DLA MIL-DTL-32182-2005 COAT OPERATIONAL DRESS UNIFORM (COAST GUARD)《业务着装制服大衣(海岸警卫队)》.pdf

1、INCH-POUNDMIL-DTL-32182 January 12, 2005 DETAIL SPECIFICATION COAT, OPERATIONAL DRESS UNIFORM (COAST GUARD) This document is approved for use by authorized personnel of the United States Coast Guard. 1. SCOPE 1.1 Scope. This document covers the requirements for single-breasted coats. 1.2 Classificat

2、ion. The coat will be of one type in the following sizes as specified (see 6.2). TABLE I. Schedule of sizes XX-SHORT X-SHORT SHORT REGULAR LONG X-LONG XX-LONG- 32 32 32 32 - - - - - 33 - - - 34 34 34 34 34 34 - 36 36 35 35 35 - - 38 38 36 36 36 36 - 40 40 37 37 37 - - - 42 38 38 38 38 38 - 44 39 39

3、39 39 - - - 40 40 40 40 40 - - 41 41 41 41 - - - 42 42 42 42 42 - - 43 43 43 43 - - - 44 44 44 44 44 - - - 45 45 45 - - - 46 46 46 - - - - - 47 47 - - Comments, suggestions, or questions on this document should be addressed to the Defense Supply Center Philadelphia, DSCP-CRFD, 700 Robbins Avenue, Ph

4、iladelphia, PA 19111, or e-mailed to Elizabeth.Gladstonedla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST online database at http:/assist.daps.dla.mil. AMSC N/A FSC 8415 Provided by IHSNot for ResaleNo reproduction or netw

5、orking permitted without license from IHS-,-,-MIL-DTL-32182 2TABLE I. Schedule of sizes, cont. XX-SHORT X-SHORT SHORT REGULAR LONG X-LONG XX-LONG- - - 48 48 - - - - - 50 50 - 50 - - - 52 52 - 52 - - - 54 54 - - - - - - 56 - - - - - - 58 - - - - - - 60 - - 2. APPLICABLE DOCUMENTS 2.1 General. The doc

6、uments listed in this section are specified in sections 3, 4 or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this

7、 list, document users are cautioned that they must meet all specified requirements cited in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form

8、a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). COMMERCIAL ITEM DES

9、CRIPTION A-A-55126 Fastener, Tapes, Hook and Loop, Synthetic DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-C-44436 Cloth, Camouflage Pattern, Wind Resistant Poplin, Nylon/Cotton Blend (Copies of these documents are available online at http:/assist.daps.dla.mil or from the Standardization Document Order D

10、esk, 700 Robbins Avenue, Building #4, Section D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contra

11、ct. (See 6.2). ASTM INTERNATIONAL ASTM D-2256 Tensile Properties of Yarns by the Single-Strand Method ASTM D-6193 Standard Practice for Stitches and Seams Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32182 3(Copies of these documents are a

12、vailable from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or from www.astm.org.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS AATCC 61 Colorfastness to Laundering, Home and Commercial: Accelerated AATCC 136 Bond Strength of Bonded

13、 and Laminated Fabrics (Copies of these documents are available from the American Association of Textile Chemists and Colorists, P.O. Box 12215, Triangle Park NC 27709-2215 or from www.aatcc.org. Phone number (919) 549-8141.) ANSI/ASQC Z1.4 Sampling Procedures and Tables for Inspection of Attributes

14、 (Copies of these documents are available the American National Standards Institute, 1430 Broadway, New York, NY 10018-3308 or from www.ansi.org.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes pr

15、ecedence. Nothing in this document however, supersedes applicable laws and regulations unless a specified exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.2. 3.2 Recycled r

16、ecovered or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle cos

17、ts. 3.3 Design and construction. The coat is single-breasted with a collar, concealed button front closure, 2 breast pockets with flaps, and there shall be no exposed drill holes. The left breast pocket has a concealed pencil pocket. The coat has long sleeves with reinforced elbows, adjustable cuffs

