DLA MIL-DTL-3922 52 D-2010 FLANGES WAVEGUIDE (PRESSURIZABLE CONTACT).pdf

1、AMSC N/A FSC 5985 MIL-DTL-3922/52D 16 March 2010 SUPERSEDING MIL-F-3922/52C 6 March 2000 DETAIL SPECIFICATION SHEET FLANGES, WAVEGUIDE (PRESSURIZABLE CONTACT) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the flang

2、es described herein shall consist of this specification sheet and MIL-DTL-3922. FIGURE 1. Flange. INCH-POUND C A B TOL V MP DIA.8 PLSCBOREDD DIA. X .060 DEEPAA .02D TOTALBREAKSHARPCORNERSUTZAA.010.003BBCCEEGG45 .5 GGHH- A -C A TDL JJ C B TDL JJ AFF- A - TDL KKGROOVED FLANGESECTION A-AFLAT FACEDFLANG

3、E4 SIDES 63 B .090 .0304 PLS HH ALTERNATE CORNER CONSTRUCTION- B - CMARKINGE ED DKF DIA.2 PLSNYLMSECTION B-BC A B TOL J MA .TOL X TOTALA .004 TOTALA .004 TOTAL SRB .004 TOTALB .004 TOTALA .020 TOTAL B .020 TOTALB TOL X TOTAL BProvided by IHSNot for ResaleNo reproduction or networking permitted witho

4、ut license from IHS-,-,-MIL-DTL-3922/52D 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are based upon 1.00 inch = 25.4 mm. 3. Mating surfaces, including seal groove, shall not exceed 63 microinches in accordance with A

5、SME B46.1, except that flaws shall be included in the roughness height measurement. 4. Flat face flanges require a metal-rubber seal at the junction. These seals are covered by MIL-DTL-24211. 5. For lettered dimensions, see table I. 6. Counterbore of the eight holes is not required when flanges are

6、made from bar stock. Inches mm .003 0.08 .004 0.10 .010 0.25 .020 0.51 .030 0.76 .040 1.02 .060 1.52 .090 2.29 TABLE I. Dash numbers and dimensions. PIN M3922/52- 1/ Dimensions 2/ Dash Used with Dash Used with No. 3/ Waveguide M85/1- Mating flange No 4/ Waveguide M85/1- MatingflangeA B C .02 (0.51)

7、D BSC E BSC F Dia. G BSC 001 023 015 017 5/ 002 024 018, 019, 168 5/ 6.500 .005 (165.10) (0.13)3.250 .005 (82.55) (0.13)8.69 (220.73)1.249 (31.72) 2.311 (58.70) .330 .005(8.38) (0.13)2.374 (60.30)003 025 021 023 “ 004 026 025, 026, 169 “ 5.100 .005 (129.54) (0.13)2.550 .005 (64.77) (0.13)7.16 (181.8

8、6)1.031 (26.19) 1.925 (48.90) .266 .005(6.76) (0.13)1.987 (25.07)005 027 027 031 “ 006 028 029, 030, 170 “ 4.300 .005 (109.22) (0.13)2.150 .005 (54.61) (0.13)6.34 (161.04).938 (23.82) 1.720 (43.69) “ 1.787 (45.39)007 029 033 037 “ 008 030 035, 036, 171 “ 3.400 .005 (86.36) (0.13) 1.700 .005 (43.18)

9、(0.13)5.44 (138.18).671 (17.04) 1.500 (38.10) “ 1.344 (34.14)009 031 039 043 “ 010 032 041, 042, 172 “ 2.840 .005 (72.14) (0.13) 1.340 .005 (34.04) (0.13)4.50 (114.30).578 (14.68) 1.164 (29.57) .257 .003(6.53) (0.08)1.281 (32.54)011 033 045 049 “ 012 034 047, 048, 173 “ 2.290 .005 (58.17) (0.13) 1.1

10、45 .005 (29.08) (0.13)3.88 (98.55).500 (12.70) 1.050 (26.67) .257 .002(6.53) (0.05)1.070 (27.18)013 035 051 055 “ 014 036 053, 054, 174 “ 1.872 .005 (47.55) (0.13) .872 .005 (22.15) (0.13)3.50 (88.90).438 (11.12) .914 (23.22) - .563 (14.30)015 037 057 061 “ 016 038 059, 060, 175 “ 1.590 .004 (40.39)

11、 (0.10) .795 .004 (20.19) (0.10)3.19 (81.03).375 (9.52) .875 (22.22) - .500 (12.70)017 039 063 067 “ 018 040 065, 066, 176 “ 1.372 .004 (34.85) (0.10) .622 .004 (15.80) (0.10)2.69 (68.33).313 (7.95) .719 (18.26) - .438 (11.12)019 041 069 073 “ 020 042 071, 072, 177 “ 1.122 .004 (28.50) (0.10) .497 .

