DLA MIL-DTL-32173-2004 GLOVES FLYERS INTERMEDIATE COLD HAU-15 P《HAU-15 P中等冷飞行员手套》.pdf

1、INCH-POUND MIL-DTL-32173 20 August 2004 DETAILED SPECIFICATION GLOVES, FLYERS, INTERMEDIATE COLD, HAU-15/P 1. SCOPE 1.1 Scope. This document covers one type of intermediate cold flyers gloves, HAU-15/P. 1.2 Classification. The gloves will be of one type as follows. 1.3 Schedule of sizes The gloves w

2、ill be of the following sizes (see 6.2). SCHEDULE OF SIZES 5, 6, 7, 8, 9, 10 and 11 Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-COCT (Bldg 6), 700 Robbins Ave., Philadelphia, PA. 19111-

3、5092 or emailed to Leo.Baileydla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST online database at www.dodssp.daps.mil. AMSC N/A FSC 8415 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

4、from IHS-,-,-MIL-DTL-32173 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples

5、. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards

6、, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). FEDERAL SPECIFICATIONS V-T-295 - THREAD, NYLON COM

7、MERICAL ITEM DESCRIPTIONS A-A-50195 - THREAD, ARAMID A-A-50199 - THREAD, POLYESTER CORE, COTTON OR POLYESTER-COVERED DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-C-3735 - CUFFS, KNIT, WRIST general (applicable to all components unless otherwise indicated herein) Component misplaced, operation omitted, o

8、r operation not properly performed 118 Lining reversed so that nylon tricot backing is oriented toward hand 119 Component missing or not securely affixed 120 Mend in leather or fabric (i.e, patch not applicable to restitched seam repair) 121 Needle chews likely to develop into a hole 122 Seams and S

9、titching Open seam: - In single stitched seam - In any row of a double stitched seam -not repaired as specified (when applicable) 123 124 213 23Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32173 TABLE XII. End Item Visual Defects -Continue

10、d Examine Defect ClassificationMajor Minor NOTE: A seam shall be classified as open when one or more stitches joining a seam are broken or when two or more consecutive skipped or run-off stitches occur. Not specified seam type 125 Not specified stitch type 126 Row of stitching omitted 127 Loose stit

11、ch tension resulting in a loosely secured seam 128 Tight stitch tension resulting in cutting of leather or fabric or breaking of stitches when normal pull is applied 129 Ends of stitching not secured as specified 214 Gage of stitching irregular or not as specified, affecting Appearance 130 Part caug

12、ht in unrelated row of stitching 131 One or two stitches per inch less than specified 215 Three or more stitches per inch less than specified 132 Leather or fabric torn by needles (elongated holes) - up to 1/2 inch - greater than 1/2 inch 216 133 24Provided by IHSNot for ResaleNo reproduction or net

13、working permitted without license from IHS-,-,-MIL-DTL-32173 TABLE XII End Item Visual Defect Continued Examine Defect Classification Major Minor Not backstitched where required 134 More than the specified maximum number of stitches per inch: - damaging materials - not damaging materials 135 217 Ass

14、embly Detail Glove not neatly laid off: - wrinkles in shell - fingers not completely opened 218 136 No inseam construction where specified 137 Finished measurement across folded area of any fingertip less than specified: - up to 1/16 inch less - greater than 1/16 inch less 219 138 Welt omitted on ba

15、ck 139 Welt is more than 1/8 inch from either side seam 220 Welt not completely caught in finger back/hand back seam 221 Welt caught in closing seam 222 Pleats missing from any finger (does not include thumb) 140 Shell more than 1/8 inch longer than lining in any finger when on hand or on flat surfa

16、ce 141 25Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32173 TABLE XII End Item Visual Defects -Continued Examine Defect Classification Major Minor Poorly assembled seriously affecting serviceability (e.g., finger distorted or twisted affec

