DLA MIL-DTL-641 19 F-2013 JACKS (BANTAM) TELEPHONE 3 CONDUCTOR SINGLE.pdf

1、AMSC N/A FSC 5935 MIL-DTL-641/19F 15 November 2013 SUPERSEDING MIL-J-641/19E 12 November 1993 DETAIL SPECIFICATION SHEET JACKS, (BANTAM) TELEPHONE, 3 CONDUCTOR, SINGLE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring

2、the product described herein shall consist of this specification sheet and MIL-DTL-641. Dash numbers -1, -2, -5 and -6 (no breaks) FIGURE 1. Dimensions and configurations. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/19F 2 D

3、ash numbers -3, -4, -7 and -8 (2 breaks) Dash numbers -9, -10, -11 and -12 (2 breaks, 1 make) FIGURE 1. Dimensions and configurations Continued. Inches mm Inches mm Inches mm .002 0.05 .0625 1.588 .375 9.53 .010 0.25 .153 3.89 .578 14.68 .015 0.38 .175 4.44 .600 15.24 .020 0.51 .250 6.35 .650 16.50

4、.030 0.76 .279 7.09 .780 19.81 .035 0.89 .281 7.14 2.250 57.15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/19F 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All dimensions are after pla

5、ting. 4. All undimensioned pictorial features are for reference purposes only. FIGURE 1. Dimensions and configurations Continued. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All dimensions are after plating. 4. Finger shall be hardened to Rockwell C 6

6、0-62, polished, and then hard-chromium plated to .0003 inch (0.008 mm) maximum thickness. 5. Concentricity shall be .003 (0.08 mm) total indicator reading. FIGURE 2. Test plug TP-777. Inches mm Inches mm Inches mm .001 0.03 .065 1.65 .290 7.4 .002 0.05 .100 2.54 .506 12.85 .003 0.08 .125 3.18 .622 1

7、5.80 .005 0.13 .143 3.63 .860 21.84 .010 0.25 .150 3.81 2.250 57.15 .045 1.14 .174 4.42 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/19F 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All

8、 dimensions are after plating. 4. Solder lug terminals (not shown) shall meet the requirements of MIL-DTL-641, 3.5.5, and the “A” dimensions of figure 1 shall be .325 inch (8.26mm) maximum. FIGURE 3. Terminals. Inches mm Inches mm .002 0.05 .100 2.54 .010 0.25 .220 5.60 .035 0.89 .795 20.19 .061 1.5

9、5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/19F 5 REQUIREMENTS: Dimensions and configuration: See figure 1. Terminals. See figure 3 (wirewrap) or MIL-DTL-641 (solder lug). Materials. Springs: Nickel silver. Contact: Palladium or gol

10、d alloy. Insertion and withdraw forces shall be as follows. Insertion force - 7 pounds (maximum). Withdraw force - 1 pound (minimum). - 7 pounds (maximum). Test plug - TP777 (see figure 2). Spring life test is applicable. Test plug TP777, shall be used. Frame strength test is applicable. Load 7 poun

11、ds maximum. Terminal of tip contact spring shall be on the right side when terminals are viewed from the rear, with the jack in a position such that the contact spring pileup is on top of the jack frame. Cutout in the jack frame shall be positioned so that a minimum of .016 inch (.4mm) clearance exi

12、sts between the tip of the TP-777 plug and the edge of the frame cutout at all times during insertion of the plug. All terminals shall be stacked as shown on schematic. (see figure 1) Mating plugs. See table II. Supersession data. See table III. The Part or Identifying Number (PIN) consists of the l

13、etter M, the basic specification number, the specification sheet number, and a number for jack type. (see table I) M 641 /19 - 1 Type designation Specification sheet number Specification number M prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

14、-MIL-DTL-641/19F 6 TABLE I. PIN. Part number Connection Mounting Switching action Terminal Dimension B 1 Tip, ring and sleeve Single lug None Wirewrap .115 diameter 2 None Solder lug 3 2 breaks Wirewrap 4 2 breaks Solder lug 5 None Wirewrap .099-48UNC-2B 6 None Solder lug 7 2 breaks Wirewrap 8 2 bre

15、aks Solder lug 9 2 breaks, one make Wirewrap .115 diameter 10 2 breaks, one make Solder lug 11 2 breaks, one make Wirewrap .099-48UNC-2B 12 2 breaks, one make Solder lug 1/ The hyphen indicates sequence. TABLE II. Mating plugs. Dash number Mating plug -1 M642/13-1, -2 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11

16、 -12 TABLE III. Supersession data. PIN M641/19 Manufacturers PIN Manufacturers cage -5 WTT-32BFM 82389 -6 TT-32BFM 82389 -7 WTT-34BFM 82389 -8 TT-34BFM 82389 -9 PJ-805W 70674 -10 PJ-805 70674 Marginal notations are not used in this revision to identify changes with respect to the previous issue due

17、to the extent of the changes. Referenced documents. This document references MIL-DTL-641. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-641/19F 7 CONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA - CC Navy EC Air Force 85 (Pro

18、ject 5935-2013-042) DLA - CC Review activities: Army AR, AT, CR4, MI Navy AS, MC, OS, SH Air Force 11, 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-