12、004 (12.62) (0.10)2.50 (63.50)” .640 (16.26) - .375 (9.52) 021 043 075 079 “ 022 044 077, 078, 178 “ .900 .003 (22.86) (0.08) .400 .003 (10.16) (0.08)2.09 (53.09)“ .578 (14.68) - .312 (7.92) See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without l

13、icense from IHS-,-,-MIL-DTL-3922/52D 3 TABLE I. Dash numbers and dimensions - Continued. Dimensions 2/ Dash No. 3/ Dash No. 4/ H BSC J K .02 (0.51) L .02 (0.51) M N .004 (0.10) P Dia. R .02 (0.51) S T .004 (0.10) U .004 (0.10) 001 023 002 024 3.937 (100.00) .012 (0.30) 5.44 (138.18) 3.81 (96.77) 3.4

14、20 -.001 (86.87) (0.03) +.000 3.630 (92.20).330 .005 (8.38) (0.13)7.06 (179.32)6.670 -.001 (169.42) (0.03) +.000 6.880 (174.75)7.452 (189.28)003 025 004 026 3.200 (81.28) .011 (0.28) 4.62 (117.35) 3.10 (78.74) 2.720 -.001 (69.09) (0.03) +.000 2.920 (74.17).266 .005 (6.76) (0.13)5.67 (144.02)5.270 -.

15、001 (133.86) (0.03) +.000 5.470 (138.94)6.042 (153.47)005 027 006 028 2.795 (71.00) “ 4.19 (106.43) 2.69 (68.33) 2.320 -.001 (58.93) (0.03) +.000 2.510 (63.75)“ “ 4.88 (123.95)4.470 -.001 (113.54) (0.03) +.000 4.660 (118.36)5.232 (132.89)007 029 008 030 2.344 (59.54) “ 3.75 (95.25) 2.25 (57.15) 1.87

16、0 -.003 (47.50) (0.08) +.000 2.062 (53.37)“ “ 4.00 (101.60)3.570 -.003 (90.68) (0.08) +.000 3.782 (96.06) 4.354 (110.59)009 031 010 032 1.914 (48.62) .004 (0.10) 3.00 (76.20) 1.75 (44.45) 1.510 -.003 (38.35) (0.08) +.000 1.624 (41.25).257 +.005 (6.53) (0.13)-.0003.25 (82.55)3.010 -.003 (76.45) (0.08

17、) +.000 3.124 (79.35) 3.500 (88.90)011 033 012 034 1.620 (41.15) .005 (0.13) 2.75 (69.85) 1.50 (38.10) 1.283 -.003 (32.59) (0.08) +.000 1.395 (35.43)“ “ 2.63 (66.80)2.428 -.003 (61.67) (0.08) +.000 2.540 (64.52) 2.916 (74.07)013 035 014 036 1.414 (35.92) - 2.50 (63.50) 1.25 (31.75) 1.010 -.004 (25.6

18、5) (0.10) +.000 1.122 (28.50)“ “ 2.25 (57.15)2.010 -.004 (51.05) (0.10) +.000 2.122 (53.90) 2.498 (63.45)015 037 016 038 1.273 (32.33) - 2.44 (61.98) 1.13 (28.70) .931 -.002 (23.64) (0.05) +.000 1.045 (26.54)“ “ 1.94 (49.28)1.726 -.002 (43.84) (0.05) +.000 1.840 (46.74) 2.216 (56.29)017 039 018 040

19、1.094 (27.79) - 1.94 (49.28) 1.00 (25.40) .758 -.003 (19.25) (0.08) +.000 .872 (22.15).196 +.004 (4.98) (0.10)-.0001.75 (44.45)1.508 -.003 (38.30) (0.08) +.000 1.622 (41.20) 1.904 (48.36)019 041 020 042 .953 (24.21) - 1.75 (44.45) .88 (22.35) .633 -.003 (16.08) (0.08) +.000 .747 (18.97).169 +.002 (4

