DLA MIL-DTL-83513 29 B-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL STRAIGHT PIN CONTACTS 3 ROW SOLDER TYPE STANDARD PROFILE 51 CONTACTS PRINTED CIRCU.pdf

1、INCH-POUNDMIL-DTL-83513/29B 18 March 2009AMSC N/A FSC 5935 SUPERSEDING MIL-DTL-83513/29A 24 May 2004 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, MICROMINIATURE, POLARIZED SHELL, STRAIGHT, PIN CONTACTS, 3 ROW, SOLDER TYPE, STANDARD PROFILE, 51 CONTACTS, PRINTED CIRCUIT BOARD

2、 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm .005 0.13 .0038 0.097.010 0.25 .014 0.36 .015 0.38 .020 0.51 .025 0

3、.64 .036 0.91 .050 1.27 .0669 1.699.088 2.24 .096 2.44 .129 3.28 .140 3.56 .185 4.70 .190 4.83 .2278 5.786.355 9.02 .400 10.16 .9838 24.9891.215 30.86 1.435 36.45 FIGURE 1. Connector plug. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513

4、/29B 2N4. f shall 7 or 4519. 6. ere as, the 7. 519 or -M-24519 or GLCP-30F or GLCP-50 in th 9. .56 mm) or .172 (4.37 mm). The tolerance OTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). Termination o

5、rganization area to be optionally molded or filled with a potting fill material capable opassing the electrical and environmental requirements of MIL-DTL-83513. Plastic moldingconform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519

6、or GST-40F in accordance with ASTM D406MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-25. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. Jackpost (securely attached) when specified: Corrosion resistant steel in accordance with ASTM A48

7、4/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, whmating connector hardware does not exceed the following torque values: 2.5 inch pounds for #

8、2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). Separately molded plastic body (if used) shall be in accordance with type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24GST-40F in accordance with ASTM D4067 or MILaccorda

9、nce with ASTM D5138 or MIL-M-24519. Wire termination pins shall con8. form to A-A-59551, number 24 AWG copper, except shall be tin-lead plated wia minimum of 3 percent lead. Termination lengths available: .109 (2.77 mm), .140 (3shall be +.015 (0.381 mm) for all termination lengths. Threaded insert,

10、when specified: Corrosion resistant steel in accordance with ASTM A484/A484M10. and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. FIGURE 1. Connector plug- Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

11、se from IHS-,-,-MIL-DTL-83513/29B 3NOTE: Engaging face of pin insert shown, cavity identification numbers are for reference only and do not appear on the part. FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-8351

12、3/29B 4Inches mm .0375 0.95 .040 1.02 .075 1.91 .096 2.44 .2325 5.91 .750 18.54 1.215 30.86 FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/29B 5REQUIREMENTS: Dimensions and configurations: See figures 1, 2

13、 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic bo

14、dy or plastic molding: Shall conform to the requirements of GDI-30F or SDG-30F of ASTM D5948, or GPT-30F or GET-30F or GCT-30F of ASTM D5927 or MIL-M-24519 or GST-40F of ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50F in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant stee

15、l in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Wire termination pins: Wire termination pins shall be in accordance with A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 perc

16、ent lead. Mating connector: Shall be in accordance with MIL-DTL-83513/2 and MIL-DTL-83513/4. Plating of termination leads: Solder dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Part or Identifying Number (PIN): The PIN shall consist of the l

17、etter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/29- G 01 C P Specification sheet number Insert arrangements (see figure 2) Termination length Shell finish (

18、interface critical) Hardware G = 09 01 = .109 02 = .140 A = Pure electrodeposited aluminum N = No hardware or threaded insert P = jackpost attach 03 = .172 C = Cadmium T = threaded insert K = Zinc nickel W = jackpost and threaded insert N = electroless nickel (space applications only) P = Passivated

19、 Stainless Steel T = Nickel fluorocarbon polymer Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Provided by IHSNot for ResaleNo reproduction or networki

20、ng permitted without license from IHS-,-,-MIL-DTL-83513/29B 6Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and

21、relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-83513, this document references the following: MIL-DTL-83513/2 ASTM A484/A484M A-A-59551 MIL-DTL-83513/4 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 CONCLUDING MAT

22、ERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-2007-077) NASA - NA DLA - CC Review activities: Army - AT, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-