS This specification is approved for use by all Departments a

2、nd Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-28731. FIGURE 1. Connector, female rectangular. INCH - POUNDS Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

3、se from IHS-,-,-MIL-DTL-28731/32C 2 FIGURE 1. Connector, female rectangular Continued. Inches .005 .050 .07 .100 .120 .138 .155 .187 .195 .234 .375 .400 .468 .532 mm 0.13 1.27 1.8 2.54 3.05 3.51 3.94 4.75 4.95 5.94 9.52 10.16 11.89 13.51 Inches .625 .652 .700 .870 .940 1.140 1.800 1.980 2.280 2.592

4、2.950 2.975 3.372 . mm 15.88 16.56 17.78 22.10 23.88 28.96 45.72 50.29 57.91 65.84 74.93 75.56 85.65 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28731/32C 3 FIGURE 1. Connector, female rectangular Continued. Inches mm .005 0.13 .018 0.46

5、.040 1.02 .052 1.32 .080 2.03 .082 2.08 .240 6.10 .385 9.78 .625 15.88 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28731/32C 4 FIGURE 1. Connector, female, rectangular Continued. Inches mm .025 0.63 .03 0.8 .050 1.27 .055 1.40 .060 1.52 .

6、080 2.05 .140 3.56 .250 6.35 .265 6.73 .760 19.30 1.00 25.4 1.37 34.8 1.980 50.49 POLARIZING POSITION CHANGE Keying position on both polarizing sockets can be rotated to desired position by loosening spanner nut (counter- clockwise), resetting socket in one of six positions then retightening spanner

7、 nut (clockwise). NOTE: Overtightening of spanner nut can fracture connector. Spanner keying wrench shown below. POLARIZING KEY MATING CODE R (FEMALE) Position 1 2 3 4 5 6 P (MALE) Position 4 5 6 1 2 3 Configuration B Connector polarization guide (layout) Provided by IHSNot for ResaleNo reproduction

8、 or networking permitted without license from IHS-,-,-MIL-DTL-28731/32C 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Tolerances between any two contact centers shall be .004 (0.10 mm). 4. Flatness, squareness, and parallelism shall be within dimensio

9、nal tolerances. 5. Contact hole details shall be in accordance with configuration B. 6. Mating connector information: M28731/32-0001 mate with M28731/31-0003 and M28731/31-0005. M28731/32-0002 mate with M28731/31-0004 and M28731/31-0006. M28731/32-0003 and M28731/32-0005 mate with M28731/31-0001. M2

10、8731/32-0004 and M28731/32-0006 mate with M28731/31-0002. 7. Polarization information: Polarization sockets are provided for indexing to preclude intermixing of adjacent connectors. By using a standard type spanner wrench, polarization sockets can be rotated to desired position. For parts supplied d

11、irectly to the government, polarization will be in the 1-1 position. For other polarization positions, see connector polarization guide configuration A (see marking, note 13d). For direct government acquisition a tool is supplied in the unit package for polarization socket adjustment. 8. Contact and

12、 terminal designations: Contacts and terminals shall be designated on the insulator using letters in the location shown on figure 1. 9. Tolerance shall be .010 (0.25 mm) unless otherwise specified. 10. For direct government acquisition crimp contacts M28731/35-0001 (see table I) are furnished in a p

13、lastic bag in each unit package (see marking, note 13a). 11. For direct government acquisition wrappost contacts are M28731/36-0001 (see table I) and are factory installed in connector body (see marking, note 13a). 12. Marking: a. Connectors supplied directly to the government shall be marked with t

14、he military Part or Identifying Number (PIN) (see table I). Example: M28731/32-0001. b. Connectors supplied with contacts to government end users shall be marked with the military PIN (see table I). Example: M28731/31-0001. c. Connectors supplied without contacts to government end users shall be mar

15、ked as follows: Example: M28731/31E (screw type or socket type from table I). The user shall complete the remaining portion of the military PIN as shown in table I based upon contact type he assembles. Example: M28731/32E-0004. d. Polarization position marking is not required unless otherwise specif

16、ied. When required, polarization marking shall be in accordance with the connector polarization guide (see configuration B). The marking shall appear following the PIN. 13. Applicable contact insertion and removal tools: Insertion - MIL-I-81969/5-01 Removal - MIL-I-81969/4-02 14. Rectangular shields

17、: Shall conform to MIL-DTL-28731/19, PIN M28731/19-0007 through M28731/19-0010, M28731/19-0017, and M28731/19-0018 for type A and B hardware. 15. Recommended hardware (not furnish) for panel mounting: (Four) .112-40-UNC-2A (length to suit) bolts with No. 4 washer and mating nut. 16. Rectangular shie

18、ld for connector M28731/32-007 shall conform to MIL-DTL-28731. PIN: M28731/38-001 must be ordered separately. FIGURE 1. Connector, female rectangular Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28731/32C 6 REQUIREMENTS: Dimensi

19、ons and configuration: See figure 1. Mating and unmating forces (torque): 120 inch-ounces, maximum. Dielectric withstanding voltage: 1,000 volts rms (sea level). Mechanical shock (specified pulse): Applicable. Contact retention: 6 pounds. Contact separation force: 1 ounce, minimum. Contact current r

20、ating: 5 amperes, 22 AWG wire. PIN: See table I. TABLE I. PIN information. Military PIN Actuating hardware Polarizing socket position Contact type Left side Right side M28731/32-0001 M28731/32-0002 M28731/32-0003 M28731/32-0004 M28731/32-0005 M28731/32-0006 M28731/32-000 Jackscrew type G Jack socket

21、 type D Fixed socket type F Fixed screw type E Fixed socket type F Fixed screw type E Jack socket type H 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Crimp, MIL-DTL-28731/35 Crimp, MIL-DTL-28731/35 Crimp, MIL-DTL-28731/35 Crimp, MIL-DTL-28731/35 Wrappost, MIL-DTL-28731/36 Wrappost, MIL-DTL-28731/36 Crimp, MIL-DTL-28

22、731/35 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-28731, this document references the following: MIL-DTL-28731/19 MIL DTL-28731/35

23、 MIL-DTL-28731/36 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28731/32C 7 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA - CC Navy EC Air Force 85 (Project 5935-2012-068) DLA - CC Review activities: Army AR, AT, AV, CR4,

24、MI Navy AS, MC, OS Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-