DLA MIL-DTL-29563A-2003 ANTENNA SYSTEM AIMS SHIPBOARD ELECTRONICALLY STEERED OE-120 UPX.pdf

1、 MIL-DTL-29563A INCH-POUND13 November 2003 SUPERSEDING MIL-A-29563 (AS) 24 February 1989 DETAIL SPECIFICATION ANTENNA SYSTEM, AIMS SHIPBOARD, ELECTRONICALLY STEERED OE-120/UPX This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. T

2、his specification covers the requirements for performance and technical design for a Central Identification, Friend or Foe (IFF) electronically steered OE-120/UPX AIMS Shipboard Antenna System. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and

3、4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all spec

4、ified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein.

5、Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.1). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-S-901 - Shock Tests, H.I. (High Im

6、pact); Shipboard Machinery, Equipment, and Systems, Requirements for. MIL-C-5541 - Chemical Conversion Coatings on Aluminum and Aluminum Alloys. MIL-A-8625 - Anodic Coatings for Aluminum and Aluminum Alloys. MIL-C-13777 - Cable, Special Purpose, Electrical, General Specification for. MIL-DTL-15090 -

7、 Enamel, Equipment Light Gray (Navy Formula No. 111) MIL-E-24762 - Enclosures for Electronic Equipment, Survivable, Naval Shipboard Use. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: (Defense

8、Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43216-5000), by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 5985 DISTRIBUTION STATEMENT A: Approved for public release; distribution

9、 is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-29563A 2 STANDARDS FEDERAL FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities. DEPARTMENT OF DEFE

10、NSE MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment (Type I - Environmental and Type II - Internally Excited). MIL-STD-461 - Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment. MIL-STD-810 - Environmental Engineering Considerations a

11、nd Laboratory Tests. MIL-STD-1472 - Human Engineering. (Applications for copies should be addressed to the Document Automation and Production Service, Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The followi

12、ng other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. Defense Supply Center, Columbus (DSCC) DRAWINGS 87060 - Circuit Breakers, Magnetic, Panel Seal, Shock Enh

13、anced, Trip-free, Series Trip, Single Pole (0.2 to 30 Amperes). 87061 - Circuit Breakers, Magnetic, Panel Seal, Shock Enhanced, Trip-free, Series Trip, Two Pole (0.2 to 30 Amperes). 87062 - Circuit Breakers, Magnetic, Panel Seal, Shock Enhanced, Trip-free, Series Trip, Three Pole (0.2 to 30 Amperes)

14、. (Application for copies should be addressed to Defense Supply Center, Columbus, P. O. Box 3990, Columbus, Ohio 43216-5000, documents are also available at the DSCC web site: http:/www.dscc.dla.mil/). NAVSEA PUBLICATION ST000-AA-IDX-010-PEETE - Portable Electric/Electronic Test Equipment Index. (Ap

15、plications for copies should be addressed to the Document Automation and Production Service, Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) NAWCAD ATP-8201658 - Acceptance Test Procedure, Antenna Horn. (Application for copies should be addressed to NAWCAD, (Code 4.5.9.1)

16、, Villa Road, Saint Inigoes, MD. 200684-0010). 2.3 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents, which are DoD adopted, are those listed in the issue of the DoDISS cited in

17、the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-29563A 3 AMERICAN NATIONAL STA

18、NDARDS INSTITUTE (ANSI)/AMERICAN SOCIETY FOR QUALITY CONTROL (ASQC) ANSI/ASQC A8402 - Quality Management and Quality Assurance - Vocabulary. INTERNATIONAL ORGANIZATION FOR STANDARDS (ISO) ISO 9000 - Quality Management Systems Fundamentals and Vocabulary (DoD adopted). (DoD activities may obtain copi

19、es of ISO 9000 and ANSI/ASQC A8402 from Document Automation and Production Service, Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094. Private sector and other government agencies may purchase copies from the American National Standards Institute (ANSI), 11 West 42nd Street,

