1、 MIL-DTL-83528/6E 3 September 2013 SUPERSEDING MIL-DTL-83528/6D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, RECTANGULAR, D-CROSS SECTION This specification is approved for use by all Departments and Agencies of the Dep
2、artment of Defense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. NOTE: 1. Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 2. Tolerance on flash sh
3、all be .008 (0.20 mm) on the extension and .005 (0.13 mm) on the thickness. FIGURE 1. EMI/RFI gasket, elastomer, rectangular with “D” cross section. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/6E 2 REQUI
4、REMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN 1/ M83528/006X W 2/ L 2/ Cross Section Area (cm2) 3/ Min Max Min Max 001 .285 (7
5、.24) .295 (7.49) .983 (24.97) .993 (25.22) .057 002 .485 (12.32) .495 (12.57) .983 (24.97) .993 (25.22) .057 003 .619 (15.72) .629 (15.98) 1.243 (31.57) 1.253 (31.83) .057 004 .815 (20.70) .845 (21.46) 2.985 (75.82) 3.015 (76.58) .057 005 1.325 (33.66) 1.355 (34.42) 5.265 (133.73) 5.295 (134.49) .05
6、7 1/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M38528/006A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ For calculation of volume resistivity (for reference only). TABLE II. Superse
7、ssion information. PIN 1/ M83528/006X Superseded DESC Drawing PIN 85100X 1/ 001 001002 002 003 0031/ “X” in the PIN indicates the applicable material type. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue
8、were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relati
9、onship to the last previous issue. Referenced documents. This document references MIL-DTL-83528. Custodian: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-014) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this docu
10、ment as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1