DLA MIL-DTL-83513 24 D-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL STRAIGHT PIN CONTACTS 4 ROW SOLDER TYPE 100 CONTACTS PRINTED CIRCUIT BOARD.pdf

1、 INCH-POUND MIL-DTL-83513/24D 18 March 2009 SUPERSEDING MIL-DTL-83513/24C 27 February 2003 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, MICROMINIATURE, POLARIZED SHELL, STRAIGHT, PIN CONTACTS, 4 ROW, SOLDER TYPE, 100 CONTACTS, PRINTED CIRCUIT BOARD This specification is appr

2、oved for use by all Departments and Agencies of the Department of Defense The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. FIGURE 1. Connector, plug, .050 spacing. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction o

3、r networking permitted without license from IHS-,-,-MIL-DTL-83513/24D 2 FIGURE 1. Connector plug, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/24D 3 Inches mm Inches mm Inches mm .003 0.08 .129 3.28 .550 13.

4、97 .0038 0.097 .140 3.56 1.3838 35.149 .005 0.13 .175 4.44 1.800 45.72 .015 0.38 .177 4.50 2.585 65.66 .025 0.64 .185 4.70 2.800 71.12 .050 1.27 .2708 6.878 3.25 82.6 .0669 1.699 .303 7.70 .125 3.18 .460 11.68 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only.

5、3. Unless otherwise specified, tolerances are .005 inch (0.13 mm). 4. Termination organization area to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type

6、SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M pa

7、rts. 6. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating

8、conditions, where as, the mating connector hardware does not exceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM

9、 D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with

10、a minimum of 3 percent lead. 9. Termination lengths available: .109 inch (2.77 mm), .140 inch (3.56 mm) or .172 inch (4.37 mm). The tolerance shall be .015 inch (0.381 mm) for all termination lengths. 10. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M a

11、nd ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector plug, .050 spacing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/24D 4 NOTE: Engaging face of pin ins

12、ert shown, cavity identification numbers are for reference only and do not appear on the part. FIGURE 2. Insert arrangement. Inches mm .040 1.02 .050 1.27 .100 2.54 .125 3.18 .150 3.80 2.800 71.12 FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted with

13、out license from IHS-,-,-MIL-DTL-83513/24D 5 REQUIREMENTS: Dimensions and configurations: See figures 1, 2, and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requirements of MIL-D

14、TL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall conform to the requirements of GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519 or GST-40F in accordance

15、with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Wire termination pins: Wire

16、termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall conform to MIL-DTL-83513/2 and MIL-DTL-83513/4. Plating of termination leads: Solder dipping of termination leads will be accomplished in SN60 PB4

17、0 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): PIN shall consist of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/24-

18、 H 01 A P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (interface critical) Hardware H = 100 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach 03 = .172 C = Cadmium U = 4-40 threaded insert 1

19、/ K = Zinc nickel Y = jackpost and 4-40 threaded insert 1/ N = electroless nickel (space applications only) P = Passivated Stainless Steel T = Nickel fluorocarbon polymer 1/ “U” and “Y” designators replaced the “T” and “W” designators which are for 2-56 UNC-2B threaded insert. See table I for supers

20、ession data. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/24D 6 TABLE I. Hardware supersession data Superseded designator New designator Hardware T U threaded insert 4-40 UNC-2B W Y jackpost and 4-40 UNC-2B threaded insert Changes fr

21、om previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cau

22、tioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/2 ASTM A484/A484M A-A-59551 M

23、IL-DTL-83513/4 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-2007-072) NASA - NA DLA - CC Review activities: Army - AT, MI Navy - AS, CG, MC

24、, SH Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-