DLA MIL-DTL-43176 D-2000 SCREEN LATRINE FIRE WATER WEATHER AND MILDEW RESISTANT TREATED《防火 防水和防霉处理军营防护屏》.pdf

1、I INCH-POUND I MIL-DTL-43176D 15 September, 2000 SUPERSEDING MIL-S-43176C 7 October, 1987 DETAILED SPECIFICATION SCREEN, LATRINE, FIRE, WATER WEATHER AND MILDEW RESISTANT TREATED This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope

2、. This specification covers requirements for a latrine screen made of Camouflage Green 483 polyester duck, that is fire, water, weather and mildew resistant treated. A cover is provided to protect the screen during storage and transportation. 2. APPLICABLE DOCUMENTS “2.1 General. The documents liste

3、d in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, documen

4、t users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. “2.2.1 Specifications, standards, and handbooks The following specifications, standards, and handbooks form a part

5、 of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (reco

6、mmendations, additions, deletions, clarifications) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-CNR, 700 Robbins Ave., Philadelphia, PA 19111-5096 by using the Standardi

7、zation Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 8340 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43176D SPECIFICATIONS FEDERAL A-A-50057 V-T-285 DDD-L-20 MILITARY MIL-P-

8、549 MIL-L-1709 MIL-S- 1734 MIL-P-2383 MIL-DTL-20696 MIL-R-3 0500 MIL-DTL-44 103 - Rope, Fibrous, Tent-Lay - Thread, Polyester - Label: For Clothing, Equipage and Tentage (General Use) - Poles, Tent, Upright and Ridge - Lines, Tent - Slips, Tent Line - Pins, Tent, Wood - Cloth, Coated, Waterproof - R

9、ope, Polyester - Cloth, Duck, Fire Water Illustration and details (Copies of drawings are available from the U. S. Army Biological Chemical Command, ATTN: AMSSB-REO-S(N), NATICK, MA O 1760-50 17.) “2.3 Non-Government publications. The following document(s) form a part of this document to the extent

10、specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitatio

11、n (see 6.2). AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA NASM1649 1 - Grommet, Metallic, General Specification For 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43176D (Applications for copies of referenced documents should be addressed t

12、o the Aerospace Industries Association of America, Inc., 1250 Eye Street, N. W. Washington, DC 20005-3924.) “2.4 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification takes precedence. Nothing in this sp

13、ecification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS “3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 4.2 and 6.2). 3.2 Materials and components. The materials (see 6.

14、5) and components shall be as specified on the applicable drawings and as specified herein. “3.2.1 Cloth. “3.2.1.1 Cloth, duck. The cloth for the screen shall conform to class 1, grade B of MIL-PRF-44 103. “3.2.1.2 Cloth, coated. The cloth for the cover shall conform to type II, class 2, shade Camou

15、flage Green 483 of MIL-PRF-20696. 3.2.2 Thread. The thread shall conform to type I, class 1 subclass A or B, shade S-1 (CA 66022) of V-T-285. The dyed thread shall show colorfastness to weathering equal to or better than the standard shade sample (see 6.3). If no standard shade sample is available t

16、he thread shall show good colorfastness to weathering. Thread size shall be as follows: a. For all stitching except stitching indicated by Yon drawings size F for needle and b. For stitching indicated by “on drawing size F for needle and size E for looper. bobbin. “3.2.3 Lines, tent. The tent lines

17、shall conform to types VI, XV, XVIII and XXI of MIL-L-1709. As an alternate, the following substitute ropes are acceptable for use: % or 5/16 inch diameter rope conforming to A-A-50057. Polyester, Camouflage Green 483 of MIL-R-30500 or three strand, dual fiber polyester/polypropylene (commercial). “

18、3.2.4 Grommets, metallic Grommets shall conform to type III, class 3, size No. 4 of NASM1649 1. 3.2.5 Slips, tent line. Tent line slips shall conform to type II of MIL-S-1734. 3.2.6 Pins, tent, wood. When required, (see 6.2), the tent pins shall be size 1, conforming to MIL-P-2383. 3.2.7 Poles, tent