18、 at wrist, a suppressed waist and a straight-cut bottom (reference figure 1). 3.4 Basic material. The basic material shall be nylon/cotton ripstop dyed USCG Blue 3362, conforming to the physical properties for Class 1 of MIL-C-44436. The coat shall show no toxicity when used as intended and when tes

19、ted as specified in 4.4. 3.5 Seconds/mill seconds. Seconds/mill seconds cloth shall be dyed in conformance with the specified basic material and shall meet the physical, mechanical, and dimensional requirements of the respective finished fabric. Seconds shall be cloth which has been rejected for def

20、ects pertaining to color only, as cited in the specified basic material requirements. Mill seconds shall be cloth which has been rejected for visual defects only and has been dyed to match specified basic material. (See 3.10). Provided by IHSNot for ResaleNo reproduction or networking permitted with

21、out license from IHS-,-,-MIL-DTL-32182 43.6 Components 3.6.1 Interlining. To improve abrasion resistance and appearance of garment, the collar and pocket flaps shall be interlined. The interlining shall have the same life expectancy of the coat itself. After attaching to the basic cloth, it shall me

22、et an initial directional bond strength of 32 ounces minimum per inch, and after 3 launderings, it shall meet a directional bond strength of 24 ounces minimum per inch when tested as specified in 4.4.1. 3.6.2 Thread and gimp. 3.6.2.1 Thread. Thread for needle and bobbin (looper) shall be cotton or p

23、olyester-covered, polyester core, commercial size Ticket No. 50 (Tex size 36 to 50) with a minimum breaking strength of 3.2 pounds when tested as specified in 4.4.2. As an alternate, Ticket No. 70 (Tex size 31 to 35) with a breaking strength of 2.6 pounds when tested as specified in 4.4.2 may be use

24、d as the bobbin (looper) thread. The color shall be black. 3.6.2.2 Gimp. Thread for reinforcement of buttonholes shall be cotton, commercial size Ticket No. 8 (Tex size 210) with a minimum breaking strength of 6.5 pounds when tested as specified in 4.4.2. The color shall be black. 3.6.2.3 Colorfastn

25、ess. All thread used shall be non-staining and show good colorfastness to laundering when tested as specified in 4.4.3. 3.6.3 Fastener tape (hook any part of coat caught in any unrelated stitching, the edge of any component part required to be forced out having folds of more than 1/8 inch Cloth: hol

26、e, cut, tear, smash, burn, drill hole, run, thin place, dye streak, color not as specified, misweave, knot or slub affecting appearance or serviceability Seam: puckered, distorted, pleated, wavy, twisted, irregular, open, loose or tight stitch tension, broken or missing thread or stitch, needle chew

27、 visible mend, edge or raised stitching sewn too close to edge, resulting in damage to cloth, seam allowance not as specified raw edge affecting appearance or serviceability Length of fronts uneven by more than 1/4 inch at top or uneven by more than 1/4 inch at bottom when buttoned, front buttons a

28、nd buttonholes out of alignment, causing bulge or twist on fronts when buttoned Permanent fold, pleat, or crease affecting appearance or serviceability Front pockets and flaps not uniform in size or shape, out of alignment by more than 3/8 inch, front edge not parallel to front of coat by 3/8 inch o

29、r more, pleated, twisted, curled or puckered, not stitched as specified, flap not completely covering pocket opening, Hook and loop out of alignment causing bulge or twist on pockets when fastened Collar points: uneven in length by 1/4 inch or more, collar curls, puckers, pleats, or twists Buttonhol

30、es: added, not clean cut or securely caught in fabric, not specified type Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32182 13EXAMINATION DEFECT Buttons: missing, broken, defective, not attached as specified, or insecurely sewn. Bartacks