17、ting comfort of wearer or causing seam finger to come in contact with object) 142 NOTE: Any construction defect that results in a malformed glove such as a twisted finger or thumb resulting in any seam lying in the palmar area of the finger or thumb is a major defect. When a finger or thumb is twist

18、ed and the seam is rotated to less than 45 degrees from the vertical and does not lie in the palmar area, it is a minor defect Poorly assembled affecting serviceability but not seriously (e.g., pleats on palm or thumb back created when attaching palm patch, fabric not distributed evenly under elasti

19、c take-ups, wrist elastic misaligned at side seams etc.) 223 Edge of pleat not fully caught in closing seam - less than 1/16 inch - more than 1/16 inch 224 143 Lining not securely fastened to shell at side of fingertips 144 Knit cuff seam not caught in cuff hem 145 26Provided by IHSNot for ResaleNo

20、reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32173 TABLE XII End Item Visual Defects - Continued Examine Defect Classification Major Minor Thread ends not trimmed throughout glove 225 Not constructed with specified number of pieces 146 Difference in overall length betwee

21、n front and back of glove is more than 1/2 inch 147 Elastic webbing across back of Hand and at wrist not fully caught in closing seam 148 Label and Instruction Slip Omitted, incorrect, illegible, or misplaced; size and identification label not securely sewn in seam 226 4.4.4 End item dimensional exa

22、mination. The end item shall be examined for conformance to the dimensions specified in Table VIII, 3.11 and 3.12. Any dimension not within the specified tolerance shall be classified as a Major defect. The defect number shall be 149. The lot size shall be expressed in units of gloves. The sample un

23、it shall be one glove and the selection shall be by pairs. 5. PACKAGING 5.1 Packaging. For Acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of material is to be performed by DoD or in-house contractor personnel, these personnel

24、 need to contract the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieva

25、l is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.” 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 27Prov

26、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32173 6.1 Intended use. The glove covered by this Specification is intended to be worn by military aircrew requiring an intermediate level of cold weather protective handwear. 6.2 Acquisition requir

27、ements. Acquisition documents must specify the following: a. Title, number, and date of this specification. b. Sizes required (see 1.3). c. Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.2.1 and 2.3). d. When first artic

28、le is required (see 3.1, 4.2 and 6.3). e. Packaging requirements (see 5.1). 6.3 First article. When a first article is required, it will be inspected and approved under the appropriate provisions of FAR 52.209. The first article should be a preproduction sample. The contracting officer should specif

29、y the appropriate type of first article and the number of units to be furnished. The contracting officer should include specific instructions in all acquisition instruments regarding arrangements for selection, inspection, and approval of the first article. 6.4 Patterns. For access to patterns, addr

30、ess the acquiring activity issuing the invitation for bids. 6.5 Source of supply 6.5.1 Lining fabric. Finished lining fabric meeting the requirements of 3.3.3.4 is available from: International Foam Products, Inc. 771 Commercial Avenue Carlstadt, NJ 07072 6.5.2 Knit cuffs. Knit cuffs meeting the req

31、uirements of 3.3.4 are available from: St. Regis Sportswear 51 Beaver Street Gloversville, NY 12078 6.6 Patent notice. U.S. Patent number 4654896 covers the Flexor design of this item as described in 3.6 of this specification. The Government does not have a royalty-free license for this patent. Info

32、rmation regarding licensing for production of gloves meeting this specification may be obtained from: Rinehart Glove Ltd. P.O. Box 3400 Montrose, CO 81401 28Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32173 6.7 Pattern Numbers. The patter

33、ns listed in 3.7.1 have been identified with a NAVAIR drawing number for the purpose of configuration control and tracking of pattern changes. These numbers range from 3526AS190-(1 to 13) through 3526AS196-(1 to 13). These numbers do not have any effect on manufacturing. 6.8 Subject terms (key word) listing. Cold Weather Gloves 29Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32173 Figure 1 HAU-15/P Glove Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS30-,-,-