20、New York, NY 10036-8002). INSTITUTE OF ELECTRICAL AND ELECTRONIC ENGINEERS (IEEE) IEEE/EIA 12207.0 - Software Life Cycle Processes. (Application for copies should be addressed to the Institute of Electrical and Electronic Engineers (IEEE), 445 Hoes Lane, P. O. Box 1331, Piscataway, New Jersey, Unite

21、d States, 08855-1331, http:/www.ieee.org/). THE INSTITUTE FOR INTERCONNECTION AND PACKAGING ELECTRONIC CIRCUITS (IPC, INC.) IPC 2221 - Generic Standard on Printed Design. J-STD-001 - Requirements for Soldered Electrical and Electronic Assemblies. (Application for copies should be addressed to the In

22、stitute for Interconnection and Packaging Electronic Circuits (IPC, Inc.) at 2215 Sanders Road, Suite 200 South, Northbrook, IL 60062, http:/www.ipc.org/). SOCIETY OF AUTOMOTIVE ENGINEERS, INC (SAE) SAE-AS-20708 - Synchros, General Specification for. (Applications for copies should be addressed to t

23、he Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096.) TELECOMMUNICATIONS INDUSTRY ASSOCIATION TIA-232 - Interface between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange. (Applications for copies should

24、be addressed to TELECOMMUNICATIONS INDUSTRY ASSOCIATION, Standards and Technology Department, 2500 Wilson Boulevard, Arlington, VA 22201, 1-800-854-7179, http:/www.tiaonline.org/standards/searchn_order.cfm) 2.4 Order of precedence. In the event of a conflict between the text of this document and the

25、 references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 2.5 Ozone Depleting Substances (ODS). Any Class I Ozone Depleting Substance required in any of the specif

26、ications, standards, or handbooks referenced in this document is hereby deleted as a requirement and substituted with a “suitable substance.“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-29563A 3. REQUIREMENTS 3.1 Design objectives. The IF

27、F shipboard antenna system defined by this specification is an electronically steered beam radiating antenna that also provides the required Interrogation Side Lobe Suppression (ISLS). The ISLS radiation can be omni-directional or can be the antiphase (difference pattern) of the beam pattern. The po

28、sition or direction of the radiated beam shall be controlled by a 10-bit digital command signal. Also, it shall be possible to slave the position of the beam to radar 1X synchro data signals. When using digital input signals, the total operating cycle for positioning the beam from any bearing direct

29、ly to any other bearing shall be less than 50 microseconds and the beam shall not be required to pass through intervening synchro data inputs at rotational speeds from 1 to 90 revolutions per minute. The vertical coverage of the directive beam and the omni-directional (or difference) patterns shall

30、be as nearly identical as practical. 3.1.1 Allowable design changes. The performance requirements and the technical design approaches required by this specification are achievable through known engineering techniques. Design approaches other than specified herein shall also provide equal or better p

31、erformance. Prior approval to use these other approaches is required. 3. us radar coperformi a system. Texpostemperatur3.OE-120/UP3.STD-313, and with specifito be instal3.smallewhe3.preferaoper3.3.more than oadjustments orProvided by IHSNot for ResaleNo reproduction or networking permitted without l

32、icense from IHS1.2 Shipboard configurations. Because this antenna will be installed on several types of ships having varionfigurations, versatility in the methods of installation of this antenna shall be provided. A capability for ng periodic repair and maintenance by ships personnel shall be includ

33、ed for all equipment of this antennhese installation and maintenance capabilities shall consider the normal environmental conditions of ure to impulses of stack gases, wind loading, ice loading, nuclear air blast, salt laden air and spray, and the e variations encountered throughout the world. 2 Gen

34、eral requirements. The general requirements (see 6.11) shall apply for the design and construction of the X except as hereinafter specified. 4 2.1 Prohibited materials. Equipment shall not contain toxic or hazardous substances in accordance with FED-http:/www.epa.gov/ebtpages/pollutants.html. The us

35、e of ozone depleting chemicals in accordance http:/www.epa.gov/ebtpages/pollutants.html shall require approval of the contracting activity. Unless otherwise ed, the materials specified in table I should not be used. Special care shall be taken when selecting materials led in a controlled atmosphere.