31、or backtacks: missing, insecure, misplaced, not specified size, stitches loose or broken, or not serving intended purpose Fastener tape: missing, defective, incorrect style or color, not attached or sewn as specified. Sleeve: reversed, puckered or pleated; cuffs reversed, uneven in width more than 1

32、/4 inch, poorly shaped, buttons not placed as specified, cuff buttonhole and first sleeve button not aligned, causing bulge or twist on cuff when buttoned Interlining: bubbling, delamination, bleed through, wrinkling, or puckering Any finished measurement not as specified Shade Shade variation withi

33、n a part or between parts Thread or button color not as specified Cleanness Spot, stain, excessive thread ends not trimmed or removed Odor, affecting appearance or serviceability Labels Labels: omitted, incorrect, illegible, not attached where specified Bar code/UPC code omitted, not readable by sca

34、nner; human-readable interpretation (HRI) omitted or illegible Bar code/UPC code not visible on folded, packaged item, bar code attachment causes damage to the item Packaging Any coats not packaged in accordance with contract or purchase order 4.4.4.1 Finished dimensions. The coat shall conform to t

35、he dimensions listed below: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32182 14TABLE VII. Finished dimensions All measurements in inches. EVEN SIZES XX-SHORT 34 36 38 40 HALF CHEST + 3/8 in. 21 22 23 24 HALF WAIST + 3/8 in. 18-1/4 19-1/4

36、 20-1/4 21-1/4 HALF SEAT + 3/8 in. 20 21 22 23 CUFF + in. 15-7/8 16-1/8 16-3/8 16-5/8 SLV. LENGTH + in. 30-1/2 30-1/2 31 31 BODY LENGTH + in. 28-1/4 28-1/2 28-3/4 29 X-SHORT 32 34 36 38 40 42 44 HALF CHEST + 3/8 in. 20 21 22 23 24 25 26 HALF WAIST + 3/8 in. 17-1/4 18-1/4 19-1/4 20-1/4 21-1/4 22-1/4

37、23-1/4 HALF SEAT + 3/8 in. 19 20 21 22 23 24 25 CUFF + in. 15-5/8 15-7/8 16-1/8 16-3/8 16-5/8 16-7/8 17-1/8 SLV. LENGTH + in. 31 31-1/2 31-1/2 32 32 32-1/2 32-1/2 BODY LENGTH + in. 29 29-1/4 29-1/2 29-3/4 30 30-1/4 30-1/2 SHORT 32 34 36 38 40 42 44 46 48 HALF CHEST + 3/8 in. 20 21 22 23 24 25 26 27

38、28 HALF WAIST + 3/8 in. 17-1/4 18-1/4 19-1/4 20-1/4 21-1/4 22-1/4 23-1/4 24-1/4 25-1/4 HALF SEAT + 3/8 in. 19 20 21 22 23 24 25 26 27 CUFF + in. 15-5/8 15-7/8 16-1/8 16-3/8 16-5/8 16-7/8 17-1/8 17-3/8 17-5/8 SLV. LENGTH + in. 32 32-1/2 32-1/2 33 33 33-1/2 33-1/2 34 34 BODY LENGTH + in. 30 30-1/4 30-

39、1/2 30-3/4 31 31-1/4 31-1/2 31-3/4 32 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32182 15REGULAR 32 34 36 38 40 42 44 46 48 50 52 54 HALF CHEST + 3/8 in. 20 21 22 23 24 25 26 27 28 29 30 31 HALF WAIST + 3/8 in. 17-1/4 18-1/4 19-1/4 20-1/

40、4 21-1/4 22-1/4 23-1/4 24-1/4 25-1/4 26-1/4 27-1/4 28-1/4 HALF SEAT + 3/8 in. 19 20 21 22 23 24 25 26 27 28 29 30 CUFF + in. 15-5/8 15-7/8 16-1/8 16-3/8 16-5/8 16-7/8 17-1/8 17-3/8 17-5/8 17-7/8 18-1/8 18-3/8 SLV. LENGTH + in. 33-1/2 34 34 34-1/2 34-1/2 35 35 35-1/2 35-1/2 36 36 36-1/2 BODY LENGTH +

