DLA MIL-DTL-83513 15 E-2009 CONNECTORS ELECTRICAL RECTANGULAR RECEPTACLE MICROMINIATURE POLARIZED SHELL RIGHT ANGLE SOCKETS CONTACTS 4 ROW SOLDER TYPE NARROW PROFILE 100 CONTACTS P.pdf

1、 INCH-POUND MIL-DTL-83513/15E 6 March 2009 SUPERSEDING MIL-DTL-83513/15D 14 July 2004 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, MICROMINIATURE, POLARIZED SHELL, RIGHT ANGLE, SOCKETS CONTACTS, 4 ROW, SOLDER TYPE, NARROW PROFILE, 100 CONTACTS, PRINTED CIRCUIT BOARD Th

2、is specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm .003 0.80 .025 0.64

3、.130 3.30 .200 5.08 .590 14.99 1.825 46.36 .005 0.13 .050 1.27 .144 3.66 .2712 6.888 1.010 25.65 2.175 55.25 .010 0.25 .109 2.77 .175 4.45 .400 10.16 1.3842 35.159 .015 0.38 .125 3.18 .185 4.70 .420 10.67 1.800 45.72 FIGURE 1. Connector, receptacle, .050 spacing. AMSC N/A FSC 5935 Provided by IHSNot

4、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/15E 2NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. Termination organization area to be optionally

5、 molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance

6、 with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M an

7、d ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for

8、 #2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-245

9、19 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519 8. Wire termination sockets shall conform to A-A-59551, no. 24 AWG copper. 9. Interfacial seals are included with each type receptacle connector, except shall be tin-lead plated with a minimum of 3 percent lead. 10. Termination l

10、engths available: .109 (2.77 mm), .140 (3.56 mm), or .172 (4.37 mm). The tolerance shall be .015 (0.38 mm) for all termination lengths. 11. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in acc

11、ordance with SAE-AMS-2700, type 2. FIGURE 1. Connector, receptacle, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/15E 3NOTE: Engaging face of socket insert shown, cavity identification numbers are for referen

12、ce only and do not appear on the part. FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/15E 4FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

13、 from IHS-,-,-MIL-DTL-83513/15E 5REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. She

14、ll: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D40

15、67 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Wire termination pins: Wire termination p

16、ins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall conform to MIL-DTL-83513/1 and MIL-DTL-83513/3. Plating of termination leads: Solder dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB3

17、7 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/15- H 01 A P Spe

18、cification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware H = 100 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach 03 = .172 C = Cadmium U = 4-40 threaded insert 1/ K = Zinc ni

19、ckel Y = jackpost and 4-40 threaded insert 1/ N = electroless nickel (space applications only) P = Passivated Stainless Steel T = Nickel fluorocarbon polymer 1/ “U” and “Y” designators replaced the “T” and “W” designators which are for 2-56 UNC-2B threaded insert. See table I for supersession data.

20、Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contracto

21、rs are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/15E 6TABLE I.

22、 Hardware supersession data Superseded designator New designator Hardware T U threaded insert 4-40 UNC-2B W Y jackpost and 4-40 UNC-2B threaded insert Referenced documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/1 ASTM A484/A484M A-A-59551 MIL-DTL-83513/3

23、 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-063) NASA-NA DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC, SH Air Force -

24、99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-