DLA MIL-DTL-641 16 D-2013 JACKS TELEPHONE TYPES JJ-104 JJ-105 AND JJ-107.pdf

1、AMSC N/A FSC 5935 MIL-DTL-641/16D 15 November 2013 SUPERSEDING MIL-J-641/16C 25 July 1966 DETAIL SPECIFICATION SHEET JACKS, TELEPHONE TYPES JJ-104, JJ-105 AND JJ-107 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring th

2、e product described herein shall consist of this specification sheet and MIL-DTL-641. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Jacks may be multiple mounted on a panel in accordance with the minimum center to center dimensions specified in table I.

3、 4. The schematic shows required switching operations but does not indicate a required mechanical arrangement of the parts. FIGURE 1. Dimensions and configuration. Inches mm Inches mm Inches mm .002 0.05 .094 2.39 0.625 15.88 .005 0.13 .125 3.18 .875 22.23 .015 0.38 .156 3.96 1.015 25.78 .016 .41 .2

4、515 6.39 1.125 28.58 .020 .51 0.375 9.53 1.250 31.75 .031 .79 0.500 12.70 1.375 34.93 .062 1.57 .562 14.27 2.797 71.04 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/16D 2 TABLE I. Dimensions. REQUIREMENTS: Dimensions and conf

5、iguration: See figure 1 and table I. Insertion and withdraw forces shall be as follows. Insertion force - 7 pounds (maximum). Withdraw force - 1.5 pounds (minimum). - 7 pounds (maximum). Spring life test is applicable. Test plug TP55, in accordance with MIL-DTL-641, shall be used. The Part or Identi

6、fying Number (PIN) consists of the letter M, the basic specification number, the specification sheet number, and a number for jack type. (see table II) M 641 /16 - 1 Type designation Specification sheet number Specification number M prefix PIN example: M641/16-1 indicates type JJ-104 telephone jack.

7、 TABLE II. PIN. Dash number Type designation Connection Mounting Switching action upon insertion of plug 1/ 1 JJ-104 Tip and sleeve Single lug or bushing One break make, one break 2 JJ-105 One break make 3 JJ-107 One break 1/ The hyphen indicates sequence. Marginal notations are not used in this rev

8、ision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. This document references MIL-DTL-641. Center to center dimensions for multiple mounting panel Type A max In direction of pileup (min) At right angle to pileup (min) JJ-104 1.250 1.375

9、 .688 JJ-105 1.000 1.250 JJ-107 .875 1.250 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/16D 3 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA - CC Navy EC Air Force 85 (Project 5935-2013-041) DLA - CC Review activities:

10、 Army AR, AT, CR4, MI Navy AS, MC, OS, SH Air Force 11, 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-