DLA MIL-DTL-83528 4 F-2013 GASKETING MATERIAL CONDUCTIVE SHIELDING GASKET ELECTRONIC EMI RFI CONNECTOR FLANGE MOUNT.pdf

1、 MIL-DTL-83528/4F 11 January 2013 SUPERSEDING MIL-DTL-83528/4E 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, EMI/RFI, CONNECTOR FLANGE MOUNT This specification is approved for use by all Departments and Agencies of the Department of Defense

2、. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-DTL-83528. NOTES: Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. FIGURE 1. EMI/RFI connector gasket. AMSC N/A FSC 5

3、999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/4F 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, G, H, J, K, L, or M. Connector shell size: See tables I and II. Part or I

4、dentifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN M83528/004X 1/ Dimension 2/ ConnectorShell Size Cross section(cm2) 3/ A .010 B + .020 - .000 C .015 D .010 001 .469 (11.91 mm) .375 (9.53 mm) .738 (18.75 mm) .141 (3.58 mm) 6 .037 002 .594 (15.09 m

5、m) .630 (16.00 mm) .840 (21.34 mm) .135 (3.43 mm) 8 .022 003 .594 (15.09 mm) .568 (14.43 mm) .812 (20.62 mm) .125 (3.18 mm) 8 .025 004 .594 (15.09 mm) .500 (12.70 mm) .875 (22.23 mm) .156 (3.96 mm) 8 .039 005 .719 (18.26 mm) .750 (19.05 mm) .965 (24.61 mm) .135 (3.43 mm) 9,10 .022 006 .719 (18.26 mm

6、) .680 (17.27 mm) .937 (23.80 mm) .125 (3.18 mm) 10 .027 007 .719 (18.26 mm) .625 (15.88 mm) 1.000 (25.40 mm) .156 (3.96 mm) 10S,SL .039 008 .812 (20.62 mm) .875 (22.23 mm) 1.060 (26.92 mm) .141 (3.58 mm) 11,12 .019 009 .813 (20.65 mm) .750 (22.10 mm) 1.094 (27.79 mm) .141 (3.58 mm) 12,12S,SL .036 0

7、10 .906 (23.01 mm) 1.005 (25.53 mm) 1.153 (29.29 mm) .135 (3.43 mm) 13,14 .015 011 .906 (23.01 mm) .938 (23.83 mm) 1.125 (28.58 mm) .125 (3.18 mm) 14 .019 012 .906 (23.01 mm) .875 (22.23 mm) 1.188 (30.18 mm) .156 (3.96 mm) 14,14S .032 013 .969 (24.61 mm) 1.135 (28.83 mm) 1.258 (31.95 mm) .156 (3.96

8、mm) 15,16 .013 014 .969 (24.61 mm) 1.063 (27.00 mm) 1.250 (31.75 mm) .125 (3.18 mm) 16 .019 015 .969 (24.61 mm) 1.000 (25.40 mm) 1.281 (32.54 mm) .156 (3.96 mm) 16,16S .029 016 1.062 (26.97 mm) 1.260 (32.00 mm) 1.351 (34.32 mm) .156 (3.96 mm) 17,18 .009 017 1.062 (26.97 mm) 1.189 (30.20 mm) 1.343 (3

9、4.11 mm) .125 (3.18 mm) 18 .016 018 1.062 (26.97 mm) 1.135 (28.83 mm) 1.375 (34.93 mm) .156 (3.96 mm) 18,18S .025 019 1.156 (29.36 mm) 1.375 (34.93 mm) 1.500 (38.10 mm) .141 (3.58 mm) 19,20 .013 020 1.156 (29.36 mm) 1.312 (33.32 mm) 1.467 (37.26 mm) .125 (3.18 mm) 20 .016 021 1.156 (29.36 mm) 1.250

10、(31.75 mm) 1.500 (38.10 mm) .172 (4.37 mm) 20 .016 022 1.250 (31.75 mm) 1.500 (38.10 mm) 1.625(41.28 mm) .141 (3.58 mm) 21,22 .026 023 1.250 (31.75 mm) 1.437 (36.50 mm) 1.562 (39.67 mm) .125 (3.18 mm) 22 .013 024 1.250 (31.75 mm) 1.375 (34.93 mm) 1.625 (41.28 mm) .172 (4.37 mm) 22 .013 025 1.375 (34