19、, upright and ridge. When required (see 6.2), the tent poles shall conform to MIL-P-549. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43176D 3.3 Construction. The construction of the latrine screen shall conform to the drawings listed in

20、 2.2.2 and as specified herein. 3.3.1 Stitching machine “3.3.1.1 Types. All stitch types, shall conform to ASTM-D-6193 as follows: a. For all stitching except stitching indicated by Lon drawings -type 301, 5 to b. For stitching indicated by “on drawings - type 401, 5 to 7 stitches per inch. 7 stitch

21、es per inch. Chain portion of stitching shall not appear on outside of screen or cover. 3.3.1.2 Stitching ends. The ends of 301 stitching shall be overstitched not less than 1 inch except where ends are turned under in a hem, held down by other stitching or where stitching is performed automatically

22、. Where 30 1 stitching is performed automatically on stitch patterns such as box, box with cross-stitch, “W stitching or straight line tacking, not less than three tying, overlapping, or back stitches shall be used to secure the ends of stitching. 3.3.1.3 Thread breaks. Thread breaks in stitching sh

23、all be overstitched not less than 1 inch at each break on stitch type 301, and not less than 1 % inches at each break on stitch type 401. Thread breaks noted during inspection shall be repaired by overstitching the existing stitching and the defective area for not less than one inch on type 301 stit

24、ching and 1 % inches on type 401 stitching on each side of the break. The ends of repair stitching are not required to be backstitched. Thread breaks in type 40 1 stitching may be overstitched with stitch type 30 1. “3.3.1.4 Thread lubricant The addition of any lubricant to the polyester sewing thre

25、ad prior to or during the sewing operation is prohibited. 3.3.1.5 Skipped stitches. Two or more consecutively skipped stitches occurring in type 301 stitching shall be overstitched not less than 1 inch on each side of skips. Any skipped stitches in type 401 stitching shall be overstitched not less t

26、han 1-% inches on each side of skip. Skipped stitches in 40 1 stitching may be overstitched with type 30 1 stitching. 3.3.1.6 Automatic stitching Automatic stitching machines may be used to perform any of the required stitch patterns provided the requirements of the stitch pattern, stitches per inch

27、, size and type of thread are met and at least three or more tying, overlapping or backstitches are used to secure the ends of the stitching. “3.4 Repairs. All necessary repairs shall be effected in accordance with Department of The Army Field Manual FM 10-1 6, except that hand-sewn patches, or ceme

28、nted patches other than as specified herein will not be acceptable. Cemented patches on holes, cuts or tears not more than 1 inch in diameter or length, using cement conforming to Minnesota Mining and Manufacturing Co., part # 847 or equal (see 6.6) will be permitted. A maximum of two cemented patch

29、es per section will be allowable without prior contracting officer authorization. All other repairs shall require authorization by the contracting officer. 3.5 Location marks. Marks for showing location of component parts may be done with marking ink or by the use of drill holes. Ink marks or drill

30、holes shall be located such that the marks or holes are completely and permanently covered by the component part. 3.6 Replacement of defective components During the manufacturing process, components having material defects or damages that are classified as defects in 4.4.3 shall be removed from prod

31、uction and replaced with non-defective or properly matched components. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43176D 3.7 Marking. All labels and markings shall conform to DDD-L-20. 3.7.1 Identification marking The letters “US“ on t

32、he screen and cover and the nomenclature on the cover shall conform to type IV, class 9 of DDD-L-20, in the size characters and the locations shown on the drawings. Class 9 markings shall be clearly legible after exposure to accelerated weathering. 3.7.2 Identification labels Identification labels s

33、hall conform to type VI, Class 6 of DDD-L-20 and shall be 3 Yi inches by 5 Yi inches minimum with a blank space of at least 1 % inches provided on the bottom of the label for the Department of Defense Inspector3 stamp. Identification labels shall be stitched to the screen and cover in the locations

34、shown on the drawings. 3.7.3 Erection instruction labels Labels of erection instructions shall conform to type VI, class 7 and shall be stitched to the screen and cover in the locations shown on the drawings. The label shall be a proportionate copy of Drawing 5-4-823 as reproduced from a glossy prin

