DLA MIL-DTL-55181 3 D-2008 CONNECTOR PLUG ELECTRICAL WATERPROOF 4 PIN CONTACTS SOLDER TURRET 35 AMP《35安培焊钳4个针式触点防水电气插头连接器》.pdf

1、 MIL-DTL-55181/3D INCH-POUND10 March 2008 SUPERSEDING MIL-C-55181/3C 23 June 1986 DETAIL SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL, WATERPROOF, 4 PIN CONTACTS, SOLDER TURRET, 35 AMP This specification is approved for use by all Departments and Agencies of the Department of Defense. The require

2、ments for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55181. CONNECTOR ASSEMBLY FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55181/3

3、D 2 CONTACT FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55181/3D 3 Inches mm Inches mm Inches mm Inches mm .028 .038 .040 .041 .042 .044 .047 .048 .052 .076 .078 .080 0.71 0.96 1.01 1.04

4、 1.06 1.12 1.19 1.22 1.32 1.93 1.98 2.03 .082 .084 .086 .089 .092 .094 .095 .099 .110 .125 .176 .233 2.08 2.13 2.18 2.26 2.34 2.39 2.41 2.51 2.79 3.17 4.47 5.92 .235 .250 .275 .298 .303 .313 .344 .375 .406 .466 .470 .513 5.97 6.35 6.99 7.57 7.70 7.95 8.74 9.52 10.31 11.83 11.94 13.03 .519 .625 .925

5、.995 1.000 1.095 1.103 1.470 1.585 2.125 2.500 13.18 15.87 23.49 25.27 25.40 27.81 28.01 37.34 40.26 53.97 63.50 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances are .005 (0.13 mm) inch for three place decimals and .01

6、 (0.3 mm) inch for two place decimals. 4. Angular tolerances shall be 30 minutes unless otherwise specified. 5. See table l for cable size accommodations. FIGURE 1. Dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: See figure 1 and table I. Contacts: 35 ampere co

7、ntact rating, 12 AWG. Part or Identifying Number (PIN): The PIN shall consist of M55181/3 - (dash number as specified in table I). TABLE I. Dash numbers, cross reference and mating connector table. Cable size accommodation Mating connector PIN Type designator 1/MIN MAX PIN Type designator 1/M55181/3

8、-01 MW10M(M)A11 .292 (7.42) .343 (8.71) M55181/4-01 MW20F(M)A00 M55181/3-02 MW10M(M)A13 .323 (8.20) .406 (10.31) M55181/4-01 MW20F(M)A00 M55181/3-03 MW10M(M)A17 .448 (11.38) .531 (13.48) M55181/4-01 MW20F(M)A00 M55181/3-04 MW10M(M)A19 .511 (12.98) .593 (15.06) M55181/4-01 MW20F(M)A00 M55181/3-05 MW1

9、0M(M)A15 .386 (9.80) .468 (11.88) M55181/4-01 MW20F(M)A00 1/ This type designator shall not be referenced for procurement purposes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55181/3D 4 Changes from previous issue. The margins of this sp

10、ecification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements o

11、f this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 11 DLA - CC (Project 5935-2007-123) Review activity: Air Force - 99 NOTE: The a

12、ctivities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-