DLA MIL-DTL-83528 3 E-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC ELASTOMER EMI RFI SOLID 揇 SHAPED STRIP.pdf

1、 MIL-DTL-83528/3E 13 August 2013 SUPERSEDING MIL-DTL-83528/3D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, SOLID “D” SHAPED STRIP This specification is approved for use by all Departments and Agencies of the Department

2、of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. NOTES: 1. Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 2. Tolerance on flash shall be

3、.008 (0.20 mm) on the extension and .005 (0.13 mm) on the thickness. 3. Length shall be as specified on the purchase order. FIGURE 1. EMI/RFI “D” shaped strip gasket. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DT

4、L-83528/3E 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN 1/ M83528/003X Dimension A .005 2/ Dimension B .005 2/ 3/ Dime

5、nsion C .005 2/ 3/ Cross section 4/ area (cm2) 001 .031 (0.78) .062 (1.57) .068 (1.73) .025 002 .047 (1.19) .094 (2.39) .078 (1.98) .041003 .039 (0.99) .078 (1.98) .089 (2.26) .041 004 .047 (1.19) .094 (2.39) .094 (2.39) .050005 .031 (0.78) .062 (1.57) .100 (2.54) .037 006 .075 (1.91) .150 (3.81) .1

6、10 (2.79) .091007 .061 (1.55) .122 (3.10) .135 (3.43) .097 008 .059 (1.49) .118 (3.00) .156 (3.96) .109009 .078 (1.98) .156 (3.96) .156 (3.96) .140 010 .089 (2.26) .178 (4.52) .175 (4.45) .179011 .094 (2.39) .188 (4.78) .188 (4.78) .203 012 .125 (3.18) .250 (6.35) .250 (6.35) .3601/ “X” in the PIN s

7、hall be replaced by the applicable material type. Complete PIN example: M38528/003A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ For dimensions over .200 the tolerances shall be .008. 4/ For calculation of volume resistivity (f

8、or reference only). TABLE II. Supersession information. PIN 1/ M83528/003X Superseded DESC Drawing PIN 85104X 1/ 001 002 002 003 003 004 004 010 005 005 006 006 007 /2 007008 008 009 N/A 010 009 011 012 012 013 1/ “X” in the PIN indicates the applicable material type. 2/ Dimensions of this part are

9、not identical to the superseded part. However, this is an authorized substitution. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes

10、 no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reprod

11、uction or networking permitted without license from IHS-,-,-MIL-DTL-83528/3E 3 Referenced document. This document references MIL-DTL-83528. Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-012) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activiti

12、es listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-