DLA MIL-DTL-55302 84 C (1)-2011 CONNECTORS PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES CONTACTS CRIMP DIP SOLDER TAIL SOLDER TURRET AND WIREWRAP.pdf

1、AMSC N/A FSC 5935 MIL-DTL-55302/84C w/AMENDMENT 1 14 March 2011 SUPERSEDING MIL-DTL-55302/84C 15 November 2004 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: CONTACTS CRIMP, DIP SOLDER TAIL, SOLDER TURRET, AND WIREWRAP This specification is approved for use by al

2、l Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. FIGURE 1. Contact termination. INCH-POUND Inactive for new design after 1 July 1989. Provided by IHSNot for ResaleNo repro

3、duction or networking permitted without license from IHS-,-,-MIL-DTL-55302/84C w/AMENDMENT 1 2 FIGURE 1. Contact termination Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/84C w/AMENDMENT 1 3 Inches mm Inches mm Inches mm .0

4、01 0.03 .074 1.88 .382 9.70 .002 0.05 .080 2.03 .420 10.67 .003 0.08 .100 2.54 .624 15.85 .020 0.51 .116 2.95 .638 16.21 .021 0.53 .118 3.00 .690 17.53 .025 0.64 .156 3.96 .855 21.72 .036 0.91 .158 4.01 .82 20.8 .048 1.22 .170 4.32 .880 22.35 .052 1.32 .250 6.35 .895 22.73 .058 1.47 .262 6.65 1.135

5、28.83 .062 1.57 .350 8.89 1.172 29.77 .071 1.80 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals, .02 (0.5 mm) for two place decimals, and 2 on angles. 4. These conn

6、ectors mate with connectors in accordance with MIL-DTL-55302/82. 5. Dimensions shall be .025 nominal, .022 minimum. 6. Minimum point of .210 (5.33 mm) at which gauge having the minimum diameter of the mating pin and a square face encase socket contact spring. 7. Minimum point of .304 (7.72 mm) at wh

7、ich gauge having the minimum diameter of the mating pin and a square face encase socket contact spring. FIGURE 1. Contact termination Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/84C w/AMENDMENT 1 4 REQUIREMENTS Dimensions

8、 and configuration: See figure 1. Material: Crimp, removable: 01 - Phosphor bronze in accordance with ASTM B134/B134M. 02 - Beryllium copper in accordance with ASTM B196/B196M. Dip solder tail: 03 Solder eyelet: 04 - Phosphor bronze in accordance with ASTM B134/B134M. Wrappost: 05 06 Contact sleeve:

9、 Stainless steel in accordance with ASTM A240/A240M. All contact sleeves are passivated except -01 which has a gold flash. Plating: Contact finish in accordance with ASTM B488, type 2, code C, class 1.27, over copper plate. Qualification and quality conformance requirements are not applicable. All c

10、ontacts are tested in accordance with the applicable specification sheet. All contacts are supplied with MIL-DTL-55302/82 and cannot be acquired separately. Part or Identifying Number (PIN): M55302/84-(dash number from figure I). Amendment notations. The margins of this specification are marked with

11、 vertical lines to indicate where modifications from this amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on

12、the entire content irrespective of the marginal notations. Reference documents. In addition to MIL-DTL-55302, this document references the following: MIL-DTL-55302/82 ASTM A240/A240M ASTM B134/B134M ASTM B196/B196M ASTM B488 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC

13、 DLA CC (Project 5935-2010-116) Review activities: Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-