DLA MIL-DTL-83513 21 D-2009 CONNECTORS ELECTRICAL RECTANGULAR RECEPTACLE MICROMINIATURE POLARIZED SHELL RIGHT ANGLE SOCKET CONTACTS 4 ROW SOLDER TYPE STANDARD PROFILE 100 CONTACTS .pdf

1、 INCH-POUND MIL-DTL-83513/21D 18 March 2009 SUPERSEDING MIL-DTL-83513/21C 27 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, MICROMINIATURE, POLARIZED SHELL, RIGHT ANGLE, SOCKET CONTACTS, 4 ROW, SOLDER TYPE, STANDARD PROFILE, 100 CONTACTS, PRINTED CIRCUIT BO

2、ARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. AMSC N/A FSC 5935 Inches mm .003 0.08 .007 0.18 .0038 0.097 .010 0.25 .015

3、 0.38 .025 0.64 .050 1.27 .0671 1.704 .125 3.17 .130 3.30 .144 3.66 .150 3.81 .175 4.45 .178 4.51 .185 4.70 .225 5.72 .2712 6.888 .420 10.67 .765 19.43 1.3842 35.159 1.800 45.72 2.500 63.50 2.780 70.61 FIGURE 1. Connector, receptacle, .050 inch (1.27mm) spacing. Provided by IHSNot for ResaleNo repro

4、duction or networking permitted without license from IHS-,-,-MIL-DTL-83513/21D 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). 4. Termination organization area to be optionally molded or filled

5、with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 o

6、r MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M,

7、 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangemen

8、ts A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or

9、GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. 9. Interfacial seals are included with each type receptacle connector. 10. Termination lengths available:

10、 .109 (2.77 mm), .140 (3.56 mm), or .172 (4.37 mm). The tolerance shall be .015 (0.38 mm) for all termination lengths. 11. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-

11、AMS-2700, type 2. FIGURE 1. Connector, receptacle, .050 inch (1.27 mm) spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/21D 3 NOTE: Engaging face of socket insert shown, cavity identification numbers are for referenc

12、e only and do not appear on the part. FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/21D 4 Inches mm .040 1.02 .050 1.27 .100 2.54 .125 3.17 .150 3.81 2.500 63.50 NOTES: 1. Dimensions are in inches. 2. Met

13、ric equivalents are given for information only. FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/21D 5 REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes

14、per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the

15、 requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance

16、with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type2. Wire termination pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Sha

17、ll conform to MIL-DTL-83513/1 and MIL-DTL-83513/3. Plating of termination leads: Solder dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification

18、 sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/21- H 01 A P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware H = 100 01 = .109

19、 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach 03 = .172 C = Cadmium U = 4-40 threaded insert 1/ K = Zinc nickel Y = jackpost and 4-40 threaded insert 1/ N = electroless nickel (space applications only) P = Passivated Stainless Steel T = Nickel f

20、luorocarbon polymer 1/ “U” and “Y” designators replaced the “T” and “W” designators which are for 2-56 UNC-2B threaded insert. See table I for supersession data. Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issu

21、e were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and rela

22、tionship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/21D 6 TABLE I. Hardware supersession data Superseded designator New designator Hardware T U threaded insert 4-40 UNC-2B W Y jackpost and 4-40 UNC-2B th

23、readed insert Referenced documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/1 ASTM A484/A484M A-A-59551 MIL-DTL-83513/3 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing

24、 activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-2007-069) NASA - NA DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-