DLA MIL-DTL-52525 43-2008 FITTINGS HOSE CRIMP TYPE SPLIT-FLANGE STRAIGHT.pdf

1、 INCH-POUNDMIL-DTL-52525/43 1 December 2008 DETAIL SPECIFICATION SHEET FITTINGS, HOSE, CRIMP TYPE, SPLIT-FLANGE, STRAIGHT This specification is approved for use by all Department and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of t

2、his specification sheet and MIL-DTL-52525. Hose Flange size Part or Identifying Number (PIN) ID ref inches (mm) Dash no. inches (mm) Dash no. A max inch (mm) M52525/43-16-16 1.000 (25.40) -16 1.000 (25.40) -16 1.75 (44.45) M52525/43-20-20 1.250 (31.75) -20 1.250 (31.75) -20 2.00 (50.80) M52525/43-24

3、-24 1.500 (38.10) -24 1.500 (38.10) -24 2.40 (60.96) M52525/43-32-32 2.000 (50.80) -32 2.000 (50.80) -32 2.80 (71.12) PIN B min inches (mm) C max inches (mm) M52525/43-16-16 .75 (19.05) 5.06 (128.52) M52525/43-20-20 1.00 (25.40) 5.55 (140.97) M52525/43-24-24 1.25 (31.75) 6.13 (155.70) M52525/23-32-3

4、2 1.68 (42.67) 6.91 (175.51) FIGURE 1. Fitting, clamp-on to 4-bolt split-flange, straight. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525/43 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for in

5、formation only. 3. All dimensions not shown shall be in accordance with SAE-J516 and SAE-J518 as applicable. FIGURE 1. Fitting, clamp-on to 4-bolt split-flange, straight - Continued. ENGINEERING DATA: SAE-J517, type 100R10 hoses have been discontinued by SAE. Suggested SAE-J517 replacement hoses are

6、 specified in table I. The “RE” designator at the end of the hose type “100RE” is a MIL-DTL-52471 term used to indicate a hose type that has been discontinued and to use an SAE-J517 replacement hose see MIL-DTL-52471/3. The hose assembly document MIL-DTL-52471/3 is being retained so replacement part

7、s can be ordered from this slash sheet. The intent is to allow users the ability to use PINs in MIL-DTL-52471/3 to order hose assemblies. Manufacturers will use the appropriate substitute hose and fittings to make a hose assembly to meet the mating requirements of the fittings listed in this slash s

8、heet, and shall meet the performance requirements of SAE-J517, and mark it in accordance with MIL-DTL-52471/3. TABLE I. Hose type 100R10 to SAE replacement. 1/ 100R10 hose dash size SAE-J517 replacement PIN Operating pressure psi SAE MPa 100RE MPa -16 SAE J517 100R13-16 4000 35 27.6 -20 SAE J517 100

9、R12-20 3000 21 20.7 -24 SAE J517 100R12-24 2500 17.5 17.2 -32 SAE J517 100R12-32 2500 17.5 17.2 1/ If the SAE-J517 hose in table I does not meet system requirements chose an SAE-J517 hose with pressure requirements at or above pressure requirements specified in this specification. REQUIREMENTS: Fitt

10、ings shall be in accordance with figure 1 and in tables II and III. The fittings described herein are for use with hose in accordance with MIL-DTL-52471/7 and hose assemblies in accordance with MIL-DTL-52471/3, type 100R10, 4-spiral-wrap hose. If fittings are to be used on an oxygen hose, see MIL-DT

11、L-52525. Materials and finishes shall be in accordance with MIL-DTL-52525 and in table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525/43 3 TABLE II. Material and finish identification codes. 1/ 2/ PIN code material/plating finish M

12、aterial Plating finish A Anodize in accordance with MIL-A-8625, type II. AN Anodize in accordance with MIL-A-8625, type II and NAVAIR trivalent chromium pretreatment (TCP) in accordance with MIL-DTL-81706, type 2, class A. BN Aluminum alloy 6061 or 7075 Bare aluminum with NAVAIR TCP in accordance wi

13、th MIL-DTL-81706, type 2, class A. C Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. CN Steel Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2 and NAVAIR TCP in accordance with MIL-D

14、TL-81706, type 2, class A. YC Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. YN Chrome-molybdenum steel alloy 4130 Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2 and NAVAIR TCP in

15、 accordance with MIL-DTL-81706, type 2, class A. F Steel FN Chrome-molybdenum steel alloy 4130 NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. G Steel YG Chrome-molybdenum steel alloy 4130 Zinc plating with colorless passivate in accordance with ASTM B633, type V, Fe/Zn 25. H Steel YH

