DLA MIL-DTL-83513 22 D-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL STRAIGHT PIN CONTACTS 2 ROW SOLDER TYPE 9 THROUGH 37 CONTACTS PRINTED CIRCUIT BOAR.pdf

1、 INCH-POUND MIL-DTL-83513/22D 18 March 2009 SUPERSEDING MIL-DTL-83513/22C 27 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, MICROMINIATURE, POLARIZED SHELL, STRAIGHT, PIN CONTACTS, 2 ROW, SOLDER TYPE, 9 THROUGH 37 CONTACTS, PRINTED CIRCUIT BOARD This specificatio

2、n is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm .003 0.08 .0038 0.097 .005 0.13 .015 0.38 .025 0.64 .036 0.91 .050 1.27 .0669 1.699 .

3、096 2.44 .140 3.56 .165 4.19 .1848 4.694 .185 4.70 .190 4.83 .308 7.82 .355 9.02 FIGURE 1. Connector plug, .050 spacing. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/22D 2Number of contacts A Max B .007 (0.18 mm) C

4、.005 (0.13 mm) D E Max 9 1.390 (35.31) 1.150 (29.21) .565 (14.35) .3338 (8.478) .885 (2.48) 15 1.390 (31.31) 1.150 (29.21) .715 (18.16) .4838 (12.289) .945 (24.00) 21 1.690 (40.64) 1.450 (36.83) .865 (21.97) .6338 (16.099) 1.185 (30.10) 25 1.740 (44.20) 1.500 (38.10) .965 (24.51) .7338 (18.639) 1.27

5、5 (32.39) 31 2.040 (51.82) 1.800 (45.72) 1.115 (28.32) .8838 (22.449) 1.575 (40.01) 37 2.340 (59.44) 2.100 (53.34) 1.265 (32.13) 1.0338 (26.259) 1.875 (47.63) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are +.005

6、 inch (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in

7、accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached) when specifie

8、d: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating connector hardwar

9、e does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A - G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927

10、or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. 9. Termination leng

11、ths available: .109 inch (2.77 mm), .140 inch (3.56 mm) or .172 inch (4.37 mm). The tolerance shall be +.015 inch (0.381 mm) for all termination lengths. 10. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel,

12、 passivated in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector plug, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/22D 3NOTE: Engaging face of pin insert shown, cavity identification numbers are for

13、 reference only and do not appear on the part. FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/22D 4NOTE: Engaging face of pin insert shown, cavity identification numbers are for reference only and do not a

14、ppear on the part. FIGURE 2. Insert arrangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/22D 5FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

15、S-,-,-MIL-DTL-83513/22D 6Inches mm .040 1.02 .050 1.27 .096 2.44 .100 2.54 .150 3.81 .225 5.72 .375 9.53 1.150 29.21 1.450 36.83 1.500 38.10 1.800 45.72 2.100 53.34 NOTE: Dimensions are in inches. Metric equivalents are given for information only. FIGURE 3. Layout arrangement - Continued. Provided b

16、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/22D 7REQUIREMENTS: Dimensions and configurations: See figures 1, 2, and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of

17、passing the electrical and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accor

18、dance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in acco

19、rdance with SAE-AMS-2700, type 2. Wire termination pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall conform to MIL-DTL-83513/2 and MIL-DTL-83513/4. Plating of termination leads: Solder

20、 dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a le

21、tter code for the shell finish and hardware column. M83513/22- D 01 A P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware A = 9 01 = .109 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attac

22、h B = 15 02 = .140 C = Cadmium T = threaded insert C = 21 03 = .172 K = Zinc nickel W = jackpost and threaded insert D = 25 N = electroless nickel E = 31 (space applications only) F = 37 P = Passivated Stainless Steel T = Nickel fluorocarbon polymer Changes from previous issue: The margins of this s

23、pecification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of t

24、his document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/22D 8Referenced documents. In addition to MIL-DTL-83513, this d

25、ocument references the following: MIL-DTL-83513/2 ASTM A484/A484M A-A-59551 MIL-DTL-83513/4 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-20

26、07-070) NASA - NA DLA - CC Review activities: Army - AT, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-