1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, THREADED, HIGH SHOCK, HIGH DENSITY, SHIPBOARD, CRIMP CONTACTS, RECEPTACLE, WALL MOUNTING, CLASSES D, DS, P, T, TS, Z, AND ZS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirem
2、ents for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-28840. Inches mm Inches mm Inches mm Inches mm .010 0.25 .100 2.54 .188 4.78 .898 22.81 .016 0.41 .130 3.30 .878 22.30 2.062 52.37 FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 MIL-DTL-2
3、8840/10E 14 November 2013 SUPERSEDING MIL-DTL-28840/10D 23 October 2009 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28840/10E 2 Shell size designator (see note 1) N dia max O reference mounting hole R T.P. centerline to centerl
4、ine S T A (11) .750 (19.05) .812 (20.62) .750 (19.05) 1.043 (26.49) 1.003 (25.48) .130 (3.30) .115 (2.92) B (13) .875 (22.22) .937 (23.80) .843 (21.41) 1.158 (29.41) 1.118 (28.40) C (15) 1.062 (26.97) 1.124 (28.55) .968 (24.59) 1.278 (32.46) 1.238 (31.45) D (17) 1.125 (28.58) 1.187 (30.15) 1.015 (25
5、.78) 1.403 (35.64) 1.363 (34.62) E (19) 1.312 (33.32) 1.374 (34.90) 1.140 (28.96) 1.528 (38.81) 1.488 (37.80) F (23) 1.500 (38.10) 1.562 (39.67) 1.281 (32.54) 1.738 (44.15) 1.698 (43.13) G (25) 1.625 (41.28) 1.687 (42.85) 1.392 (35.36) 1.838 (46.69) 1.798 (45.67) .157 (3.99) .142 (3.61) H (29) 1.812
6、 (46.02) 1.937 (49.20) 1.568 (39.83) 2.158 (54.81) 2.118 (53.80) J (33) 2.000 (50.80) 2.124 (53.95) 1.734 (44.04) 2.348 (59.64) 2.308 (58.62) .183 (4.65) .168 (4.27) NOTES: 1. Shell sizes are provided within parentheses for information and are not a part of the designator. 2. Dimensions are in inche
7、s. 3. Metric equivalents are given for information only. 4. Dimensions apply after plating. 5. Designator of backshell size within each shell size. FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-
8、DTL-28840/10E 3 REQUIREMENTS: Dimensions and configuration: See figure 1. Insert arrangements: See the MIL-STD-1698 figure corresponding to the desired shell size. Shell polarization: 1 thru 6, key position. Marking: Mark Part or Identifying number (PIN) on the shell. Mating counterpart: Plug connec
9、tors specified in MIL-DTL-28840/16 through /19, /26, /28 and /29. Installation and removal tools: As specified in MIL-I-81969/33 and /34. A backshell shall be used to meet moisture and water pressure requirements. PIN example: M28840/10 A G 1 P 1 Specification sheet number Key position 1, 2, 3, 4, 5
10、, 6 position Contact designator Shell size Insert designator RESTRICTIONS: Classes D and DS are inactive for NAVSEA new design, unless approved by NAVSEA. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue w
11、ere made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relatio
12、nship to the last previous issue. Referenced documents. In addition to MIL-DTL-28840, this document references the following: MIL-DTL-28840/16 MIL-DTL-28840/17 MIL-DTL-28840/18 MIL-DTL-28840/19 MIL-DTL-28840/26 MIL-DTL-28840/28 MIL-DTL-28840/29 MIL-I-81969/33 MIL-I-81969/34 MIL-STD-1698 Classes Code
13、 letter D A DS B P F T L TS N Z S ZS R Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28840/10E 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - EC Air Force - 85 DLA - CC (Project 5935-2013-108) Review activit
14、ies: Army AV, MI Navy - OS, SH Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1