36、 TABLE I. Prohibited materials. Carcinogens Glass fibers (exposed) Lithium and lithium compounds, except batteries approved for the intended service conditions Magnesium or magnesium alloys Polyvinyl chloride (PVC) except when used for parts leads Radioactive commodities Zinc or zinc alloys 2.2 Sele

37、ction of parts. The selection of parts in accordance with (see 6.11) shall not preclude the use of parts of r physical characteristics, provided that the use of such parts shall be restricted to applications reby a saving in weight or one linear dimension of at least 25 percent can be affected. 2.3

38、Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally ble materials shall be used to the maximum extent possible provided that the material meets or exceeds the ational and maintenance requirements, and promotes economically advantageous life cycle cos

39、ts. 2.4 Parts management. Electrical and mechanical parts management (see 6.4). 2.5 Modular assemblies and subassemblies. Whenever modular assemblies and subassemblies are used in ne location, all like assemblies and subassemblies shall be interchangeable without requiring modifications. Adjustment

40、of normal functional controls will be permitted. -,-,-MIL-DTL-29563A 5 3.2.6 Solid state components. Maximum feasible use shall be made of solid state components. Use of thermionic and ionizing tubes, such as in the transmitter output stages, shall require prior approval. Solid state components capa

41、ble of working over a broad range of temperatures shall be used wherever technically feasible and cost effective. Microelectronic devices employed in the design of the antenna system requiring MIL-PRF-38535, appendix A, shall conform to (see 6.8). 3.2.7 Maintenance design. The equipment shall be des

42、igned to provide ease of maintenance. Extension cords, extender boards, and adapter cables shall be supplied with the equipment. 3.2.8 Self testing. Self testing techniques shall be employed to the greatest extent practicable. Means shall be provided for the localization of faults to reasonably smal

43、l circuit entities, which are easily replaceable. 3.2.9 Connections for standard test equipment. Connections shall be readily available for such external standard test equipment as may be required for operational check-out tests. 3.2.10 Test points and test features. Test points and test features sh

44、all be provided. Self-test features and ease of fault isolations shall be emphasized. 3.2.11 Captive screws and nuts. Captive screws and nuts shall be utilized, wherever feasible, to preclude loss of hardware when equipment is disassembled for maintenance. 3.2.12 Thermal design. Forced ventilation o

45、r equivalent technique to prevent hot spots and reduce internal temperature shall be provided where required. 3.2.13 Power. Nominal operating configuration shall be 115 volts, 60 Hz and 400 Hz. The input power connector contacts or pin assignments and conductor color code internal to the equipment s

46、hall be as specified in table ll. TABLE ll. Conductor designations. 1/ Conductor assignment Conductor designator Conductor color 115 V rms 115 V rms Safety ground A C B White Black Green 1/ Ship electrical distribution systems are delta-connected; this precludes the use of the safety ground as a pow

47、er-carrying conductor. Safety ground connections for bonding and grounding are provided for EMI and personnel safety considerations. 3.2.14 Overload protection. Protective devices shall be provided within the equipment for protection from damage due to overload and excessive heating. The circuit bre

48、aker protection for the equipment, and the interface to the electrical power system, shall be coordinated to ensure that the circuit breaker closest to the cause of an overcurrent or fault current condition will trip first. Multi-phase circuit breakers shall disconnect all phases when an overload oc

49、curs in any one phase. Protective devices shall not be installed in the neutral unless neutral power sensing is essential to protect operation of the equipment and the overcurrent protective device simultaneously opens all conductors of the circuit, and operates such that no pole can operate independently. When electrical overcurrent protection devices are used internally, the status (that is open or closed) shall be displayed on the operating panel and restoration of the device shall be control