DLA MIL-DTL-39024 11 G-2012 JACK TIP TEST POINT TYPE PRINTED WIRING TYPE SINGLE TEST POINT RIGHT ANGLE 2-LEG MOUNTING LOW VOLTAGE 080.pdf

1、AMSC N/A FSC 5935 MIL-DTL-39024/11G 2 July 2012 SUPERSEDING MIL-J-39024/11F 13 April 1993 DETAIL SPECIFICATION SHEET JACK, TIP, TEST POINT TYPE, PRINTED WIRING TYPE, SINGLE TEST POINT, RIGHT ANGLE, 2-LEG MOUNTING, LOW VOLTAGE, .080 This specification is approved for use by all Departments and Agenci

2、es of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-39024. FIGURE 1. Configuration and dimensions. Inches mm .030 0.76 .052 1.32 .078 1.98 .088 2.24 .156 3.96 .200 5.08 .400 .460 10.16 11.68 MOUNTING TO FI

3、T .052 DIA HOLE SEE OPERATING NOTES A .156 B TOP HOLE 088 MAX DIA (SEE TABLE I) .078 .200 .460 .400 +.02 -.01 .030 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/11G 2 NOTES: 1. Dimensions are in inches. (See table I for dim

4、ensions not shown on figure 1). 2. Unless otherwise specified, tolerances are .010 (0.25 mm). 3. Metric equivalents are given for information only. 4. Terminal contour is optional provided that mounting hole and mounting center requirement are set. Also see terminal bendability requirements. 5. Top

5、hole provides access to the electrical contact for a hand held probe. There is no spring contact retention. 6. All un-dimensioned pictorial configurations are for reference purposes only. FIGURE 1. Configuration and dimensions Continued. TABLE I. Design and identification data. Dash number 2/ 3/ Dim

6、ensions (inches) 1/ Insulation Hole Configuration A .010 (0.25) B .015 (0.38) C .015 (0.38) Color Number in accordance with FED-STD-595/ -01X 4/ -02X -03X -04X -05X -06X -07X -08X -09X -10X .220 (5.59) “ “ “ “ “ “ “ “ 0.130 (3.30) “ “ “ “ “ “ “ “ 0.130 (3.30) “ “ “ “ “ “ “ “ White Red Black Brown Gr

7、een Orange Blue Yellow Gray Purple 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - Side holes only -41X -42X -43X -44X -45X 46X 47X 48X 49X -50X .220 (5.59) “ “ “ “ “ “ “ “ .130 (3.30) “ “ “ “ “ “ “ “ .130 (3.30) “ “ “ “ “ “ “ “ White Red Black Brown Green Orange Blue Yellow Gray Purpl

8、e 17875 11105 17038 10075 14110 12246 15123 13655 16187 27144 - Top and side holes -71X 5/ -72X -73X -74X -75X -76X -77X -78X -79X -80X .220 (5.59) “ “ “ “ “ “ “ “ .130 (3.30) “ “ “ “ “ “ “ “ .130 (3.30) “ “ “ “ “ “ “ “ White Red Black Brown Green Orange Blue Yellow Gray Purple 17875 11105 17038 100

9、75 14110 12246 15123 13655 16187 27144 - Side holes only See footnotes on next page. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/11G 3 TABLE I. Design and identification data Continued. 1/ Dimensions are in inches. Metric equivalent

10、s are given for information only. 2/ Dash numbers -21 through -30 have been deleted. See Table II for recommended substitutes. Dash numbers -51 through -70 have been canceled without replacement. 3/ X = G For parts with gold plated terminals. (OEMs may order parts with gold plated terminals, marked

11、with the suffix “G”, and request that the terminals be solder dipped as a post manufacturing operation.) X = blank for parts with any of the specified terminal finishes. (OEMs may identify a specific terminal finish in their purchase order.) 4/ Dash numbers -01X through -10X are for use by OEMs. Whe

12、n a qualified products list source is available for dash number -71X through -80X, only they will be acquired by the government for stock and issue in place of dash numbers -01X through -10X, respectively. 5/ Clinchable terminals. See terminal bendability requirements. REQUIREMENTS: Design and const

13、ruction: Dimensions and configuration: See figure 1 and table I. Insulation: Material shall be polyamide in accordance with L-P-410 or ASTM D4066. Test probe: 0.080 0.001 inch (2.03 0.03 mm ) in diameter (connector shall accept test probe from either end). Test probe shall be engaged a minimum of .4

14、50 inches. Test probe shall be fully inserted. Insulation resistance: Test circuit figure in MIL-DTL-39024 shall be used. Dielectric withstanding voltage (at sea level): Test circuit figure in MIL-DTL-39024 shall be used. The applicable voltage shall be applied for 15 seconds. For -01X through -10X,

15、 2000 volts rms, 60Hz, -41X through -50X, 500 volts rms, 60Hz, -71X through -80X, 2000 volts rms, 60 Hz. Insulation and withdrawal forces Insertion force: 5.0 pounds (maximum) Withdrawal force: 0.5 pounds (minimum) Terminal bendability: for -71X through -80X, when the part is seated on a .0625 inch

16、(1.588mm) nominal thickness printed wiring board there shall be no breakage or visible fracture of the terminals when they are clinched parallel to the board surface. Identification marking: The marking shall be located on the immediate container. Part or Identifying Number (PIN): M39024/11-(dash nu

17、mber from table I). G on parts furnished to the government. The suffix “G” shall be used to identify parts with gold plated terminals. OEMs may order parts with or without gold plated terminals and mark them according to footnote 3 in table I. Effective date of this revision, all parts furnished to

18、the government for stock and issue shall have gold plated Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/11G 4 terminals. Existing government stocks of non-gold terminal items shall be issued until exhausted. However, only “G” suffix i

19、tems will be purchased. “G” suffix may be added to existing M39024/11-XX PINs Lacking “G” suffix. New NSNs will not be assigned. Operating conditions: Operating voltage: 1,500 volts rms, 60 hertz at sea level; 350 volts rms, 60 hertz at 50,000 feet. Maximum thickness of unsupported printed wiring bo

20、ard on which the connector may be used is .0625 inch (1.588mm). Maximum thickness of printed wiring board with plated through hole is .0930 inch (2.352mm). Qualification: Not applicable. Conformance inspection. Groups A and B tests in accordance with MIL-DTL-39024 shall be applicable. Substitution d

21、ata. See table II. TABLE II. Substitution data. Deleted dash numbers Recommended substitute (dash numbers) -21 -01 -22 -02 -23 -03 -24 -04 -25 -05 -26 -06 -27 -07 -28 -08 -29 -09 -30 -10 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where c

22、hanges from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of th

23、e marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-39024/11G 5 Referenced documents. In addition to MIL-DTL-39024, this document references the following: CONCLUDING MATERIAL Cust

24、odians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force 85 DLA - CC (Project 5935-2009-148) Review activities: Army - AR, CR4, MI Navy - AS, CG, MC, YD Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of this document. Since organizations and respon

25、sibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. ASTM D4066 L-P-410 FED-STD-595/17875 FED-STD-595/11105 FED-STD-595/17038 FED-STD-595/10075 FED-STD-595/14110 FED-STD-595/12246 FED-STD-595/15123 FED-STD-595/13655 FED-STD-595/16187 FED-STD-595/27144 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-