DLA MIL-DTL-31010-1995 JACKET AIRCREW COLD WEATHER WITH REMOVABLE LINER AND HOOD《空勤人员寒冷天气用带可拆衬套和防护帽的夹克》.pdf

1、_ _ MIL-DTL-31010 I 999990b 2002540 20T MIL-DTL-31010 22 Mav 1995 DETAIL SPECIFICATION JACKET, AIRCREW, COLD WEATHER, WITH REMOVABLE LINER, AND HOOD This specification is approved for use by all departments and agencies of the Departinent of Defense. 1. SCOPE 1.1 Scope. This specification covers the

2、 requirements for a jacket with removable liner and hood. 1.2 Classification. The jacket and liner shall be provided in the following sizes and lengths: Sizes - X-small, Small, Medium, Large, Extra-Large Lenqths - Short, Regular, Long The hood shall come in one size only. NOTE: The lengtkis (Short,

3、Regular, and Long) may be abbreviated as S, R, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3LO10 9997906 200254L 146 MIL-DTL-31010 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are sp

4、ecified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned th

5、at they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 specif i documen Specifications, standards, and handbooks. The following cations, standards, and handbooks form a part of this t to

6、the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-5 O 18 6 A-A-50 195

7、 A-A-50 19 8 A-A-5 O 19 9 A-A-5 5 126 A-A-5 5 1 9 5 V-B-871 V-F- 1 O 6 KK-L-241 DDD-L-20 PPP-B-6 O1 PPP-B- 6 3 6 MILITARY MIL-B-371 - MIL-C-3735 - MIL-F-10884 - MIL-P-15011 - MIL-C-43303 - MIL-T-43709 - Cloth, Buckram, Woven and Nonwoven Thread, Aramid Threild, Gimp, Cotton, Buttonhole Thread, Polye

8、ster Core, Cotton- or Fastener Tape, Hook and Loop, Synthetic Thread: Para-Aramid, Spun, Intermediate Button, Sewing Hole, and Button, Staple, Fastener, Slide, Interlocking Leather, Cattlehide, Rigging Label: For Clothing, Equipage and Boxes, Wood, Cleated Plywood Boxes, Shipping, Fiberboard Polyest

9、er-Covered Modulus (Plastic) Tentage (General Use) Braid, Textile, Tubular Cuffs, Knit, Wrist and Ankle, and Cloth, Fasteners, Snap Pallets, Material Handling, Wood Post Cord, Elastic Cotton Tape, Textile, Aramid Knltted Construction, 4-Way Entry 2 Provided by IHSNot for ResaleNo reproduction or net

10、working permitted without license from IHS-,-,-flIL-DTL-31OLO 9999906 2002542 O2 MIL-DTL-31010 MIL-C-43774 -. Cloth, Plain or Pajama Check Weave, MIL-C-43824 - Cloth, Synthetic Fur, Knitted MIL-C-43842 - Cloth, Oxford, Aramid MIL-B-81813 - Batting, Aramid or Nonvoloid Fiber, MIL-C-83429 - Cloth, Pla

11、in and Basket Weave, Aramid Quilted Aramid STANDARDS FEDERAL FED-STD-595 - Colas Used Tn Government Procurement FED-STD-751 - Stitches, Seams and Stitching MILITARY MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads (Unless 0therwiL.s indicated, copies of the above sp

12、ecifications, standards, and handbooks are available from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) The following other Government documents, drawings, and publications form a part of -chis document to the extent specified herein. Unless

13、 otherwise specified, the issues are those cited in the solicitation. 2.2.2 Other Governrtent documents, drawinqs and publications. Federsl Acquisition Regulation (FAR 52.209) (Copies of the manual may be obtained from the Superintendent of Documents, US Government Printing Office, Washington, DC 20

14、40:-;001.) 2.3 Non-Government publications. The following documents form a part of this document; to the extent specified herein. otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified,

15、the issues of documents not listed in the LiODISS are the issues of the documents cited in the solicitation (see 6.2). Unless AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to the American Society for

16、 Testing Und Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-31010 = 9999906 2002543 T19 MIL-DTL-31010 AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI/ASQC 21.4 - Sampling Procedure

17、s and Tables for Inspection of Attributes (Applications for copies should be addressed to the American National Standards Institute, 11 West 42nd Street, New York, NY 10036-8002.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, t

18、he text of this document takes precedence. however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Nothing in this document 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection, in accordance w

19、ith 4.3. 3.2 Recycled, recovered, or environmentally preferable material. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically adv