11、.93 mm) 1.625 (41.28 mm) 1.750 (44.45 mm) .172 (4.37 mm) 23,24 .026 026 1.375 (34.93 mm) 1.563 (39.70 mm) 1.703 (43.26 mm) .152 (3.86 mm) 24 .013 027 1.375 (34.93 mm) 1.500 (38.10 mm) 1.750 (44.45 mm) .203 (5.16 mm) 24 .015 028 1.500 (38.10 mm) 1.750 (44.45 mm) 1.875 (47.63 mm) .172 (4.37 mm) 25 .01

12、6 029 1.562 (39.67 mm) 1.750 (44.45 mm) 2.000 (50.80 mm) .203 (5.16 mm) 28 .013 030 1.750 (44.45 mm) 2.000 (50.80 mm) 2.250 (57.15 mm) .219 (5.56 mm) 32 .026 031 1.938 (49.23 mm) 2.250 (57.15 mm) 2.500 (63.50 mm) .219 (5.56 mm) 36 .026 032 2.188 (55.58 mm) 2.500 (63.50 mm) 2.750 (69.85 mm) .219 (5.5

13、6 mm) 40 .026 033 2.375 (60.33 mm) 2.781 (70.63 mm) 3.000 (76.20 mm) .219 (5.56 mm) 44 .023 034 2.625 (66.68 mm) 3.031 (76.99 mm) 3.250 (82.55 mm) .219 (5.56 mm) 48 .023 035 .500 (12.70 mm) .437 (11.10 mm) .800 (20.32 mm) .135 (3.43 mm) 4/ .037 036 .500 (12.70 mm) .437 (11.10 mm) .687 (17.45 mm) .13

14、5 (3.43 mm) 4/ .026 1/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M83528/004A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ For calculation of volume resistivity (for reference only).

15、 4/ Connector shell size data available for -035 and -036. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/4F 3 TABLE II. Connector shell size. PIN M83528/ 004X MIL-DTL-38999 MIL-C-81511SAE AS90484 SAE AS50151 MIL-DTL- 83723 NAS 1599(in

16、active 6/1980) MIL-DTL- 26482 Series I Series II Series IV 001 6 6 6 002 8 003 8 8 004 8 8 8 8 005 9 10 006 10 10 007 10 10 10 10 008 11 12 11 009 12 12 12 12 010 13 14 13 011 14 14 012 14 14 14 14 013 15 16 15 014 16 16 015 16 16 16 16 016 17 18 17 017 18 18 018 18 18 18 18 019 19 20 19 020 20 20 0

17、21 20 20 20 20 022 21 22 21 023 22 22 024 22 22 22 22 025 23 24 23 026 24 24 027 24 24 24 24 028 25 25 029 28 030 32 031 36 032 40 033 44 034 48 035 1/ 036 1/ 1/ Connector shell size data is unavailable for -035 and -036. Provided by IHSNot for ResaleNo reproduction or networking permitted without l

18、icense from IHS-,-,-MIL-DTL-83528/4F 4 TABLE III. Supersession information. PIN 1/ M83528/004X Superseded DESC Drawing PIN 85099X 1/ PIN 1/ M83528/004X Superseded DESC Drawing PIN 85099X 1/ 001 001 019 019002 002 020 020003 003 021 021004 004 022 022 005 005 023 023006 006 024 024007 007 025 025008

19、008 026 026 009 009 027 027010 010 028 028011 011 029 029012 012 030 030 013 013 031 031014 014 032 032015 015 033 033016 016 034 034 017 017 035 N/A 018 018 0361/ “X” in the PIN indicates the material type. Changes from previous issue. The margins of this specification are marked with vertical line

20、s to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire conte

21、nt irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-83528, this document references the following: MIL-DTL-38999 MIL-C-81511 SAE AS90484 SAE AS50151 MIL-DTL-83723 NAS 1599 MIL-DTL-26482 Custodians: Preparing activity: Ar

22、my CR DLA CC Navy EC Air Force 85 (Project 5999-2013-003) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-