35、t of the drawing furnished by the contracting officer. The size label shall be, borderline to borderline, 15 inches 2 % inch in the long dimension, with a minimum of Yi inch margin outside of the borderline on all sides. “3.8 Workmanship. The finished latrine screens shall conform to the quality of

36、product established by this document. 4. VERIFICATION 4.1 Responsibility for dimensional requirements Unless otherwise specified in the contract or purchase order, the contractor is responsible for ensuring that all dimensions specified have been met. When dimensions cannot be examined on the end it

37、em, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements. 4.2 Classification of inspections The inspection requirements specified herein are classified as follows: a. b. Conformance inspection (see 4.4).

38、 First article inspection (see 4.3). 4.3 First article inspection When a first article is required (see 6.2) it shall be examined for the defects listed in 4.4.3 and 4.4.4 and tested as specified in 4.4.5. The presence of any defect or failure of any test shall be cause for rejection of the first ar

39、ticle. 4.4 Conformance inspection Sampling for inspection shall be as specified in the contract or purchase order. 4.4.1 Component and material inspection In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherw

40、ise excluded, amended, modified or qualified in this specification or applicable purchase document. 4.4.2 In-process examination. Inspection shall be made to determine that there is no lubrication of the polyester thread prior to or during the sewing operations as specified in 3.3.1.4. 5 Provided by

41、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-43176D “4.4.3 End item visual examination The end item shall be examined for the defects listed in Table I. The lot size shall be expressed in units of latrine screens or covers. The sample unit shall be o

42、ne latrine screen or cover. The inspection level shall be I. TABLE I. End item visual defects Classification Examine Defect Major Minor Cloth A B Cut, or tear longer than 1/8 inch; hole (including exposed drill hole) larger than 1/8 inch diameter: - on screen - on cover Exposed drill hole (U8 inch o

43、r less) i.e., not Covered by attached parts: - more than one but not more than four - more than four Broken or missing yarn; multiple floats clearly visible at normal inspection distance (approximately 3 feet) Rope compo- Any cut; any break nents - on guy line - on tie line Eye splice omitted Eye sp

44、lice not as specified Free ends not fiiished as specified Hardware Broken 101 102 Malformed: - fails to perform intended function - but will perform intended function Corroded area Burr or sharp edge which may cause injury in handling or damage to fabric 103 Poles i.e., grommets or washers 104 aroun

45、d hole 105 become disengaged 106 Seams & stitching Open seam on stitch type 301: - for more than % inch but not more than linch - for more than 1 inch 20 1 301 3 02 202 203 204 303 205 3 04 305 206 306 307 308 309 207 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

46、ense from IHS-,-,-MIL-DTL-43176D TABLE I. End item visual defects (continued) Classification Examine Defect Major Minor A B Open seam on stitch type 401: - one row of stitching open for 1 - one row of stitching open for more - both rows of stitching open (not inch or less 310 than 1 inch 208 necessa

47、rily at the same location) 107 Note: A seam shall be classified as open when one or more stitches joining a seam are broken, or when one or more skipped or run-off stitches occur. On double stitched seams, a seam shall be classified as open when either one or both sides of a seam are open. Raw edges

48、 caught in stitching: - more than 1 inch but not more than - more than 3 inches 3 inches Thread breaks: - overstitched less than 1 Yi inches on - overstitched less than 1 inch on stitch type 401 stitch type 301 Note: Thread breaks not overstitched shall be classified as open seams. - overstitched le

49、ss than 1 Yi inches on - overstitched less than 1 inch on stitch Skipped stitches: stitch type 401 type 301 Note: Skipped stitches not overstitched shall be classified as open seams. Needle chews resulting in cut or tear larger than 1/8 inch in length, or hole larger than 1/8 inch in diameter: - on screen - on cover 311 209 3 12 210 21 1 212 213 313 One or more required rows of stitching omitted 108 7 Provided by IHSNot for ResaleNo reproduction or networking p