20、.29) (0.05)-.0001.50 (38.10)1.258 -.003 (31.95) (0.08) +.000 1.372 (34.85) 1.654 (42.01)021 043 022 044 .828 (21.03) - 1.59 (40.39) .75 (19.05) .506 -.001 (12.86) (0.03) +.000 .624 (15.85).169 +.002 (4.29) (0.05)-.0001.38 (35.05)1.006 -.001 (25.55) (0.03) +.000 1.124 (28.55) 1.406 (35.71)See footnot

21、es at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/52D 4 TABLE I. Dash numbers and dimensions - Continued. Dimensions 2/ Dash No. 3/ Dash No. 4/ V X Y .0040 (0.10) Z Max AA .005 (0.13) BB .02 (0.51)CC .02 (0.51)DD .005 (

22、0.13) EE .003(0.08)FF .02 (0.51) GG Max HH .02 (0.51) JJ KK 001 023 002 024 .012 (0.30) .003 (0.08) 4.202 (106.73) .005 (0.13) .062 (1.57) .50 (12.70).88 (22.35).594 (15.09).143 (3.63).25 (6.35) .05 (1.27) .25 (6.35) .005 (0.13) .005 (0.13) 003 025 004 026 .011 (0.28) ” 3.492 (88.70) “ “ “ “ .531 (1

23、3.49)“ “ “ “ “ “ 005 027 006 028 “ “ 3.082 (78.28) “ “ “ “ “ “ “ “ “ “ “ 007 029 008 030 “ “ 2.634 (66.90) “ “ “ “ “ “ “ “ “ “ “ 009 031 010 032 .007 (0.18) ” 2.000 (50.80) .002 (0.05) .053 (1.35) .38 (9.65).69 (17.53)“ .094 (2.39).31 (7.87) “ .31 (7.87) “ “ 011 033 012 034 “ “ 1.771 (44.98) “ “ “ “

24、 “ “ “ “ “ “ “ 013 035 014 036 “ “ 1.498 (38.05) “ “ “ “ “ “ “ .03 (0.76) “ “ “ 015 037 016 038 “ .002 (0.05) 1.421 (36.09) “ “ “ “ “ “ “ “ “ .004 (0.10) .004 (0.10) 017 039 018 040 .006 (0.15) “ 1.154 (29.31) “ .040 (1.02) .25 (6.35).50 (12.70).438 (11.31).070 (1.78).25 (6.35) “ .25 (6.35) “ “ 019

25、041 020 042 .005 (0.13) “ 1.029 (26.14) “ “ “ “ .406 (10.31)“ “ “ “ “ “ 021 043 022 044 .005 (0.13) “ .906 (23.01) “ “ “ “ .406 (10.31)“ “ “ “ .003 (0.08) .003 (0.08) 1/ PINs 001 through 022 are for flat flanges; PINs 023 through 044 are for grooved flanges. 2/ Metric equivalents are in parentheses.

26、 3/ Copper alloy. 4/ Aluminum alloy. 5/ Each flange mates with an identical PIN. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/52D 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest .01 mm) are given for genera

27、l information only and are based on 1.00 inch = 25.4 mm. 3. One seal is to be supplied with each grooved flange. Inches mm Inches mm .003 0.08 .125 3.18 .005 0.13 .164 4.17 .010 0.25 .190 4.83 .015 0.38 .203 5.16 .030 0.76 .250 6.35 .031 0.79 .3125 7.94 .040 1.02 .625 15.88 .047 1.19 .75 19.05 .062

28、1.57 1.0 25.40 .078 1.98 1.5 38.10 FIGURE 2. Grooved flange seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/52D 6 TABLE II. Gasket dimensions. Style Flange Dimensions 1/ used with M3922/52- A B .010 (0.25) C I 023-024 7.454 .015 (1

29、89.33) (0.38) 4.204 (106.78) .288 - .010 (7.32) (0.25) +.000 I 025-026 6.044 .015 (153.52) (0.38) 3.494 (88.75) “ I 027-028 5.234 .015 (132.94) (0.38) 3.084 (78.33) “ I 029-030 4.336 .015 (110.13) (0.38) 2.636 (66.95) “ II 031-032 3.451 .015 (87.66) (0.38) 1.951 (49.56) .139 .004 (3.53) (0.10) II 03

30、3-034 2.867 .010 (72.82) (0.25) 1.722 (43.74) “ II 035-036 2.449 .010 (62.20) (0.25) 1.449 (36.80) “ II 037-038 2.167 .010 (55.04) (0.25) 1.372 (34.85) “ II 039-040 1.866 .010 (47.40) (0.25) 1.116 (28.35) .103 .003 (2.62) (0.08) II 041-042 1.616 .010 (41.05) (0.25) .991 (25.17) “ II 043-044 1.368 .0