20、antegeous life cycle costs. 3.2.1 Basic material. The basic material for the jacket and hood shall be a woodland camouflage printed 6.0 ounce aramid oxford cloth, conforning to the requirements of class 2 of MIL-C-43842. The material for the construction (bagging) of the inner portion of the lower f

21、ront pockets shall be woodland camouflage printed cloth conforming to class 2, ground shade cloth conforming to class 2, or Camouflage Green 483 matching color chip 34094 of FED-STD-595. The pocket material shall conform to class 1 of MIL-C-43842. 3.2.2 Lininq. 3.2.2.1 Jacket lin!:;ls. The material

22、for the jacket lining shall be plain weave aramid cloth conforming to type II, class 6 of MIL-C-83429. color chip 34094 of FED-STD-595. The color shall be Camouflage Green 483 matching 3.2.2.2 Liner and haod lininq. The material for the jacket liner and hood lining shall be aramid or quilted nonvolo

23、id fiber batting in accordance with YIL-B-81813. The color of the outercovering cloth shall be Camouflage Green 483, matching color chip 34094 of FED-STD-595 and the color of the needle thread shall be camouflage green. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

24、icense from IHS-,-,-MIL-DTL-3LOLO I 9999906 2002544 755 3. rib MIL MIL-DTL-31010 2.3 Knitted wrist cuffs. The wrist cuffs shall be a 1 X 1 ,-C-3735. The color shall be Camouflage Green 483 matching knit aramid conforming to type IV, class 2, size 2 of color chip 34094 of FED-STD-595. The cuffs shall

25、 be of a seamless construction and doubled to meet the finished measurements. The wrist cuffs shall finish 3-1/2 inches in length, and the opening shall finish 2-3/4 to 2-7/8 inches. 3.2.4 Slide fastener thonq and liner attachment loop. The aramid tape shall be 1/4 inch wide conforming to MIL-T-4370

26、9. The color shall be Camouflage Green 483 matching color chip 34094 of FED-STD-595. Ends of the thong shall be seared or dipped in a colorless, noncombustible resin (see 6.5). Each slide fastener shall be furnished wi:.h a thong of sufficient length to measure 2-1/2 to 3 inches (folded) when attach

27、ed to the slider pull tab. The thong shall be attached 7.0 the slider pull tab by threading one end of thong throilgh end of slide fastener pull tab and, with ends open, bartacking together with two vertical bartacks 1/2 to 3/8 inch apart, with the end of the top bartack 1/4 to 1/2 inch from the end

28、 of the slide fastener pull. On the inside inseam of the jacket sleeve, at the hem, there shall be a 1-3/8 to 1-1/2 strip bartacked along both cut edge edges. 3.2.5 Interlininq. The buckram for interlining the jacket collar, front facings, and hood brim shall be cotton buckram conforming to type I,

29、natural or bleached of A-A-50186. 3.2.6 Svnthetic fur. The synthetic fur for the hood fur ruff shall be natural whitrz, conforming to MIL-C-43824. The natural lay of the fur shall go upwards. 3.2.7 Bindinq. The material for the binding shall be aramid cloth conforming to MII,-C-43774. The color shal

30、l be Camouflage Green 483 matching color chip 34094 of FED-STD-595. 3.2.8 Slide fasteners. The slide fastener for the jacket front closure shall conform to type IV, style 8, size M, of V-F-106, with a short tab pull, 18-1/2 inch brass chain with a black chemical finish, 3/4 i;ech wide aramid tape, C

31、amouflage Green 483 matching color c3l.p 34994 of FED-STD-595 in color. The slide fastener for the sleeve utility pocket shail conform to type I, style ;, size M, short tab pull, brass chain with a black chemical finish, 3/4 inch wide aramid tape, Camouflage Green 483 matching color chip 34094 of FE

32、D-STD-595 in color and a 4-3/4 inch chain. 3.2.9 Hook and loop ape fasteners. The hook and loop tape fasteners shall be Camouflage Green 483 matching color chip 34094 of FED-STD-595 1 inch wide, conforming to type I or II, class 2 of A-A-55126. The requirements in Table I are for all sizes. The hook

33、 and loop tapes shall be cut with either a hot knife or ultrasonically. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-31010 = 9999906 2002545 891 MIL-DTL-31010 TABLE I. Fastener tape lenqth (Inches) Hook Loop 1 Jacket front closure 2 Pock

34、et or type V, class 1, of MIL-B-371. Ends of drawcords shall be impregnated or dipped with a cellulose acetate or cellulose butyrate to prevent fraying. This compound may be accepted on the basis of a contractors certificate of compliance. The hood pull-cord length shall be 50 2 1 inches long and th

