DLA MIL-DTL-5423 15 H-2009 BOOT DUST AND WATER SEAL TYPE B (FOR TOGGLE AND PUSHBUTTON SWITCHES CIRCUIT BREAKERS AND ROTARY-ACTUATED PARTS) (FOR HANDSET SWITCHES) STYLE 5.pdf

1、INCH-POUND MIL-DTL-5423/15H 17 February 2009 SUPERSEDING MIL-DTL-5423/15G 4 February 2008 DETAIL SPECIFICATION SHEET BOOT, DUST AND WATER SEAL, TYPE B (FOR TOGGLE AND PUSHBUTTON SWITCHES, CIRCUIT BREAKERS, AND ROTARY-ACTUATED PARTS) (FOR HANDSET SWITCHES), STYLE 5 This specification sheet is approve

2、d for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5423. FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5930 Provided by IHSNot for ResaleNo reproduction or ne

3、tworking permitted without license from IHS-,-,-MIL-DTL-5423/15H 2 FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIGURE 1. Dimensions and configuration Continued. MIL-DTL-5423/15H 3 Provided by IHSN

4、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/15H 4 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm .015 0.38 .087 2.21 .210 5.33 .362 9.19 .652 16.56 1.625 41.28 .025 0.64 .093 2.36 .219 5.56 .375 9.53 .688 17.48 1.765 44.83 .031 0.79 .10

5、9 2.77 .271 6.88 .406 10.31 .700 17.78 1.833 46.56 .040 1.02 .117 2.97 .312 7.92 .420 10.67 .719 18.26 1.953 49.61 .045 1.14 .125 3.18 .313 7.95 .449 11.40 .809 20.55 2.148 54.56 .046 1.17 .140 3.56 .340 8.64 .473 12.01 .810 20.57 2.419 61.44 .047 1.19 .141 3.58 .343 8.71 .500 12.70 .813 20.65 2.594

6、 65.89 .050 1.27 .175 4.45 .344 8.74 .562 14.27 1.250 31.75 2.828 71.83 .062 1.57 .203 5.16 .350 8.89 .612 15.54 1.443 36.65 3.118 79.20 .070 1.78 .205 5.21 .359 9.12 .625 15.88 1.500 38.10 3.380 85.85 .078 1.98 3.661 92.99 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general

7、 information only. 2. Unless otherwise specified, tolerances are .015 (0.38 mm). 3. All corner and fillet radii to be .016 (0.41 mm) unless otherwise specified. 4. Flash at parting line must not extend out more than .005 (0.13 mm) or exceed .020 (0.51 mm) in thickness FIGURE 1. Dimensions and config

8、uration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/15H 5 REQUIREMENTS Dimensions and configuration: See figure 1. Silicon rubber: Grade 50 per A-A-59588. Watertightness: MIL-STD-108, table I. Endurance: 500,000 operations

9、, see MIL-DTL-5423. Minute cracks after life test, which do not permit leakage, shall not be cause for rejection. Color: See table I. Part or Identifying Number (PIN): See figure 1 or table I. TABLE I. Colors. Part Number Color Former part number identification M5423/15-01 Gray SM-C-96099 SM-C-10536

10、9 M5423/15-02 Black SM-C-544237 M5423/15-03 Black SM-C-627674 Qualification: First Article Testing in accordance with MIL-DTL-5423. The margins of this specification are marked with vertical lines to indicate where modifications were made. This was done as a convenience only and the Government assum

11、es no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Reference Documents: MIL-DTL-5423 MIL-STD-108 A-A-59588 Custodians: Preparing ac

12、tivity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5930-2008-071) DLA CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-