DLA MIL-DTL-83513 10 D-2008 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL RIGHT ANGLE PIN CONTACTS 2 ROW SOLDER TYPE NARROW PROFILE 9 THROUGH 37 CONTACTS PR.pdf

1、INCH-POUND MIL-DTL-83513/10D 29 October 2008 SUPERSEDING MIL-DTL-83513/10C 20 September 2002 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, MICROMINIATURE, POLARIZED SHELL, RIGHT ANGLE, PIN CONTACTS, 2 ROW, SOLDER TYPE, NARROW PROFILE, 9 THROUGH 37 CONTACTS, PRINTED CIRCUIT BO

2、ARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. FIGURE 1. Connector, plug, .050 spacing. AMSC N/A FSC 5935 Provided by IHS

3、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 2 Inches mm Inches mm .002 0.05 .109 2.77 .003 0.08 .140 3.56 .0038 0.097 .1848 4.694 .010 0.25 .185 4.70 .015 0.38 .186 4.72 .036 0.91 .190 4.83 .050 1.27 .250 6.35 .0669 1.699 .325 8.26 .096 2.44 F

4、IGURE 1. Connector, plug, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 3 Number of contacts A Max B .005 D E Max F Max G .01 H Max 9 .787 (19.99) .565 (14.35) .3338 (8.48) .425 (10.80) .425 (10.80) .230

5、(5.84) .787 (19.99) 15 .937 (23.80) .715 (18.16) .4838 (12.29) .425 (10.80) .425 (10.80) .130 (3.30) .937 (23.80) 21 1.087 (27.61) .865 (21.97) .6338 (16.10) .425 (10.80) .425 (10.80) .130 (3.30) 1.087 (27.61) 25 1.187 (30.15) .965 (24.51) .7338 (18.64) .425 (10.80) .425 (10.80) .130 (3.30) 1.187 (3

6、0.15) 31 1.337 (33.96) 1.115 (28.32) .8838 (22.45) .450 (11.43) .525 (13.34) .130 (3.30) 1.090 (27.69) 37 1.487 (37.77) 1.265 (32.13) 1.0338 (26.26) .450 (11.43) .525 (13.34) .130 (3.30) 1.190 (30.23) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless

7、 otherwise specified, tolerances are .005 (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accor

8、dance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpo

9、st (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, wh

10、ere as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-

11、30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3

12、 percent lead. 9. Termination lengths available: .109 (2.77 mm), .140 (3.56 mm) or .172 (4.37 mm). The tolerance shall be .015 (0.381 mm) for all termination lengths. 10. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series sta

13、inless steel, passivated in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector, plug, .050 spacing. Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 4 NOTE: Engaging face of pin insert shown, cavity identification n

14、umbers are for reference only and do not appear on the part. FIGURE 2. Insert arrangement, termination view - right angle - narrow profile. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 5 FIGURE 3. Layout arrangement. Provided by

15、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 6 es mm Inch mm Inches.020 0.51 .158 4.01 .040 1.02 .565 14.35 .050 1.27 .715 18.16 .083 2.11 .865 21.97 .096 2.44 .965 24.51 .100 2.54 1.115 28.32 .108 2.74 1.265 32.13 NO3. Unless otherwise spec

16、ified, tolerances are .005 (0.13 mm). FIGURE 3. Layout arrangementTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 7 REQUIREMENTS: i

17、mensions and configurations: See figures 1, 2 and 3. urrent rating, maximum: 3 amperes per contact. Materials: tting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. hell: The requirements for shell materials shall be in accordance with MIL-DTL-83513.

18、th ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 84M and ASTM A582/A582M, 300 series tainless steel, passivated in accordance with SAE-AMS-2700, type2. onform to A-A-59551, no. 24 AWG copper, except shall be tin-ad plated with a minimum of 3 percent l

19、ead. ating connector: Shall conform to MIL-DTL-83513/2 and MIL-DTL-83513/4. der dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 accordance with J-STD-006. the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column.

20、M83513/10-DCTermination organization area: PoSPlastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance wiASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with Jackpost: Corrosion resistant steel in accordance

21、 with ASTM A484/A4sWire termination pins: Wire termination pins shall cleMPlating of termination leads: SolinPart or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter fromD 01 A P sheet number (see figure 2) Te n length (interface crit

22、ical) Hardware A = rodeposited threaded insert 03 = 172 = jackpost and threaded insert N =F = 7 SteelT = Nickel fluorocarbon polymer ument based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Specification Insert arrangements rminatio Shell

23、finish A = 09 B = 15 01 = .109 02 = .140 Pure electaluminum N = No hardware or P = jackpost attach C = 21 . C = Cadmium T = threaded insert D = 25 K = Zinc nickel WE = 31 electroless nickel 3 (space applications only) P = Passivated Stainless Changes from previous issue: The margins of this specific

24、ation are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this doc

25、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/10D 8 Reference documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/2 ASTM A484/A484M A-A-59551 MIL-DTL-83513/4 ASTM A582/A582M J-STD-006 MIL-M-2

26、4519 ASTM D4067 SAE-AMS-2700 AST D5138 ASTM D5927 AST D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-058) NASA - NA DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed abo

27、ve were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-