35、e brim draw cords shall be 24 2 1 inches long. 3.2.12 Eyelets. The eyelets shall be corrosion resistant with a black chemical finish and an inside diameter of 7/32 inch. The eyelets for the waist drawcord and hood shall be reinforced with a 1 X 1 inch piece of outer fabric fused to the lining. 3.2.1

36、3 Thread. The thread shall be aramid,Camouflage Green 483, or matchifig color chip 34094 of FED-STD-595, 40 and 60 tex, 2-ply conforming to A-A-5019s or para-aramid, nominal tex 39, 2- ply thread conforming to A-A-55195. Cotton-covered polyester core thread conforming to ticket No. 50, 2-ply of A-A-

37、50199 may be used as an alternate thread for bartacking. The color shall be Camouflage Green 483 matching color chip 34094 of FED-STD-595. 3.2.14 Gimp. The ainp for reinforcing the buttonholes shall conform to type I or il, size No. 8 of A-A-50198. The color shall be Camouflage Green 483 matching co

38、lor chip 34094 of FED-STD-595. 3.2,15 Hood brim wire. The wire for the edge of the hood brim shall be bright, 0.080 + 0.003 inch diameter copper wire, dead soft, and shall not crack or break down when tested for material identification (a certificate of Compliance is acceptable), diameter (by a micr

39、ometer, take 3 determinations report average to nearest 0.001 inch), resistance to cracking or breaking (the wire shall be bent 360 degrees over a mandrel of the same diameter and then straightened. This bending and straightening shall be repeated once or more in the same place in the wire. Any crac

40、king or breaking observed in the wire shall be considered a test failure). The hood brim wire shall measure 36-1/2 2 1/4 inches. 3.2.16 Leather keepers. The leather keepers for the hood drawcords shali be made from leather conforming.to type II, class 2 of KK-L-241. The color of the leather shall be

41、 natural and the thickness shall be not less than 3/16 inch. Reference Figure 3 for dimensions. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-31010 3.2.17 Snap fasteners. The snap fasteners used for attaching the hood to the jacket shall

42、conform to style 2a, brass, finish 2, male and female complete, consisting of stud and eyelet size 1 or 2 and socket conforming t.n MIL-F-10884, except an uncapped button may be used to attaci: Lhe socket. Universal series 200, prong type, snap fastener or equal (see 6.6) may be used, except the mat

43、erial for the spring in the socket component shall conform to the requirements in MIL-F-10884 for spring temper. As an alternate, a 3.2.18 Labels. 3.2.18.1 Jacket and liner labels. Each jacket and liner shall have a combination identification-size label, classes 1 and 2, and an instruction label, cl

44、ass 3; or a combination size, identification and instruction label, class 14, conforming to type IV of DDD-L-20. The label color shall be Medium Green, Cable numbers 70043, 70130 or 70131. The instruction label for the 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. jacket shall contain the following information

45、: Wear as an outer garment. Wear button-in liner for added insulation. Adjust closures and drawcords to ventilate; avoid over Brush snow or frost from garments before entering heated For fast drying. remove liner from coat. Lubricate slide fasteners with wax. Machine washinq: Use permanent press cyc

46、le. Wash in warm water using a mild laundry detergent. Use a fabric softener in the rinse cycle to avoid static electricity. Hand washinq: Rinse in clean warm water. Field launder: in accordance with Formula XI of FM-10-280 or for Post Laundry, Fsrmula X. heating of body. shelters. Wash in warm wate

47、r using mild detergent. DO NOT USE STARCH OR BLEACH. Drying: Dry at medium heat. Use a fabric softener to reduce static electricity. To drip dry, remove from water and place on a rustproof hanger. The instruction label for the removable liner shall contain the following information: 1. 2. Dry remova

48、ble liner and jacket separately when damp or wet. Wash by hand or machine launder on permanent press cycle in warm water with a mild laundry detergent. Rinse thoroughly. fabric softener in either the wash or the dry cycle to reduce static electricity. for post laundry, Formula X. Drip dry or machine

49、 dry at medium heat. Use a 3. Field launder in accorzknce with Formula XI of FM-10-280 or 4. DO NOT USE STARCH OR BLEACH. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-DTL-3101O = 999990b 2002548 5T0 MIL-DTL-31010 3.2.18.1.1 Label placement. The jacket and the jacket liner size label shall be stitched on all four sides (through all plies on the liner, and through the lining fabric o