41、 in. 31-1/2 31-3/4 32 32-1/4 32-1/2 32-3/4 33 33-1/4 33-1/2 33-3/4 34 34-1/4 LONG 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 HALF CHEST + 3/8 in. 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 HALF WAIST + 3/8 in. 17-1/4 18-1/4 19-1/4 20-1/4 21-1/4 22-1/4 23-1/4 24-1/4 25-1/4 26-1/4 27-1/4 28-1/4 29

42、1/4 30-1/4 31-1/4 HALF SEAT + 3/8 in. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 CUFF + in. 15-5/8 15-7/8 16-1/8 16-3/8 16-5/8 16-7/8 17-1/8 17-3/8 17-5/8 17-7/8 18-1/8 18-3/8 18-5/8 18-7/8 19-1/8 SLV. LENGTH + in. 34-1/2 35 35 35-1/2 35-1/2 36 36 36-1/2 36-1/2 37 37 37-1/2 37-1/2 38 38 BODY LENG

43、TH + in. 33 33-1/4 33-1/2 33-3/4 34 34-1/4 34-1/2 34-3/4 35 35-1/4 35-1/2 35-3/4 36 36-1/4 36-1/2 X-LONG 34 36 38 40 42 44 HALF CHEST + 3/8 in. 21 22 23 24 25 26 HALF WAIST + 3/8 in. 18-1/4 19-1/4 20-1/4 21-1/4 22-1/4 23-1/4 HALF SEAT + 3/8 in. 20 21 22 23 24 25 CUFF + in. 15-7/8 16-1/8 16-3/8 16-5/

44、8 16-7/8 17-1/8 SLV. LENGTH + in. 36 36 36-1/2 36-1/2 37 37 BODY LENGTH + in. 34-3/4 35 35-1/4 35-1/2 35-3/4 36 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32182 16XX-LONG 38 40 42 44 50 52 HALF CHEST + 3/8 in. 23 24 25 26 29 30 HALF WAIS

45、T + 3/8 in. 20-1/4 21-1/4 22-1/4 23-1/4 26-1/4 27-1/4 HALF SEAT + 3/8 in. 22 23 24 25 28 29 CUFF + in. 16-3/8 16-5/8 16-7/8 17-1/8 17-7/8 18-1/8 SLV. LENGTH + in. 37-1/2 37-1/2 38 38 39 39 BODY LENGTH + in. 36-3/4 37 37-1/4 37-1/2 38-1/4 38-1/2 ODD SIZES SHORT 35 37 39 41 43 HALF CHEST + 3/8 in. 21

46、22 23 24 25 HALF WAIST + 3/8 in. 18 19 20 21 22 HALF SEAT + 3/8 in. 22 23 24 25 26 CUFF + in. 15-1/8 15-3/8 15-5/8 15-7/8 16-1/8 SLV. LENGTH + in. 29 29 29 29 29 BODY LENGTH + in. 28-1/4 28-1/2 28-3/4 29 29-1/4 REGULAR 33 35 37 39 41 43 45 47 HALF CHEST + 3/8 in. 20 21 22 23 24 25 26 27 HALF WAIST + 3/8 in. 17 18 19 20 21 22 23 24 HALF SEAT + 3/8 in. 21 22 23 24 25 26 27 28 CUFF + in. 14-7/8 15-1/8 15-3/8 15-5/8 15-7/8 16-1/8 16-3/8 16-5/8 SLV. LENGTH + in. 31 31 31 31 31 31 31 31 BODY LENGTH + in. 29 29-1/4 29-1/2 29-3/4 30 30-1/4 30-1/2 30-3/4 Provided b