16、Chrome-molybdenum steel alloy 4130 Zinc phosphate finish in accordance MIL-DTL-16232, type Z, class1. 3/ J Steel YJ Chrome-molybdenum steel alloy 4130 Zinc plating with chromate conversion in accordance with ASTM B633; type II or III, Fe/Zn 5, or ASTM B695, type II, class 5. K Nickel-copper alloy UN

17、S N04400 No additional finish. M High-chromium nickel alloy UNS N06690 No additional finish. N Steel YN Chrome-molybdenum steel alloy 4130 Zinc aluminum in accordance with ASTM F1136, grade 3, NC. P Steel YP Chrome-molybdenum steel alloy 4130 Zinc plating with colorless passivate in accordance with

18、ASTM B633, type VI, Fe/Zn 5. S No additional finish. Passivation in accordance with SAE-AMS2700, type 6 or 7. SN Corrosion resistant steel Passivation above and NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. T Titanium Anodize in accordance with SAE-AMS2488, type 2. V Steel Zinc-nicke

19、l in accordance with SAE-AMS2417, type 1. W Steel YW Chrome-molybdenum steel alloy 4130 Any zinc plating above. Z Steel YZ Chrome-molybdenum steel alloy 4130 Any zinc plating above with NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. 1/ All materials and finishes shall be in accordance

20、 with MIL-DTL-52525. 2/ Embitterment test need not be run. 3/ Zinc phosphate finish is hexavalent chromium free. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525/43 4 The operating pressure shall be specified in table III. Maximum operat

21、ing pressures are for low carbon steel fittings consult manufacturer for values on other materials. TABLE III. Maximum operating pressures of fittings. 1/ 2/ 100R10 hose dash size Hose ID inches (mm) psi MPa -16 1.000 (25.40) 4000 27.6 -20 1.250 (31.75) 3000 20.7 -24 1.500 (38.10) 2500 17.2 -32 2.00

22、0 (50.80) 2500 17.2 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. PIN: The PIN consists of the letter “M” the specification sheet number, a dash, a number for the connecting unit, and a material finish designator. M 52525/43 -16 -16 A PIN example: M52525/43-16-16

23、A, describes a straight crimp type split flange for a 1.000 inch (25.40 mm) hose, and with a 1.000 inch (25.40 mm) flange, aluminum with an anodized finish. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only when the other materia

24、ls and finishes specified in this document cannot meet performance requirements. Color identification. Color identification shall be in accordance with SAE-AS4841. Marking shall include the manufacturers name or trademark, size, and hose identifier RE. Location of marking is optional. Harmonization

25、to SAE-J516 cross reference PIN in table IV is for reference only. SAE style fittings may not have the same material/finish as required by MIL-DTL-52525 and legacy with MIL-DTL-52471. Size dash number for flange (see figure 1) Specification sheet numberSize dash number for hose (see figure 1) M pref

26、ix Material/finish designator (see table II) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525/43 5 TABLE IV. Harmonization to SAE-J516 cross reference PIN. 1/ Replacement PIN Superseded PIN SAE J516 Equivalent PIN 2/ SAE J518-2 PIN Flang

27、e head only M52525/43-16-16 M52525/23-16-16 SAE J516 16-16 490154EE SAE J518/2-16-0562 M52525/43-20-20 M52525/23-20-20 SAE J516 20-20 490154EE SAE J518/2-20-0562 M52525/43-24-24 M52525/23-24-24 SAE J516 24-24 490154EE SAE J518/2-24-0562 M52525/43-32-32 M52525/23-32-32 SAE J516 32-32 490154EE SAE J51

28、8/2-32-0562 1/ Material and finish designators are omitted from PINs, reference table I and SAE-J846. 2/ The “EE” at the end of the SAE PIN is to indicate a nonstandard part. Referenced documents. In addition to MIL-DTL-52525, this document references the following: MIL-A-8625 MIL-DTL-16232 MIL-DTL-

29、52471 MIL-DTL-52471/3 MIL-DTL-52471/7 MIL-DTL-52525/16 MIL-DTL-52525/17 MIL-DTL-81706 ASTM B633 ASTM B695 ASTM F1136 SAE-AMS-C-81562 SAE-AMS-QQ-P-416 SAE-AMS2417 SAE-AMS2488 SAE-AMS2700 SAE-AS4841 SAE-J516 SAE-J517 SAE-J518 SAE-J846 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA -

30、 CC Air Force - 99 DLA - CC (Project 4730-2007-099) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-