31、10 (34.75) (0.25) .868 (22.05) “ 1/ Metric equivalents are in parentheses. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/52D 7 REQUIREMENTS: Dimensions and configuration: Flange: See figure 1 and table I. Gasket: See figure 2. Material

32、: Flange: Metallic base alloy as specified in table I. Items supplied with flanges: See table III. Marking: See figure 1. Part or Identifying Number (PIN): M3922/52- (and dash number from table I.) AN nomenclature and engineering data: See table IV. Minimum pressure applied shall be 120 Kilopascal (

33、KPa). TABLE III. Items supplied with flange. PIN 1/ M3922/52- Hexagon head cap screw Hexagon nut Spring lockwasher Quantity (each) 001, 002, 023, 024 (5/16) .3125-18 UNC-2A, 1.5 inch long (5/16) .3125-18 UNC-2B .3125 x .078 5 003, 004, 005, 006, 007, 008, 025, 026, 027, 028, 029, 030 (1/4) .250-20 U

34、NC-2A, 1.5 inch long (1/4) .250-20 UNC-2B .250 x .062 5 009, 010, 011, 012, 031, 032, 033, 034 (1/4) .250-20 UNC-2A, 1.0 inch long (1/4) .250-20 UNC-2B .250 x .062 5 013, 014, 015, 016, 035, 036, 037, 038 (1/4) .250-20 UNC-2A, 1.0 inch long (1/4) .250-20 UNC-2B .250 x .062 4 017, 018, 039, 040 (No.

35、10) .190-32 UNF-2A, .750 inch long (No. 10) .190-32 UNF-2B .190 x .047 4 019, 020, 021, 022, 041, 042, 043, 044 (No. 8) .164-32 UNC-2A, .750 inch long (No. 8) .164-32 UNC-2B .164 x .040 4 1/ One gasket (see figure 2) shall be supplied with each PIN 023 through 044. Provided by IHSNot for ResaleNo re

36、production or networking permitted without license from IHS-,-,-MIL-DTL-3922/52D 8 TABLE IV. Cross-reference of PINs/AN nomenclature and engineering data. PIN M3922/52- AN nomenclature Frequency range 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025

37、 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 UG-1714/U UG-1720/U UG-1715/U UG-1717/U UG-1716/U UG-1711/U UG-1712/U UG-1713/U UG-1724/U UG-1725/U UG-1726/U UG-1727/U UG-1728/U UG-1729/U UG-1730/U UG-1731/U UG-1732/U UG-1733/U UG-1734/U UG-1735/U UG-1736/U UG-1737/U UG-

38、1362/U UG-1343/U UG-1718/U UG-1719/U UG-1344/U UG-1345/U UG-1346/U UG-1347/U UG-1348/U UG-1349/U UG-1350/U UG-1351/U UG-1352/U UG-1353/U UG-1354/U UG-1355/U UG-1356/U UG-1357/U UG-1358/U UG-1359/U UG-1360/U UG-1361/U GHz 1.12 - 1.70 1.12 - 1.70 1.45 - 2.20 1.45 - 2.20 1.70 - 2.60 1.70 - 2.60 2.20 -

39、3.30 2.20 - 3.30 2.60 - 3.95 2.60 - 3.95 3.30 - 4.90 3.30 - 4.90 3.95 - 5.85 3.95 - 5.85 4.90 - 7.05 4.90 - 7.05 5.85 - 8.20 5.85 - 8.20 7.05 - 10.0 7.05 - 10.0 8.20 - 12.40 8.20 - 12.40 1.12 - 1.70 1.12 - 1.70 1.45 - 2.20 1.45 - 2.20 1.70 - 2.60 1.70 - 2.60 2.20 - 3.30 2.20 - 3.30 2.60 - 3.95 2.60

40、- 3.95 3.30 - 4.90 3.30 - 4.90 3.95 - 5.85 3.95 - 5.85 4.90 - 7.05 4.90 - 7.05 5.85 - 8.20 5.85 - 8.20 7.05 - 10.0 7.05 - 10.0 8.20 - 12.40 8.20 - 12.40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3922/52D 9 Referenced documents: In addit

41、ion to MIL-DTL-3922, this document references the following: MIL-DTL-24211 ASME B46.1 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever f

42、or any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air

43、 Force - 85 (Project 5985-2009-034) DLA - CC Review activities: Army - AV, MI Navy - AS, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-