DLA MIL-DTL-32068-2000 LEATHER CATTLEHIDE STRAP VEGETABLE TANNED [Superseded DLA KK-L-271 H CANC NOTICE 2 DLA KK-L-271 H VALID NOTICE 1 DLA KK-L-271 H DLA KK-L-271 G (2) DLA KK-L-2.pdf

1、INCH-POUND MIL-DTL-32068 July 12, 2000 SUPERSEDING March 9, 1976 KK-L-27 1H MILITARY DETAILED SPECIFICATION LEATHER, CATTLEHIDE, STRAP, VEGETABLE TANNED This specification is approved for use by all Department and Agencies of the Department of Defense. 1. SCOPE This Military Detailed Specification c

2、overs the requirement for vegetable tanned cattlehide strap leather. 1.2. CLASSIFICATION. The leather will be in the following types: Type I - Sides Type II - Backs Type III - Bends Type IV - Double shoulders Class 1 - Mildew resistant treated Class 2 - Untreated Beneficial comments (recommendations

3、 additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-COC, bld 6-1-D, 700 Robbins Ave, Philadelphia, PA 191 11 -5096. AMSC NIA FSC 8330 Provided by IHSNot

4、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32068 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this spe

5、cification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they ar

6、e listed. 2.2 Government documents. MIL-L-8067 (Unless otherwise indicated, copies of Federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19 1 1 1-5094.) 2.2 Non-Government publicatio

7、ns. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not list

8、ed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS D- 5053 Resistance to Crocking of Leather D- 6075 Cracking Resistance of Leather D- 2209 Tensile Strength of Leather D- 3495 Hexane Extraction of Leather D- 2617 Total Ash

9、 in Leather D -6018 Determining of Lead Salts in Leather D- 1814 Measuring Thickness of Leather Units D -2813 Practice for sampling leather for physical and chemical tests (Applications for copies should be addressed to American Society For Testing and Materials, 100 Barr Harbor Drive, West Conshoho

10、cken, PA 19428.) ANSUASQC 21.4 (Applications for copies should be addressed to ANSUASQC American Society for Quality Control 61 1 East Winconsin Ave. , Milwaukee W1 53202) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the do

11、cuments. These documents also may be available in or through libraries or other informational services.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32068 2.3 Order of Precedence. In the event of a conflict between the text of this docu

12、ment and the references cited herein (except for related associated specifications or specification sheets), the text of this document takes precedence. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Mat

13、erials The strap leather shall be full grain or corrected grain cattlehide. Corrected grain leather shall be buffed or snuffed only to the extent necessary to remove superficial blemishes. 3.2 Tannage. The leather shall be vegetable tanned. 3.3 Physical requirements. 3.3.1 Trim (form and area). The

14、leather shall be furnished in the form of sides, backs, bends or double shoulders as required for the type specified. The area in terms of square feet shall be legibly marked in the butt area on the flesh side of the leather except that double shoulders shall be marked on the flesh side in the right

15、 hand corner formed by the straight edge cut and the belly cut. 3.3.2 Thickness. The thickness of the leather shall be as specified in the acquistion document (see 6.2). A tolerance of remove necessary amount of acetonitrile and inject Note: Samples may have to be diluted further to fall within stan

16、dard curve. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32068 4.4.3.5 Testing equipment: a. HPLC System with variable UV detector and integrating computer. Suitable syringe and glassware. b. A micro-Bondapak C18 column (Waters Associate

17、s P/N 2734) or equivalent. c. 0.45-micron polycarbonate filters (Nuclepore Corporation, Catalog No. 11 1107) or equivalent. d. Calculator capable of doing linear regression. e. Reagents: Acetonitrile (Chromatographic grade). 4.4.3.5.1 Typical mobile phase. Mix 550ml of distilled water and 450ml of a

18、cetonitrile. Filter and degas the solution. The concentration may be varied to meet system suitability requirements Within range 50% to 40 acetonitrile. 4.4.3.5.2 Typical chromatographic conditions: Injection Volume 20 Microliters Flow 2.5 dminute Detector 235 nm 4.4.3.6 System suitability. Inject t

19、he highest working standard until 2 percent agreement is reached between two successive injections. Chromatograph for approximately 15 minutes. Determine that, after the solvent front, one impurity peak elutes before the major peak. Elution for monoiodomethyl-para-tolylsulfone is about 6 minutes and

20、 for Diiodomethyl-para-tolylsulfone is about 8.5 minutes. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32068 4.4.3.7 Procedure. Inject each standard and sample preparation in duplicate allowing each injection to run for at least 15 minut

21、es. Measure the peak response for the Diiodomethyl-para- tolylsulfone. Note: The run time may have to be increased for samples with late eluting peaks. Perform a linear regression of peak response (area) versus concentration for each of the components. For each component: Concentration (ppm) in leat

22、her = Concentration (ppm) X75 from linear regression. Sample wt(g) 3.7 Cracking. The leather shall be tested for cracking in accordance with ASTM-D-6075. The diameters of the mandrels for the indicated thickness shall be as follows: Thickness of leather (ounces) Diametr of mandrel (inches) 2to5% 5%t

23、o9% 9 % and over 5. PACKAGING. 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to as

24、certain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department orDefense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Depa

25、rtments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. The strap leather covered by this document is intended primarily for use in post office mail bags, cases, belts, holsters, shoulder straps, and cap v

26、isors. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32068 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of this specification b. Type and class required (see 2.0) c. Thickne

27、ss required (see 3.3.2). d. Color and finish required (see 3.3.3) e. Colorfastness values when other than specified values are required (see 3.3.4) f. Packageing requirements (see 5.1) g. When fungicides are not required (see 3.5) 6.3 Lead chromate, lead pigments, or other lead salts should not be u

28、sed in the finish. 6.4 Subiect term (key word) listing. Sides Backs Bends Fungicide MILITARY INTERESTS: Custodians Army - GL Reviewer Activities ARMY - MD, AT, Air Force 11.6 CIVIL AGENCY COORDINATING ACTIVITY: DLA GSA - FSS PREPARING ACTIVITY: DLA - CT Project 8330-0201 11 Provided by IHSNot for Re

29、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32068 STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL INSTRUCTIONS l. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and 2. The submitter of this form must complete blocks

30、 4, 5, 6, and 7 and send to preparing activity. 3. The preparing activity must provide a reply within 30 days from receipt of the form. NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current contracts. Comments submitted on

31、 this form do not constitute or implv authorization to revision letter should be given. Leather, Cattlehide, Strap, Vegetable Tanned 4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.) 5. REASON FOR RECOMMENDATION c. ADDRESS (Incl

32、ude Zip Code) 700 Robbins Ave (Bldg 6, C&T) PHILADELPHIA, PA 19111-5092 I I DD Form 1426, FEB 1999 (EG) PREVIOUS WHS/DIOR. Feb 99 b. TELEPHONE (Include Area Code) (1) Commercial (2) DSN (21 5) 737- 8035 444-8035 IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT: Defense Standardization Program Office (DLSC-LM) 8725 John J. Kingman Road, Suite 2533 Fort Belvoir, Virginia 22060-6221 Telephone (703) 767-6888 DSN 427-6888 EDITION IS OBSOLETE 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-