DLA MIL-DTL-38999 34 D-2008 CONNECTORS RECEPTACLE ELECTRICAL CIRCULAR BREAKAWAY JAMNUT MOUNTING REMOVABLE CRIMP CONTACTS SOCKETS SERIES III SHELL SIZE 25 METRIC《米制III系列外形尺寸25的可拆卸压接.pdf

1、 METRIC MIL-DTL-38999/34D 10 July 2008 SUPERSEDING MIL-DTL-38999/34C 1 September 2006 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, CIRCULAR, BREAKAWAY, JAMNUT MOUNTING, REMOVABLE CRIMP CONTACTS, SOCKETS, SERIES III, SHELL SIZE 25, METRIC This specification is approved for use by al

2、l Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-38999. FIGURE 1. Receptacle, classes P, R, T, W, X and Z. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or netwo

3、rking permitted without license from IHS-,-,-MIL-DTL-38999/34D 2 FIGURE 1. Receptacle, classes P, R, T, W, X and Z Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-38999/34D 3 mm Inches mm Inches mm Inches mm Inches .03 .001 .58 .02

4、3 3.0 .12 32.5 1.28 .10 .004 .7 .03 3.58 .141 42.8 1.68 .13 .005 .87 .034 12.7 .50 42.85 1.69 .15 .006 1.5 .06 13.2 .52 44.4 1.75 .3 .01 1.91 .075 14.3 .56 55.6 2.19 .4 .02 1.98 .078 22.6 .89 58.7 2.31 NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are given for information only. 3. Pa

5、nel thickness: 3.2 - 1.58 mm. 4. Alternates O-ring material may be in accordance with SAE-AMS3325. 5. C and J dimensions define feature required for proper fit in type E panel. 6. F diameter and P dimensions defines G thread start. 7. Countersink may be incorporated to accept accessory configuration

6、 in accordance with MIL-DTL-38999. 8. B flat orientation. 9. For details of connector front and rear configurations, see MIL-DTL-38999. FIGURE 1. Receptacle, classes P, R, T, W X and Z Continued. REQUIREMENTS: Dimensions and configurations: See figure 1. Interface dimensions shall conform to MIL-DTL

7、-38999. This receptacle is designed for use with lanyard release plug and mates with MIL-DTL-38999/29, /30, and /31. It is intended to be used only on stores. Insert arrangement: See MIL-STD-1560. Separation force: The receptacle shell shall break into two parts when a separation force is applied at

8、 any angle within 15 of the normal axis by the mating plug assembly. Separation shall occur such that the plug assembly shall be pulled free of the receptacle insert and contacts shall remain secure in the mounted part. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

9、ense from IHS-,-,-MIL-DTL-38999/34D 4 Part or Identifying Number (PIN) example: D38999/ 34 W 20 A Military prefix Specification sheet number Class Insert arrangement Polarizing positions N is required for normal position QUALIFICATION: Qualification is required. Qualifications shall be in accordance

10、 with MIL-DTL-38999 with the following exceptions: Group I: Durability: Wired connectors shall meet the durability requirements of MIL-DTL-38999, with the following exceptions: The total number of cycles of mating and unmating shall be 500, in the following sequences: 200 cycles of normal mating and

11、 unmating, 50 cycles of normal mating with pull-separation unmating, 200 cycles of normal mating and unmating, 50 cycles of normal mating with pull-separation unmating. The lanyard release velocity during the pull-separation force unmating cycles shall be 9.15 meters per second. Separation force: Up

12、on conclusion of the group I test, all samples shall be subjected to an axial force applied by a mated plug assembly. The connector shall meet the requirements of separation force when the applied load is 1,800 200 Newton. External bending moment: Wired connectors shall meet external bending moment

13、requirements of MIL-DTL-38999 with the following exception: Size 25 loading shall be 28.3 Newton-meters. Group II: Durability: Wired connectors shall meet the durability requirements of MIL-DTL-38999, with the following exceptions: The total number of cycles of mating and unmating shall be 500, in t

14、he following sequences: 200 cycles of normal mating and unmating, 50 cycles of normal mating with pull-separation unmating, 200 cycles of normal mating and unmating, 50 cycles of normal mating with pull-separation unmating. The lanyard release velocity during the pull-separation force unmating cycle

15、s shall be 9.15 meters per second. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-38999/34D 5 Vibration: Wired connectors shall meet the vibration requirements of MIL-DTL-38999 with the following exceptions: Sine vibration: Connectors shall

16、be subjected to the test specified in method 204, test condition G, of MIL-STD-202. Random vibration: Connectors shall be subjected to the test specified in test procedure EIA-364-28, test condition VI, letter J, ambient temperature. Duration shall be 8 hours in the longitudinal direction and 8 hour

17、s in a perpendicular direction, for a total of 16 hours. The qualifying activity will define the accessory load and cable to be used in the random and sine vibration tests. Separation force: Upon conclusion of the group II test, all samples shall be subjected to an axial force applied by a mated plu

18、g assembly. The connector shall meet the requirements of separation force when the applied load is 1,800 200 Newton. External bending moment: Wired connectors shall meet external bending moment requirements of MIL-DTL-38999 with the following exception: Size 25 loading shall be 28.3 Newton-meters. C

19、hanges from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-38999, this document references the following: MIL-DTL-38999/29 MIL-DTL-38999/30 MIL-DTL-

20、38999/31 MIL-STD-202 MIL-STD-1560 SAE-AS3582 SAE-AMS3325 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-38999/34D 6 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA CC DLA CC (Project 59352008-023) Review activities: Ai

21、r Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change. You should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-